similar to: Asterisk analog DID with Adit 600

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

I currrently have Asterisk 1.2.8 with a TE110P Zaptel card tied to our Nortal DMS-10 switch via T1. This T1 trunk is configured for Feature Group D MF. The purpose of this is for LD delivery to a VoIP LD provider as a LD choice for our customers off of the DMS-10. When I sieze a channel on the zaptel, I get a spill of digits from the switch that is the called number, and I can see that in

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

Is it possible to control the dialing format used when making a call from asterisk separately from the inbound format? In my case I have a single robbed-bit T1 configured for featd (to receive ANI and DNIS) on a TE410P. This configuration works fine for inbound calls, however when an outbound call is made on this same T1 asterisk dials outbound in the featd format. I need asterisk to only dial

Hello All, I've mostly solved my DID problem from a few days ago. Apparenly the lines weren't configured properly. Now heres the next question. 12 E&M wink lines from telco. I have them all plugging into an Adtran 750 with FXS cards. The Adtran ports are configured DPO. How do I signal this from Zaptel. I have them setup E&M in zaptel.conf and EM_W in zapata.conf. They

Help. Why is it that I can call out from my GSBudgetone SIP phone but the audio is "one-way'? Why is it that when I call my asterisk phone number, I get a fast busy?

Hello, I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe. Our telco provider is giving us those settings: ESF B8ZF Inbound = E&M Immediate Outbound sig =Wink Start Yield to Glare = Yes Those trunks are using CAS for signaling. I have tried many configs/combinations in zaptel.conf and zapata-channels.conf In zaptel.conf, when having

We have 2 T1's coming from our phone switch to a digium TE220B. We have managed to get CPN and the extension outpulsed from the switch, but call setups are really slow. Our T1's are set up as E&M Wink, and they send us the last 5 digits dialed followed by the 10 digit calling party number (we couldn't get the switch to be happy with *CPN*+5* to use featd). We are using asterisk

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

To all Asterisk guru's... Here is my question. 1. Asterisk PBX - 5 Trunks / Incoming lines 2. 1 Building - 3 Companies (sharing phone system) Ok that's the basic layout. Here's the low down - Each company will have one dedicated channel for there company. The other 2 channels they want to be set aside as rollover's (rotary). That is not an issue. Where my concern is, how

We have an old Telrad 128KSU PBX to which I am trying to connect asterisk in the following manner: Current Setup: Telco-> T1->PBX Desired Setup: Telco-> T1-> Asterisk-> T1-> PBX. I am first trying to setup the Asterisk -> T1->PBX part without disturbing existing setup so I can get asterisk to forward calls to PBX and once that is done, I would try to move the telco

How do I setup my T1 card as an E&M tie line? Any special configuration? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20050523/8aac4dbf/attachment.htm

Hi, Can anybody with previous experience with it guide me on how to setup asterisk with analog e&m to connect it to an old style e&m system which uses 4 pair cables on RJ 45 jacks. All the analog cards I know of use RJ 11 jacks. And there is no choice of modernization of the customer equipment. Cable pin out are as follows: 1. M lead 2. E lead 3. Tip1 4. Ring 5. Tip 6. Ring1 7. SG 8.

Does anyone know the default E&M Wink timings for Nortel DID ports? The default settings on Asterisk are: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ;

We have 4 analog line and 2 analog trunks. On the trunks we have all the DIDs coming into the current phone system. Trying to get everything moved over to Asterisk but having issues picking up the calls on the analog trunk. We can receive calls on the plain analog lines and we can call out on all analog lines and analog trunks. When a call comes in on the trunk line the ZAP channels don't

I have a couple of live T1s sitting around and they are not ISDN(like most of the people that are using Asterisk seem to be using), they are regular old 24 channel, robbed-bit, E&M wink start, D4AMI T1 circuits. Can I get these T1s to work with a T100P Digium card and asterisk? Searching through the lists and the documentation I haven't seen any examples of how to configure this kind

I need to create a couple of tie lines between a legacy system and an Asterisk system. I was told that the tie lines are E4 Superframe E&M. I have done E&M wink but have no idea about E4 Superframe E&M and Google is not helping me here. Does anyone know about this type of signaling and if Asterisk can handle it? Thanks, Steve

Does anyone have experience with melding Asterisk with an older Executone PBX? I have a client whose existing voicemail server(repartee) has become bonkers and we need to stick a VM system in there asap. I thought asterisk would be a good thing to use. Does anyone have experience with the older Executone PBX's and asterisk? Any caveats, any tips, any things I should be aware of? Thanks,

I've been reading the Google searches trying to understand how to tie together Adit 600 to Asterisk to provide 2 way service. I'm about blind from reading. I assume, the answer is using MGCP between the boxes. However, the examples I found don't really explain fully enough to know how to modify examples to work for me. I'll have in the ADIT with T1's. There is a CMG and