similar to: SPA3102 - How to save config in a file

Does anybody know if the process of upgrading firmware on "Linksys SPA3102-NA" in Linux is the same as on Sipura 3K as described on voip-info.org http://www.voip-info.org/wiki/view/Sipura -- #Joseph GPG KeyID: ED0E1FB7

Hy all, Recently a have a little problem with a Cisco device, SPA3102. I use this device with asterisk to dial out with outbound trunk. (SPA3102 has 1 FXO port) It working ok , but the device SPA3102 do this : when a call is placed for outgoing in asterisk and send to SPA3102 , this device "answer and dial the number in the same time" , in my CLI I see the channel is open , but on

Hello, I've got an analog phone which is currently receiving unsollicited FAX calls from PSTN. For learning purpose, I'm preparing an Asterisk/SPA3102 setup that would let voice calls come in and out and translate incoming FAX calls to TIF files (forwarded through email)). My target setup is : PSTN <-- analog--> SPA3102 Line Port <-- SIP --> Asterisk <-- SIP -->

Hi list, After failing to get a Sipura/Linksys SPA3000, which I've configured as a PSTN gateway, to pass on the Caller ID, I decided to try my luck with a Linksys SPA3102 after hearing some promising stories. Unfortunately, I've run into a completely new problem: it seems Asterisk won't let this device register. I went about configuring the SPA3102 in much the same way as I

Hi All, In our small office calls to the PSTN are currently sent via Asterisk and a Linksys SPA3102 (1 x FXO and 1 x FXS): SIP Phone --> Asterisk --> Linksys SPA3102 --> PSTN If the PSTN is in use on SPA3102 I need a way to get the call to then route out over IAX termination. SIP Phone --> Asterisk--> Linksys SPA3102 --> PSTN (In Use)

Hello, i have a SPA3102 and asterisk v. 1.2.18. I also hev a mysql database with cdr. Well all I want is to receive incoming calls from pstn on specified sip account (suppose 8000), and to initiate outgoing calls from all my asterisk sip accounts through SPA3102 device. Someone can explain me what may i set on SPA and asterisk to do this thing. Thank you for your support. -------------- next part

Somebody has 5.1.7 firmware for SPA3102? I'm having issues with inbound/outbound calls using asterisk through SPA3102 with firmware 5.1.10. I've read it has a codec bug, since it doesn't care about what you set up in Preferred Codec. Any help will be appreciated. Sebastian -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm looking to build a VoIP solution for 100+ service vehicles that have WiFi hot spots installed (with cellular uplinks). Currently we are trying out Skype wireless handselts and Majick Jack. I'd also like to consider an Open Source solution that can bring the calls back to our data center [possibly integrated without our existing BCM 3.x VoIP PBX]. For hardware someone on the IRC

I need another Sipura 3K and the replacement I think is Linksys SPA3102. Any input on how reliable is it? -- #Joseph GPG KeyID: ED0E1FB7

Hi everyone, I'm trying to set up a VOIP mass deployment. To do so, I want to generate a configuration xml fails. I read somewhere that I had to use : http://<phone -or- device ip address>/admin/spacfg.xml but it work with an upper firmware only. My Software Version is 3.3.6(GW) The last firmware versin is 5.1.10(GW) Upgrade Enable: is set to yes on the linksys SPA3102 web interface

Hello list, this is my first post on this list. I have a server with Asterisk and a Linksys SPA3102 with 3 SIP phones. I have configured the SPA PSTN line as trunk to receive and send calls. I can call outside from SIP phone throw the PSTN line and all is OK, the problem is when I receive a call from the PSTN, on the out caller phone there is a demo playback. I want to redirect the call to a

Hi. I have a SPA3102 updated with with Software Version: 5.1.7(GW). I have this settings on Voice/Regional: Interdigit Long Timer: 10 Interdigit Short Timer: 3 Anyway, when hooking up (without dialing anything), the timeout starts after 3 seconds. It's like the Long Timer is unused. After dialing, the Short Timer is also used to timeout. Is that normal? Am I missing something? Thanks. --

I'm faxing from stand alone fax machine via linksys SPA3102 but most of the time only half or quarter page goes through. Did anybody have any experience like this? -- #Joseph

Hello. I've got a Cisco SPA303 that I'm trying to provision via http. I noticed that this device looks very similar to a PAP2T, so I used that as a template for my provisioning file. However, the result is less than stellar. Line 1 registers and works. However, lines 2 and 3 also register as line 1, effectively giving me a 1-line phone with 3 buttons. Also, the line name is the

Hi, I'm rather new to this domain so I may be doing stupid things without being concious of that. I've got a Patton MATA I'm trying to setup as T.38 fax adapter. Whenever I connect a fax machine (Dell MFP1815dn) or a phone to it, I can successfully send a fax or talk to the other end. Whenever I connect a fax modem (Dell Inspiron 6400 laptop), I keep getting "No signal. Line is

Hello, I could successfully played with General Purpose Parameters (GPP_A, GPP_B) and a TFTP server : whenever I change a GPP value in a configuration file, my SPA3102 automatically updates the corresponding value its web server shows. My config file is : <flat-profile> <GPP_A>myid </GPP_A> <UID1>myid </UID1> </flat-profile> I though I could use this

2009/12/15 Olivier <oza-4h07 at myamail.com> > > > 2009/12/15 Steve Howes <steve-lists at geekinter.net> > > >> On 15 Dec 2009, at 10:42, Olivier wrote: >> > Unfortunately, it seems macro expansion doesn't occur in Line1 tab : >> > when I type $A or $(A) or ${A} or $GPP_A or $UID1 in User ID field >> > (in Line1 tab), asterisk

Hi all, i need an XML file format which is used in remote provisioning of different spa devices. Please somebody tell me the format or tell me where can i find it on the internet. I also need a list of parameters which are configured using auto-provisioning. -- Best Regards Rizwan Hisham Software Engineer Axvoice Inc. www.axvoice.com -------------- next part -------------- An HTML attachment was

Hello to all Does someone knows how to force the Cisco IP phones (7940 and 7960) to reboot weekly or monthly? I think this would be useful because sometimes we change the configuration settings in the TFTP, but the phone just check the TFTP when he restarts... Thanks Jo?o

Hi, Is it possible to get the XML config off of a Linksys SPA-941 or 942 phone? I've tried http://[ip address]/admin/spacfg.xml however that file doesn't appear to exist. Thanks.