similar to: PRI dropping

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

I have a PRI E1 link between Asterisk 1.4.24 and Alcatel-Lucent OmniPCX Enterprise R9.0. As EuroISDN it works fine. However, I need to move to QSIG because of a firmware upgrade on the Alcatel PBX which doesn't support EuroISDN (please don't ask why). Besides, I've read somewhere that 2 B Channel Transfers "should" work with * 1.4, the latest 1.4 libpri and QSIG. So this

Dear All, I am trying to setup an ISDN line from local telco on a digium card. The problem I am facing is that I am not getting any caller id from the telco. They say that they have enabled caller id. Please help me out. My zapata.conf -------------------------------------------------------------------------------------------------------------------- [trunkgroups] [channels]

Hi all, using latest asterisk-svn I want to reflect an video call incoming via an PRI EuroISDN channel to another outgoing PRI channel, and I want the the outgoing channel to have the exact same bearer capability < Bearer Capability (len= 5) [ Ext: 1 Q.931 Std: 0 Info transfer capability: Unrestricted digital information (8) < Ext: 1 Trans mode/rate:

I there, I have some trouble to do working caller id name for outgoing calls on the PRI we just installed. Caller id name work on incoming calls only. Caller id number work on incoming and outgoing calls. The provider, Goup Telecom, said that's in what i'm sending. They said that I send the cid name in ascii code and to do it working, I need to send it in hex. So I take some traces

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

I have attached my PRI debug out put when making an international call - hopefully it can shed some light on the situation. I am sorry if this attachment gets to the list twice, I sent one early this morning, but it has yet to appear - i may have sent that one in error. Kind Regards: Gabriel -------------- next part -------------- An HTML attachment was scrubbed... URL:

I have a T1 link from asterisk 1.2.23 (also tried with 1.4.13) to a Meridian Option 61C. Calls either way drop with error "Channel 0/23, span 1 got hangup, cause 100". Can anyone offer insight into the cause and solution/workaround? (I tried upgrading to Ast 1.4.13, and upgrading matching zaptel & libpri, put the problem is identical). For testing, I tried a call from the

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0

Hi, Is there a way to restart the DISA to the enter phone number? For instance, Bell Calling Cards let you hit # at any point which lets you enter another number to call. This is useful to reduce the number of digits dialed and to utilize per-minute calls. I was not able to find anything on the web. Thanks, -Ryan

Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running

Hello, I'm having problem connecting my Asterisk 1.4.29.1 with Digium TE420 to providers Cisco 2800 with VWIC-1MFT-E1 card. the same card runs fine with another E1 provider. TE420 led's lite green. Message type: RELEASE COMPLETE (90) < [08 02 80 ac] < Cause (len= 4) [ Ext: 1 Coding: CCITT (ITU) standard (0) Spare: 0 Location: User (0) < Ext: 1 Cause:

I've having problems with a BT 2 span ISDN-30/Digium TE205P asterisk setup with outgoing calls not completing and requiring an Asterisk reset to 'unstick' span 1. Sorry this is a bit long but I'm completely out of my depth :-( This system has been in use for some while and I recently upgraded it to asterisk 1.4.24, zaptel 1.4.11 and libpri 1.4.9. I didn't change

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

Hello, I am trying to diagnose an intermittent error when a call comes in over our PRI lines. The problem appears random, however I have feeling it has something to do with the call volume, as the frequency increases with more calls on the system. I am not an expert when it comes to reading the PRI Span Debug statements but here is a call that had a problem and I bolded, italicized, and

Hi all, I just configures my PRI and incoming calls are working fine but outside calling giving error PRI is BUSY :( any idea ? I have same setup on other box and that boxes works perfect. -- DAHDI/i1/6463279153-2 is proceeding passing it to SIP/7328-00000002 -- DAHDI/i1/6463279153-2 is making progress passing it to SIP/7328-00000002 -- DAHDI/i1/6463279153-2 is busy -- Hungup

Nik, This definitely helps! Please check your dial command. You've got "Dial(Zap/0/mynumber)" and I think you might possibly want it to be something like this: Dial(Zap/1/mynumber) or Dial(Zap/g0/mynumber) I don't recall there being a zap channel zero, but it is common to have a group zero. I would recommend trying Zap channel 1 - Dial(Zap/1/mynumber) - before trying the

Hi All, In my dialplan and standard asterisk CLI logging i see that i am able to restrict the callerid when dialing out with asterisk. however, on the receiving phone, the callerid is still displayed. When i increment the logging of the pri with "pri set debug on span 1" on the CLI i also get the lower level debugging info from the pri.

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.