similar to: ooh323 doesn't know what to do when bridging calls

Hi all. Trying to setup H.323 via Asterisk between a PLANET H.323 box and my SIP phones. When calling from the SIP phones, it connects but quickly disconnects citing the following error message: **** --- build_peer +++ build_peer +++ reload_config +++ ooh323_do_reload -- Executing Dial("SIP/yyy-2965", "OOH323/203@xxx") in new stack --- ooh323_request - data

has anyone managed to get these three beasties to work together ? we're using ooh323 from asterisk-addons-1.2.2, asterisk 1.2.6 and microsoft netmeeting default from windows xp. the symptoms are that calls from a SIP client to NetMeeting rings on NetMeeting, but upon answering the call in NetMeeting, no audio is passed between the two. eventually, the call times out and hangs up. on a

I terminate some calls on a h323 device (a quescom gsmgateway) from asterisk 1.2.3 with ooh323, the customer is complayining about choppy sound on most of the calls, the only warning message I can see is : src/chan_h323.c:944 ooh323_indicate: Don't know how to indicate condition -1 on ooh323c_102 (the calls sounds perfectly with iax/zap termination and the quescom seems to work fine with

Hi, I am using asterisk 1.4. I have confgured the musiconhold.conf file. However, when i make a call and then hold the call it does nothing. in the CLI i do not see the starting/stopping musiconhold messages. i am making calls from sip to h323 using asterisk assip/h323 gateway (with gnugk and ooh323). i get the following messages when putting the call on hold: -- Executing [204 at default:1]

Hi, I'm trying to configure Asterisk as SIP-H.323 Gateway via ooh323, but I have an error relatively to the GK Confirmation message. >From the log: "H323 RAS channel creation - succesful Sent GRQ message Gatekeeper Confirmed (GCF) message received ERROR:No Gatekeeper ID present in received GKconfirmed message Ignoring message and will retransmit GRQ after timeout Error: Failed to

OOH323 Debugging Enabled -- Executing Answer("SIP/3513-090f7d40", "") in new stack -- Executing Wait("SIP/3513-090f7d40", "1") in new stack -- Executing DeadAGI("SIP/3513-090f7d40", "a2billing.php|1") in new stack -- Launched AGI Script /var/lib/asterisk/agi-bin/a2billing.php a2billing.php|1: line:58 - IDCONFIG : 1

All, I'm running (attempting to) ooh323 with Asterisk and a Cisco 2621XM router operating as a H.323 GateKeeper, however when I bring the Asterisk box up it registers successfully with the GateKeeper (exchanges GRQ/GCF, then RRQ/RCF) it notes the GateKeeper supports keepalive at 300 seconds, when it gets to time to re-register its sends an RRQ again and gets rejected with RRJ (unspecified

Hello, I'm trying to create a H.323 trunk between Asterisk 11 and Avaya. I have done this before between Asterisk 1.6 and Avaya but had some issues placing external calls from the Asterisk to the Public network which is connected to Avaya. I'm trying to create that trunk on Asterisk 11 because the 1.6 is outdated and has no support. On the Asterisk side I have Aastra 6731i SIP phones

All, I've fixed my problem getting Asterisk ooh323 channel to stay registered with my Cisco IOPS gatekeeper, now I need to get dialling working. I have the following: [Asterisk with ooh323] ----h323---- [Cisco IOS GK] ----h323---- [Radio system OpenH323] 192.168.1.5 192.168.1.6 192.168.1.7 the Asterisk box has numbers

Jan 19 10:00:29 VERBOSE [7177] logger.c: -- Executing [1000 at ext-meetme:7] Read("DAHDI/2-1", "PIN|enter-conf-pin-number||||") in new stack Jan 19 10:00:29 VERBOSE [7177] logger.c: -- <DAHDI/2-1> Playing 'enter-conf-pin-number' (language 'en') Jan 19 10:00:43 VERBOSE [7177] logger.c: -- User entered

Dear All, It seems that there is a bug on the ooh323 while using registering with gatekeeper. The gatekeeper is GnuGK and the problem is when the Asterisk recieves a call from the Gatekeeper and routes it back out to an SIP Phone. The call would be connected and immediately dropped after 1-2 seconds connection time. This doesn't happen when ooh323 module isn't registered to a

anybody successfully running asterisk-callmanager scenario with h323 trunk (ooh323 channel driver in asterisk)? I'm using 1.2.12.1 & ooh323 from 1.2.4 add-ons, but seems, that ooh323 is ignoring dtmf digits from callmanager h323 trunk setup with chan_h323 is working fine with dtmf I tried all possible modes with ooh323, but without success, with chan_h323, I'm using default (rfc2833)

Can someone tell me how I can configure ooh323.conf to accept call from h323 gateway (only the authorized h323 gateway) to my asterisk. I will be glad to know how this can be done. I tried the setting as in ooh323.conf [abcd] type=user context=default ip=62.193.1XX.2XX disallow=all allow=gsm allow=ulaw this gateway can make call, even if these lines are commented out and you restart the

Just a warning to people trying to use ooh323 with Asterisk 1.8.7. The example config file that comes with asterisk is called chan_ooh323.conf when it actually should be named ooh323.conf for it to work. Sent me into a panic when I was trying to install an H323 link to an Avaya server and the ooh323 module would not load because it could not find its configuration file. The file needs to be

Hello! I run asterisk 11.5.0 and I connect to some peer over ooh323. But there is alternate path to the same peer over sip, but this not we can usually use. So, if peer is not available over h323 I'd like to dial over sip. I tried to test this: iptables -D INPUT -s 192.168.6.0/24 -j DROP and do Dial(OOH323/${EXTEN}@peer,,g) but it waits forever. Is it possible to set signalling timeout

hello all i'm using ooh323.so module for my h323 connections and it works fine. i just have problem with loading and unloading module. you know, ooh323 module doesn't support reload command. it means, if ooh323 module is loaded and i reconfigure my h323 channels (add another channel), i should unload and load module again. it causes to disconnect all h323 connections which are connected

06.05.2015 10:58, s m ?????: Hello! I'm not h323 expert, may be somebody else can understand from this log what is happening, but I can't :-( Could you, please, provide log with tracelevel=6 in ooh323.conf ? Thank you! > hello Dmitry > > thank you for your reply. Ok, you are right. i want to configure trunk > h323 between asterisk 11.13.1 and 2800 cisco router. this

hello thanks Dmitry for your useful hints. i enable debug and solve my problem:). it was codec compatibility problem. but it is so strange; if i set codec g711alaw in cisco router and asterisk, i have the mentioned problem but if i set codec to transparent in cisco router, every thing will be ok. is there any difference between g711 codecs which cisco and asterisk utilize? On Wed, May 6, 2015

Hi, I'm trying to make ooh323 works with one asterisk box running 1.2.15 version. I can ring from a h.323 to SIP and SIP to H.323, but when the call is finished when the phone is answered. This is the log when I call from the H.323 device to a SIP device: Feb 23 10:57:32 VERBOSE[6096] logger.c: -- Executing Dial("OOH323/Telconet Mantaer-c5f8", "SIP/666|30|TtrwWC")

Hello all, I have seen some people asking how to configure asterisk to work with h323 but i did not manage to do fix it yet (i am not an asterisk expert). Can someone help me configuring asterisk? It is already compiled asterisk 1.4.5 with H323 support. Everything looks fine. Then i understand i need to configure several files: -sip.conf -ooh323.conf -extensions.conf do i also need to configure