similar to: X100P clone card problem

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Looking for some help from the UK please. I backed up all my Asterisk configuration before re-installing the server from 32 -> 64 bit. Unfortunately I did not transfer the backup to another machine!!!!! I now have a TDM400P that is not picking up the line. Can you see what I have done wrong when I have rebuilt the config please: dahdi_scan ---------- [1] active=yes alarms=OK

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

Hello all- I have a Digium TE410P in an HP DL145 G2 dual processor server that generates well over 100,000 interrupts per second (sometimes I?ve counted 160,000+ per second) generally resulting in either the system becoming swamped and unusable or the kernel disabling the IRQ the TE410P is on resulting in the spans on that card being unusable. I have confirmed that the card is good by placing it

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

dahdi_cfg -vvv error `cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or directory` PRI show spans --command not found test call not working. -- dahdi_genconf -vvv Default parameters from /etc/dahdi/genconf_parameters Generating /etc/dahdi/assigned-spans.conf cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or

Hi Asterisk Users, We've been experiencing some tough time regarding a new Asterisk installation connected to the PSTN via an ISDN PRI with a Digium TE121 with the optional VPMADT032 echo cancellation module. For now, I'll focus on something very specific which is summarized on this email's subject. However, here are some general facts for the context: - System pbxfri went

Hello, I just bought a TE121 T1/E1 card, and now trying to install it on a 1.4.23.1 asterisk with dahdi 2.1.0.4 Actually first everything went on well and i managed to see my card on dahdi. Here's the output: #asterisk# dahdi_hardware pci:0000:04:08.0 wcte12xp+ d161:8000 Wildcard TE121 and this is the scan: -------------------------- asterisk# dahdi_scan [1] active=yes alarms=RED

Usually I used real Digium cards in asterisk systems, so I'm running into this for the first time. dahdi_tool reports that dahdi_dummy is in state UNCONFIGURED. This isn't super surprising, as it seems like the configuration files for DAHDI are really intended only for configuring real physical cards. But that begs the question: Is there any legal DAHDI configuration for dahdi_dummy such

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done

I am getting the following warnings on the CLI when loading Asterisk 1.6.1-rc1: [Feb 12 12:32:34] NOTICE[22261]: timing.c:59 ast_install_timing_functions: Multiple timing modules are loaded. You should only load one. [Feb 12 12:32:34] ERROR[22261]: codec_dahdi.c:398 find_transcoders: Failed to open /dev/dahdi/transcode: No such file or directory [Feb 12 12:32:33] WARNING[22261]:

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Hi Eric, > On 12 avr. 2016, at 17:48, Eric Cooper <ecc at cmu.edu> wrote: > > On Tue, Apr 12, 2016 at 04:36:58PM +0200, Bertrand LUPART - Linkeo.com wrote: >> I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : >> [...] >> However, i can't find any dahdi startup script, neither init.d neither systemd