similar to: DAHDIScan() only returns dead air

Displaying 20 results from an estimated 600 matches similar to: "DAHDIScan() only returns dead air"

2007 Jan 16
0
zaptel hardware detection with genzaptelconf
Hi Someone complained in #asterisk-gui that the Zaptel hardware detection did not work. It seems that zapscan.bin did not work properly, as no /etc/asterisk/zapscan.conf was generated. Solution: detect zaptel hardware with genzaptelconf, and generate zapscan.conf from it. genzaptelconf grep '^fx[os][kl]s=' /etc/zaptel.conf \ | sed 's/\(fx[os]\)..=\(.*\)/[\2]\nport=\1\n/'
2010 Oct 20
1
echo on TE122
I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware
2009 Mar 27
4
Help: RED alarm on Wildcard TE122 card
Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked
2008 Feb 04
1
asterisk-gui installation hangs
Hi, I use asterisk branch 1.4 and gui 1.4 as well. I have the following situation: When I try to make gui configuration by http://localhost:8088/asterisk/static/config/setup/install.html I can see that application logs my user correctly but there is no browser window shift to the next page. it stays at the logging one. I get the following info in the console: [Feb 4 09:33:09] == Parsing
2010 Nov 29
1
Trouble with TE122 on HP DL120G6 - can't disable USB
I have recently built a single-T1 Asterisk box using an HP DL120G6 with a Digium TE122 card. I was finding that I was getting missed interrupts on the TE122, causing the driver to report that it was increasing latency. It kept doing this until the T1 did not work reliably. I tried my usual procedure of disabling the USB subsystem in the BIOS (or so I thought), but I found that the USB drivers
2010 Nov 27
1
DAHDI 2.4.0 produces HDLC errors with echo canceler
Hi, After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC errors on my console: [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 These errors prevented calls from being made and received on my PRI spans. This seems
2009 Apr 29
1
US Caller ID
Okay, I can't find what might be causing this. Here is what I got: Asterisk server hooked up to a digital T1 line (full 24-channel) via a Digium card. Verizon has turned on caller ID on the first line (I can guarantee it is on as I can hear the FSK tones on this line but not the others). Using zttool an ZapScan() I have determined the following: 1) The RxB/RxD bits toggle from 1 to 0
2009 Nov 16
1
Problems with dahdi on asterisk 1.6.1.9 with TE122
Hello, I am installing dahdi on a machine lspci 00:00.0 Host bridge: Intel Corporation 3200/3210 Chipset DRAM Controller (rev 01) 00:01.0 PCI bridge: Intel Corporation 3200/3210 Chipset Host-Primary PCI Express Bridge (rev 01) 00:06.0 PCI bridge: Intel Corporation 3210 Chipset Host-Secondary PCI Express Bridge (rev 01) 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
2009 Mar 27
2
TE122
Does anyone know if the TE122 is recognized by any of the 1.2 zaptel drivers? It seems that 1.2.16 knows it not... :) Cheers, j
2003 Sep 11
1
Final version of ZapScan
Hey folks -- Some of you had asked about getting my modification to ZapBarge that lets you monitor active Zap channels, scanning through them with the # key. I had posted a version a few days ago that was pretty crude; it didn't check to see which channels were active and assumed you had 23. I've finished a new version that checks to see what channels are actually active and pulls
2007 Jan 10
0
app_system.c:105 system_exec_helper: Unable to execute '/sbin/zapscan.bin'
When I load the asterisk 1.4 gui and log into "/asterisk/static/config/setup/install.html", it tells me "No Analog ports has been detected on your system". I have 2 Wildcard X100P cards that are properly installed. Ztcfg shows no problems. I also get the following message from the asterisk console " app_system.c:105 system_exec_helper: Unable to execute
2008 Jan 16
2
Difference between TE121 and TE122
What's the difference between the TE121 and TE122. I read the description on Digium's site and it isn't clear to me. Best regards, -- Guilherme Loch G?es Visite nossa loja virtual: http://www.shopvoip.com.br Not?cias e F?rum sobre VoIP com software livre: http://www.asteriskexperts.com.br -------------- next part -------------- An HTML attachment was scrubbed... URL:
2016 Nov 11
3
dahdi_scan
lspci | grep Digium 03:05.0 Ethernet controller: Digium, Inc. Wildcard TE122 single-span T1/E1/J1 card (rev 11) dahdi_scan So I have a card in a box - lspci shows it... dahdi_scan reports nothing. Is my card dead? Jerry -------------- next part -------------- An HTML attachment was scrubbed... URL:
2006 Jan 08
3
Monitor Logged in Agent's conversation
Hi, Is it possible to monitor conversation of logged in Agents? Currently I am using ZapScan to monitor incoming calls, but I would like to monitor individual agents. raj
2009 Sep 29
3
chanspy and DISA
Hello all, OS OpenSuSE 10.3 * ver 1.4.26.2 zaptel ver. 1.12 Digium TE122 I have a request for remote users to be able to dial through the system so that the sales managers can barge/chanspy on the sales force. I have the DISA part working with authentication(rather straight forward) but what I can not figure out is how to enable the supervisors to be able to barge on these calls. Is there a
2005 Mar 19
3
ZapBarge restrictions?
Anyone successfully implemented a solution for allowing ZapBarge call monitoring only for a specific group of agents calls? The issue I see is that the feature only works on zap channels, and all of the agents (in many cases) are IP phones. Allowing ZapBarge and ZapScan on the TDM PSTN (t100p) interface has privacy issues for senior managers, but would allow all outbound zap calls to be
2007 Apr 26
1
AsteriskNOW generation of zapata.conf file
From: Malcom Kemp Sent: Wednesday, April 25, 2007 11:19 AM To: 'asterisk-users@lists.digium.com' Subject: AsteriskNOW generation of zapata.conf file I am a new user of Asterisk, and an trying to use AsteriskNOW. The test system is dual processor, so I am using the beta 4 version. I am currently trying to manually configure, as the GUI does not seem to let me accomplish what I need.
2008 Feb 15
2
HPEC
Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm
2010 May 24
4
convert zaptel to dahdi?
I am trying to get a zaptel install converted to dahdi. I can get dahdi installed, and the pseudo device even shows up; however, dahdi show channels shows me nothing. There is a TE122 and a TDM800 in there, and neither show up. dahdi show status shows both cards, and dahdi tools show that the cards are there, working, and have no alarms. What am I missing? Michael Munger, dCAP, MCPS, MCNPS,
2004 Sep 05
3
ChanSpy by anthm and more...
Everyone we have a few new things to give back to the asterisk community. http://bugs.digium.com/bug_view_page.php?bug_id=0002379 http://bugs.digium.com/bug_view_page.php?bug_id=0002380 http://bugs.digium.com/bug_view_page.php?bug_id=0002381 These include app_chanspy, the ability to spy on ANY bridged call taking place inside asterisk. NOT just ZAP as with ZapScan/Barge. Native format_* files