similar to: Fwd: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands?

Displaying 20 results from an estimated 1000 matches similar to: "Fwd: [asterisk-r2] MFCR2 With Unicall - can unicall affect zaptel commands?"

2009 Apr 08
3
Multi Frequency Cycle Timeout - E1-R2 METROTEL COLOMBIA
Hi, I have installed Elastix 1.5.2 (Barranquilla, Colombia (TELCO: METROTEL)) with a TE220P (2xE1) and TDM2400P (16FXS), openr2 is included in 1.5.2 version. The outcoming calls are ok, but with incoming call i have an error: ERROR*[*14972*]* chan_dahdi.c: Chan 2 - Protocol error. Reason = Multi Frequency Cycle Timeout, R2 State = Seize ACK Transmitted, MF state = Category Request Transmitted,
2007 May 14
1
Asterisk and unicall + mfcr2 signalling
Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14
2007 Nov 22
0
Vicidial + Unicall mfcr2
Hi Bruno, actually vicidial is working on top of asterisk, vicidial doesn't know what asterisk using in layer 2. SS7, ISDN stack, Unicall/mfcr2 is working with asterisk. vicidial uses asterisk application to deliver call center functionalities. Regards, Vidura. ================ Dear Bruno, I had the experience of using the Vcidial with the boards of Digivoice. It worked very well!
2008 Feb 18
1
mfcr2 stuck
Hello I'm using mfcr2 support (unicall) in asterisk 1.4. Everything is working fine, asterisk can answer calls. But after some random period of time mfcr2 module stuck. When I make a call to my * box I can hear only signal of getting caller ID ("tritirirti" - like jumping on :) ) and connection is terminated by my telecom operator. When everything I ok after few seconds of this
2005 Jan 18
2
MFCR2 - LIBUNICALL - Asterisk Problems
Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia (north africa). I have configure my MFCR2 according argentina R2 settigs : the test call run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2. generally in the begging no errors occur. after
2005 Jan 18
1
Asterisk - libunicall - MFCr2 *** settings problems ??? ***
Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors
2008 Feb 28
1
Unicall mfcr2 testcall issues in mexico outgoing:ok | incoming: fail.
-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 I have a astunicall-1.4 setup with a te110p to a nortel pbx in Mexico. (Hate R2!). This is what I get when trying to call to * box using testcall: ./testcall Chan 31, class 'mfcr2', variant 'mx,20,4', end 0, caller 0, from '' to '' Loading protocol mfcr2 Thread for channel 0 MFC/R2 Chan 31: Call control(9) MFC/R2
2008 Jan 30
1
Unicall CRN 32769 - far disconnected cause=Switching equipment congestion [42]
Dears, After weeks trying to contact support of my telecom about 'Seize Ack' because that is not returned, was a lock for make calls on my E1s. Now I receive back de Ack and get ready to make calls, but the technical support reports to me that my attempts to call do not send any digits to the oder site (telecom station). 8 seconds after start 'Unicall event Dialing' the line
2005 Jan 10
10
Unicall errors
If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN
2005 Jul 25
1
100% CPU with Unicall and * head
Hi all. When I place a call Im getting this error: Jul 25 09:50:07 WARNING[3200] channel.c: Exception flag set on 'UniCall/13-1', but no exception handler Lots of this messages appeared on my Asterisk full log and the CPU got 100%. Topology: Analog Phone - Hicom300H E1 - E1 Asterisk - IP Trunk Problem: 1. Calls from Analog Phone through Asterisk is ok, but the messages appeared.
2006 Apr 21
1
Unicall MFRC2 Problems with BrT.
Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no
2007 Jan 17
1
Asterisk + Unicall + Telmex E1 MFC/R2 Argentina + Meridian
Hi everyone! I'm having some issue trying to place calls with asterisk connected to an E1 R2 from Telmex Argentina. The other E1 port is connected to a Meridian which also uses R2 protocol. Calls sometimes fail with different error messages such as: Unicall protocol error 32773, 32772, 32769. Some other calls fail saying: Far end disconnected(cause=Destination out of
2005 Jul 28
0
Unicall Dialing problems
Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2
2007 Jul 27
2
Unicall/Dont know how to handle Accepted
Hi, I've finally got running Asterisk 1.2.14 with UniCall & MFC/R2 patches, I can generate calls and all seems OK but I cannot receive any call, this is what I get: MFC/R2 UniCall/3 <- 0001 [1/IDLE /Idle /Idle ] MFC/R2 UniCall/3 Detected MFC/R2 UniCall/3 Creating a new call with CRN 32769 MFC/R2 UniCall/3 1101 -> [2/DETECTED/Seize ack/Seize ack ]
2005 Aug 03
2
MFC/R2 Mexico Unicall Blocked
I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call
2007 Mar 19
1
Unicall Brazil
Hi. I am in the Brazil. I have a problem on Unicall for Asterisk 1.4. I am working with E1 with 30 channels. Message when it receives calls: chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772. My files: /etc/zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone = br defaultzone = br fxoks = 32-55 /etc/asterisk/unicall.conf: [Channels] language=br
2007 Jun 14
2
Unicall + MFC/R2 line dropped immediately after connect
Hi, I am trying to set up an E1 line with CAS signaling using available unicall patches with libmfcr2 implementation. Inbound calls works well, I am able to get DNIS and ANI from incoming call, but I am still not able to make an outbound call with our local carrier. After tweaking of protocolvariant parameter in unicall.conf I was able to find proper values for inbound and outbound calls, but
2006 Apr 25
1
MFCR2 in Brazil, someone?
Does anybody have a working Asterisk server with Unicall using MFCR2 in Brazil? Were having problems. It seems SPANDSP never detect the tones from the telco. Im using brazil protocol variant. Im having lots of problems to find out why spandsp seems to not detect the MF tones. We send the first digit, the telco says they receive it, and respond with the proper signal to ask for the next digit, we
2008 Apr 01
1
Unicall + incomplete DNIS on international calls
Hello everybody, i'm from Mexico, at the time i?m working on a production server with asterisk 1.2.25 + spandsp-0.0.4 + libmfcr2-0.0.3+libsupertone-0.0.2+libunicall-0.0.3 and zaptel-1.2.22. I installed this version of astunicall that i downloaded from http://www.moythreads.com/astunicall/ Everything works fine, i'm able to make outgoing calls and recive incoming calls with all ANI and
2007 Mar 16
1
Problems with MFCR2 and Meridian
Hi List, I'm trying to connect Asterisk with a Nortel Meridian using an E1 with MRFR2 signaling. I've connected both cards, and compiled all the required software... The problem is every call (outgoing or incoming) got dropped, complaining about some "T1 timed out" Only for testing purposes I'm using an application called testcall included on the lib-unicall package, and