similar to: T1/PRI ignore answer signal

Hi guys, I'm new to the telco game and still pretty new to Asterisk, although I've been using it for a couple of months now and like most of what I see. At my office, we've got a small two extension setup w/ two Digium cards for a single FXO line and three FXS extensions, but I'm also working on designing a larger installation for a customer which will involve ~16 analog

Could anyone with any experience with * over a non-PRI T1 help this newbie? I have a fractional T1 that is working fine through a channel bank, but I can't get any response on * using a T400P. My analog line and the extensions work fine, but the T400P port 1 shows a red led (what exactly does that tell me?). I brought up zttool which shows a condition red also, but ztcfg shows nothing amiss.

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

I have posted this to the Asterisk Forums, but got no response yet. Sorry if you are reading this for the second time. What fax hardware do I need for a T1? Ideally, I will switch my T1 to a digital PRI (not CAS I'm told, which is not as good) coming into the building. My CLEC said I can do this switch no problem. I have an analog T1 coming in now. >From the Asterisk box, I will connect

Hi all, Muppet from the UK asking for help We are just about to have a T1 line installed in our office in Dallas and "Advantex" the supplier has sent a questionnaire asking a number of questions. I have put the question area at the bottom of the email, we will be using Digium's hardware. could anybody help :-) In the UK when I asked for a E1, number of trunks required and the

Hello - I have a non-PRI T1 setup and have been making outgoing calls for several months no problem. I have Zapata.conf setup for fxs_ks on these channels. How do I take incoming calls on these same channels? Do I need to change the signaling? Any help is appreciated. Thank you, Dave -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm trying to hook up a non-PRI fractional T1 using a T400P port. The Telco says that it is provisioned as AMI with SF (not ESF) and that they are signalling by "sending down a straight DS1" (I'm not sure what exactly that means). They are also sending DNIS over these channels. I currently run it through a channel bank for my IVR application and it works fine but I am now

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Is there a way to make a call on a digital line T1/PRI and dont WAIT for the signalling back that the call was answered? I have a case where the T1 is working fine. I can dial work, numbers cell numbers etc... everything is fine. EXCEPT when I dial this internal trunk to access a PA system. The T1 is not telling me (in this case the line was answered) even though the PA system is giving dial

I'm ordering a PRI T1 for use with Asterisk and a Digium Wildcard TE405P. The provider is asking me a number of questions about how I want to configure the line. Here goes: 1. Dial Tone - No, Yes - Precise, Yes - SCC 2. Framing - SF, ESF 3. Line Coding - AMI, B8ZS 4. Signaling Type - Ground Start, E&M, Loop Start w/Ring, Loop Start w/o Ring 5. Pulse Mode - DTMF, MF 6. Outpulse Start -

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Ok, I'm about to take the plunge, and am trying to decide between Channelized T1 E&M and PRI. I'm getting an "Integrated T1" which will have data and voice capability, all plugged directly into my digium single T1 card. In either case the data piece looks pretty straighforward, just setup the channel properly, hand it off to the linux hdlc layer, and route away.... the

I am ordering T1-PRI service from local service provider and have a few questions. Is there framing and coding considerations (or is it all one standard), if so what is best? How are calls routed based on DIDs - are these just dtmf tones passed after the call is picked up and treated as normal exten=> definitions? John This e-mail was scanned and found clean by Monroe-Woodbury CSD

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Looking for someone with a successful experience similar to this; I have a need to cross connect a 3COM NBX PBX PRI interface to asterisk, but over a long distance. We do not need any IP connectivity and the solution requires G.711u audio so there is no benefit to using IP. Has anyone here successfully cross connected any PBX PRI interface expecting NI2 PRI signaling B8ZS/ESF with an

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

Hi, I have asterisk running a single T1 card with a connection to a nortel CS 1000. All calls to extensions, local and long distance are working just fine. My issue is this: The nortel CS 1000 supports connections to and intercom system that is just line level audio to speakers. When my PRI tries to call this "extension" it is never answered so my AGI never runs to play a message

When people call into my * box over the T1 interface, they get no ring tone. It rings the SIP phone and when the SIP user picks up, both parties can hear each other ok, its just the PSTN user calling in hears no ring. What could be causing this? I tried setting immediate to yes in zapata.conf, but that causes my DNIS and CallerID to stop being available. T100P with E & M Wink start

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do

I'm looking to install a system with 80 FXS analog phones. At this time the only cost effective solution is using a 4 port T1 card and addit 600 channel bank. Has anyone tried this solution? any good documents beside http://www.voip-info.org/wiki/index.php?page=Asterisk+hardware+channel+bank+check as far as i know, addit 600 T1 interface is not PRI (please correct me if i'm wrong) its CAS