similar to: 1000Hz kernel

Hi I am in the process of installing a new box and using dahdi. I have a tdm410 + hardware echo canceller. I have just read in the read me for dadhi that VPMADT032 support has been removed and unlike with the zaptel stuff i could just download and install the firmware I can't with dahdi what is the best way forward to recompile with hardware echo canceller support. Thanks Alex

Hi I have come across a problem, with my tdp410 and soekris board (basically pc on a chip amd geode cpu). I am using the box as a firewall/asterisk box. The problem occurs when I drop ppp and I get dead loop dectiotn going, I seem to lose interrupts and get lots of messages in syslog from wctdm24xx saying missed interrupt increasing latency its out lined here

I'm playing around with an ALIX 2D2 board (http://www.pcengines.ch/alix2d2.htm). It's a fanless, x86 system using an AMD Geode processor with 256MB of RAM. Also available are two network interfaces, two USB ports and one serial port (no keyboard or VGA). I'm using the Voyage Linux distro, which basically is Debian Lenny optimized for this board. Asterisk 1.6.1.12 runs fine on the

I''m running Xen on a dual xeon system at the moment and somehow the results are a bit less than what i expected. I’ve started to do some monitoring on it to see how bad it is. you can see for yourself on: http://core.zokahn.com/cs-01/ I''ve installed Xen 2.0 using the howto in howtoforge: http://www.howtoforge.com/perfect_xen_setup_debian_ubuntu This virtual machine is running 2

Hi recently bought a soekris net5501 and a tdm410 to place in there. I am having some issues attaching 12V power to the card via the molex card - basically the box for the motherboard is too small. I have read up about a PWR2400b and it seems to use 2wire pin, I am guessing to connect to P8 just behind the molex connector on the tdm410. can any one here confirm this, or have any info on the

Hi I am in the middle of move a small business over from legacy PABX + PSTN lines to VOIP infrastructure. I borrowed a spa9000 to place between the PABX and the PSTN lines. I have had this going for a while (>5 months) and it has been working fine (some issues with echo and other minor things), which is why I am moving to asterisk. I bought a tdm410 with 3 fxo + fxs. The fxs is connected to

Hello everyone, Does anyone out there have actual experience with running * on a mini-itx board from VIA? They look good, but I have some reserves because of VIA's problems with PCI latency in recent years (audio dropouts, wierd things happening). I am looking at the EPIA CL-10000. For $270, I can get a CL-10000 (1ghz C3, dual ethernets, etc), 256mb RAM, and a nice small (12 x 2 x 11)

Ok here is a real geek question, I building my own linux kernel for my asterisk system and came across the kernel setting for the timer frequency. I have one of 3 hardcode choices 100Hz, 250 Hz and 1000Hz. From what I understand the default Freq was changed from 100Hz in kernel 2.4 to 1000Hz (1KHz) in kernel 2.6. Timing is a BIG issue in asterisk with all the TDM and zap channel stuff.

playing with hdt on a soekris 4801, Im getting HUGE delays in cpu_detect. I added some timing code, heres what Im seeing ACPI: Detecting 0 mS in detect_acpi MEMORY: Detecting 0 mS in detect_memory DMI: Detecting Table DMI: ERROR ! Table not found ! DMI: Many hardware components will not be detected ! 55 mS in detect_dmi CPU: Detecting 0 mS in get_cpu_vendor 0 mS in "intel cpu

playing with hdt on a soekris 4801, Im getting HUGE delays in cpu_detect. I added some timing code, heres what Im seeing ACPI: Detecting 0 mS in detect_acpi MEMORY: Detecting 0 mS in detect_memory DMI: Detecting Table DMI: ERROR ! Table not found ! DMI: Many hardware components will not be detected ! 55 mS in detect_dmi CPU: Detecting 0 mS in get_cpu_vendor 0 mS in "intel cpu

I updated Asterisk to 1.6.2.7 and now the user introduction in the meetme application is no longer working: [May 27 09:26:51] WARNING[2407]: channel.c:4034 ast_request: No channel type registered for 'DAHDI' -- Created MeetMe conference 1023 for conference '800' [May 27 09:26:51] WARNING[2407]: app_meetme.c:3640 find_conf: No DAHDI channel available for conference, user

Hello there: I think I have a silly kernel configuration problem. I'm running: * vanilla 2.6.27.10 kernel built from source * dahdi-2.1.0.4 built from source So far so good, dahdi module loads just fine: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.1.0.4 when I try to: hal04 dahdi # modprobe dahdi_dummy FATAL: Error inserting dahdi_dummy

Quick and dirty question: for the TDM410P I must use the wctdm24xxp driver? Att Vin?cius Fontes Desenvolvimento Canall Tecnologia em Comunica??es Ltda.

Hi Got a new iphone, want to know about peoples experience with any apps that work well with asterisk and run on a iphone Alex -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 198 bytes Desc: Digital signature Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20091213/1f81f008/attachment.pgp

Hi, I need to run ztdummy for Paging, but now that this is all become dahdi I don`t really know where to start. I did build dahdi before building asterisk, but that`s it. I find it hard to find any documentation referring to dadhi instead of zaptel. I have no Digium hardware, but I still need the ztdummy timer (or whatever it`s called now). How do I get myself going? Regards,

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

Hi I am having some problems installing a paravirt RHEL guest on a deb amd64 xen machine uname -a = Linux debxen 2.6.20-1-xen-amd64 #1 SMP Tue Apr 24 22:23:22 UTC 2007 x86_64 GNU/Linux ============== xm info ============== host : debxen release : 2.6.20-1-xen-amd64 version : #1 SMP Tue Apr 24 22:23:22 UTC 2007 machine : x86_64

Hello my friends... We are having some problems with the fax in our asterisk server... We have: Asterisk 1.4.21.2 Zaptel Version: 1.4.11 libpri version: 1.4.5 Digium Card TDM 410P This digium card has 3 FXO ports and 1 FXS port where we have a fax machine connected! The problem is that we can receive fax very good, but we can't make any outbound fax call, in fact, our asterisk get freezed

Hi Kristian, Anywhere I can read about this Soekris/AstLinux project? ... Regards, Hans -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Kristian Kielhofner Sent: Thursday, February 24, 2005 6:02 AM To: jim@vanmeggelen.ca; Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users]

Howdy, I am playing around with asterisk within an LXC container on Ubuntu 11.04. I have asterisk (1.4.42) running fine, but want access to dahdi_dummy for timing (meetme). I have dahdi installed on the "host", and dahdi_dummy is loaded: root at astnorth:/# ls -ltr /dev/dahdi total 0 crw-rw---- 1 root root 196, 250 2011-06-08 13:59 transcode crw-rw---- 1 root root 196, 253