similar to: Dahdi_genconf does not generate NT/TE configuration

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment***************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ****************************************************************** In my case , I set prot 1 and

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

Hello, 1. How can specify in /etc/dahdi/genconf_parameters file that a port from a B410P board is to be "disabled". Playing with comments (see bellow) doesn't help : file /etc/asterisk/dahdi-channels.conf is filled with 4 ports data. pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 TE # SPAN/4 TE 2. How can specify groups in

Hi, My genconf_parameter is : # grep -v "^#" genconf_parameters lc_country fr context_lines remote group_lines 1 bri_sig_style bri echo_can oslec pri_termtype SPAN/* NT (I also tried various identations and syntax for pri_termtype line such as bri_termtype but I still get the same output file). But still, generated system.conf contains

Hi all, As i tested with Asterisk+dahdi+libpri with openvox BRI with NT mode, the ISDN phone does not work. There is the setting and error. ***********************Enviroment********************************** Asterisk-1.6.1.18 dahdi-linux-2.3.0.1 dahdi-tool-2.30. libpri-1.4.11.2 CentOS-5.5 OpenVox B400P ******************************************************************** In my case , I set prot 1

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hello, On a very new system, I've got : # cat /etc/dahdi/genconf_parameters | grep -v "^#" lc_country fr context_lines remote group_lines 1 bri_sig_style bri_ptmp echo_can oslec pri_termtype SPAN/1 TE SPAN/2 TE SPAN/3 TE SPAN/4 TE # dahdi_genconf Empty

Hi, I have 3 ISDN lines using the digium B410P card. Incoming and outgoing call are working. I use the following version : * libpri-1.4.10.2 * dahdi-2.2.1.1 * asterisk-1.6.2.6 On incoming calls, DTMF is not working, i can't see any logs. Here are the main configuration files : dahdi-channels.conf ;; Span 2: B4/0/1 "B4XXP (PCI) Card 0 Span 1" signalling=bri_cpe

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Hi everybody, I have a 1.6.0.5 asterisk system and I?m having many problems with my pstn cards. This system has a Digium B410P with 4 BRIs configured, and an OpenVox A400E. The issue is that it?s impossible to make the system recognize the A400E, despite the ?lspci? output is: 0a:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 11:00.0 ISDN controller: Digium,

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi, I'm using Asterisk 1.6.1.18 with latest Dahdi Linux and Tools (rev 8854) and libpri 1.4.10.2. During installation, I'm facing this : # dahdi_genconf -v system Default parameters from /etc/dahdi/genconf_parameters Empty configuration -- no spans Of course, I've got span descriptions in /etc/dahdi/genconf_parameters : .... pri_termtype SPAN/1 TE SPAN/2

Hi, 1. Has someone met any success at all, connecting a Digium B410P to a Patton Smartnode 4638 (with latest 5.3 firmware) ? 2. If positive, then, which signalling was used on both sides ? My project's goal is use a Patton Smartnode 4638 to act as telco BRI lines, from a B410P-enabled asterisk box. In my testings, I can see channel is respectively up (with patton web server status page)

Hi All, I am facing problem with E1 line. I have installed Asterisk (1.4.20.1) on a system with Digium TE420 card (Zaptel- 1.4.10) But every now and then I face problem of down E1's. The log show lot of entries like "pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2" This happens on a regular basis and the E1 becomes up after some time. My

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

Hi, 1. Is there any manual entry about modprobe's options relative to a given Dahdi driver (wctdm24xxp, for instance) ? 2. When loading a wctdm24xxp driver, is there any parameter to pass to modprobe to configure a span in NT/point to point mode ? 3. After running dahdi_cfg -vvvvv , I can read with dmesg : [ 1986.289277] wctdm24xxp 0000:04:06.0: xhfc: Configuring port 0 span 1 in TE mode

2011/6/14 Kevin P. Fleming <kpfleming at digium.com> > On 06/14/2011 03:11 PM, Olivier wrote: > >> Hi, >> >> 1. Is there any manual entry about modprobe's options relative to a >> given Dahdi driver (wctdm24xxp, for instance) ? >> >> 2. When loading a wctdm24xxp driver, is there any parameter to pass to >> modprobe to configure a span in

Hello, I just installed a Debian Jessie box from scratch which sports a Digium TE435 digital card. I installed the software, built and loaded the kernel modules: # dpkg -l|grep dahdi ii asterisk-dahdi 1:11.13.1~dfsg-2+b1 amd64 DAHDI devices support for the Asterisk PBX ii dahdi 1:2.10.0.1-1 amd64

I have a pretty large setup on one of my customers. Digium TE420B (with echo cancelling module), 3 Xorcom Astribanks with 32 FXS each and 1 Xorcom Astribank with 16 FXO. These FXO ports are NOT used for fax/data transmission, as they are connected to cell phones. Not really related to the issue, but there are also 250 SIP phones. The problem is that fax and dial-up connections are really