similar to: Asterisk on DD-WRT : modules.conf not found

Hi Everyone, I have tried to set the box to DMZ and also tried to port forward 5060 TCP/UDP and 10000/20000 UDP to the server IP but it's no use and there is a no audio issue. I am pretty certain it's a NAT issue as the sip call establishes. I also made a succesful IAX2 call through IAX trunking and zap lines on this server but sip doesn't work. I register to an extension but even

I''m trying to setup a DD-WRT router (www.dd-wrt.com; embedded micro-device linux for the uninitiated) to rate limit all the traffic it receives from its wi-fi interface. I followed the instructions from the cookbook section on rate limiting (http://lartc.org/howto/lartc.ratelimit.single.html), but it doesn''t appear to be working. I tested by checking my laptop''s

Hi all, I'm trying to use a wrt54gl router running dd-wrt as a provisioning server for a remote installation. I've got dhcp working and I have provisioning files ready to go. I understand that I need to set bootp option 66 to point to the tftp/ftp/http server. In fact, I have this working completely with the ISC dhcp server The problem is that I don't know how to get

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Steve, 1) go to /etc/asterisk 2) open modules.conf for editing using vi 3) add this line: noload=pbx_wilcalu.so 4) Save the file 5) Restart asterisk Lightup the candles, open the Cabernet Savignon ( or whatever your prefernce) and call your girlfriend. ;) Seshu -----Original Message----- From: asterisk-users-bounces@lists.digium.com

We have a machine with a TE410P in it acting as a client to route calls via iax2 to our central server, caller --> ( zap -> iax ) ---> ( iax -> whatever ) --> called client server often the called can't hear the caller (both machines on public ip) 'iax2 show netstats" on client machine shows more and more dropped packets on the

Hi :) I've had all this working before, but I'm revisiting it, and in short, I currently have huge problems receiving incoming calls. I've been trying with both FWD and voiptalk.org. I'm running CVS HEAD of asterisk, zaptel and libpri as of yesterday afternoon. Would someone mind helping? :) My machine is 10.0.0.1 on my LAN, but the ADSL router has 10.0.0.1 set as the 'DMZ

so here it is, the problem that's been nagging me for the past 2 days: connected a box to my telco's NTBA <-> zap/asterisk. which works: box:/etc/asterisk# cat /proc/zaptel/1 Span 1: ZTHFC1 "HFC-S PCI A ISDN card 0 [TE] layer 1 ACTIVATED (F7)" HDB3/CCS 1 ZTHFC1/0/1 Clear (In use) 2 ZTHFC1/0/2 Clear (In use) 3 ZTHFC1/0/3 HDLCFCS (In

Hi * Fans, I have some fritz cards now, followed instructions from stuart hirsts email of Jun 28: -> Thanks for your info but I think I have it working at last. Below are the steps I took which might help others. 1) Download the PCI AVM drivers from ftp://ftp.avm.de/cardware 2) Download the Chan_capi from http://www.junghanns.net/asterisk/ 3) tar -xvzf fcpci-suse8.0-03.09.10.tar.gz which

This is my musiconhold.conf and my folder: root@voip:/etc/asterisk# less musiconhold.conf [classes] default => quietmp3:/var/lib/asterisk/mohmp3 ;loud => mp3:/var/lib/asterisk/mohmp3 ;random => mp3:/var/lib/asterisk/mohmp3,-z ;unbuffered => mp3nb:/var/lib/asterisk/mohmp3 ;quietunbuf => quietmp3nb:/var/lib/asterisk/mohmp3 ; Note that the custom mode cannot handle escaped parameters

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Hi all, What hell hapen here? asterisk:/etc/asterisk# /etc/init.d/dahdi startLoading DAHDI hardware modules:FATAL: Error inserting dahdi (/lib/modules/2.6.26-2-686/dahdi/dahdi.ko): Device or resource busy wct4xxp: done wcte12xp: done wct1xxp: done wcte11xp: done wctdm24xxp: done wcfxo: done wctdm: done wcb4xxp: error wctc4xxp: done xpp_usb: doneError: missing /dev/dahdi! When

Hello there ! I have successfully installed Asterisk on a normal server and on a Linksys WRT610N with DD-WRT running from connected USB-stick. This is not my first Asterisk-installation. I'm always finding a smaller and smaller platform to install Asterisk on. But now I encounter a problem. I'm using the same Grandstream GXP2010 with a of my installations. Every time registration goes

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi I have installed 2 fx0 cards into a machine 1 for pstn (out) and the other for pstn (in) However I can get the first card (pstnout to work fine) I have swapped the cards and both work I am also unable to make outgoign on the second card ztcfg -v shows r2d2:/etc/asterisk# ztcfg -v Zaptel Configuration ====================== 2 channels configured. My /etc/zapdata.conf file # fxsks=1,2

Hi, I'm trying to install Asterisk onto a fresh install of Slackware 9.1... I've installed all packages in A, AP, D, E, F, K, L, N... So basically what's needed for a text based system with development, networking, docs, libraries.. No X-Windows, no games, no TCL/TEX etc. Following the commands on the Asterisk website I checked out the CVS source and started compiling... Zaptel and

Does anybody have realtime queue members working? Not the queues themselves, just the members. I have realtime working for voicemail and sippeers, but I can't get queue members to work. Here is what I have: res_mysql.conf: [general] dbhost = 127.0.0.1 dbname = ASTERISK dbuser = myuser dbpass = mypass dbport = 3306 dbsock = /tmp/mysql.sock queues.conf: [general]

Hi All Just a quick check on the best way to ensure multiple cards/devices load in the correct order. Asterisk 1.8 with Sangoma A101 had no problems until we introduced an Astribank. root at pabx377:/etc/asterisk# dahdi_hardware -v usb:001/004 xpp_usb+ e4e4:1162 Astribank-modular FPGA-firmware LABEL=[usb:X1060395] CONNECTOR=@usb-0000:00:1d.7-3 XBUS-00/XPD-00:

Hi Has anyone had any luck in putting two of these im a box? May I ask how.... I am starting to go bald.... I do have a suggestion is make another box and link them with iax2 Thanks Samantha r2d2:/home/s/samantha# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) 2