similar to: SpanDSP question for Steve

You now need to compile and install SpanDSP-0.0.6pre3 at least (AGX has been changed). After you've done that - try AGX again. HTH -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Olivier Sent: 11 March 2009 06:16 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users]

Hi, With 0.0.6pre3: # ./build.sh CMake Warning (dev) in CMakeLists.txt: No cmake_minimum_required command is present. A line of code such as cmake_minimum_required(VERSION 2.6) should be added at the top of the file. The version specified may be lower if you wish to support older CMake versions for this project. For more information run "cmake --help-policy CMP0000".

hi,all i have just set up asterisk 1.6.0.7 rc1 with spandsp 0.0.5 pre4 to ReceiveFAX, link to a E1 (DE410P) using dahdi this can receive the fax from E1 successfully, but i see many error message in the log like this: [Mar 16 09:24:38] ERROR[23540] channel.c: ast_read() called with no recorded file descriptor. when i receive a 5 pages fax, i will see this error message over 200 lines..... it

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all, anyone else seen RX/TXFax crashing Asterisk on latest Asterisk SVN? I've now seen it on two machines I tried to set up - one it seems because the tiff file was malformed, but the other is doing: tiff -> tx fax -> zaptel -> pstn -> ddi -> zaptel -> rx fax -> tiff The above crashes every time. If no one else has

Hi, I am recently updated my asterisk 1.4.1 to 1.6.2.6 because of fax service. I have installed spandsp 0.0.5, then 0.0.6 pre 17 as well because to have support. app_fax is available in menuselect and loaded into my asterisk. The upgrade went without any problems. ast*CLI> module show like fax Module Description Use Count app_fax.so

Receiving a fax pstn - pstn with 1.6.2.6-rc2: -- Executing [s at incoming-pstn-line:1] Answer("DAHDI/4-1", "") in new stack -- Executing [s at incoming-pstn-line:2] Wait("DAHDI/4-1", "3") in new stack -- Executing [s at incoming-pstn-line:3] Dial("DAHDI/4-1", "DAHDI/g0,36") in new stack -- Called g0 --

JFYI - I run (successfully) agx-addons with 1.4.22 and Etch. Make sure you have the right version of SpanDSP installed (as well as the tiff libraries). -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Loic Didelot -->> Sent: 19 December 2008 20:33

Hi, I am using spandsp-0.0.4, tiff-3.8.2, and agx-ags-addon with Asterisk 1.4.18. Everytime rxfax executes, Asterisk crashes: -- Executing [fax at phones:1] Set("Zap/2-1", "FAXFILE=/var/spool/asterisk-fax/1207322398.0.tif") in new stack -- Executing [fax at phones:2] RxFAX("Zap/2-1", "/var/spool/asterisk-fax/1207322398.0.tif") in new st ack [Apr 4

Dear All, I'm having problem with spandsp/txfax, I'm not able to send a multi paged tiff file, the fax machine receives the first page of the document and complains about communication problem. The file what I'm trying to send has 2 pages and is received & generated by spandsp/rxfax. Searched in the archives, but found no solution. I'm using: Dell Optiplex PC Inoteska Quad

Hi, I've read README file in agx-ast-addons-1.4.17.5.tar.bz2 It says "Install libTiff >=3.8 and <4.0" Should you really use this agx-ast-addons to get app_rxfax and app-_txfax running with latest 1.4.22 ? If positive, should you take this libtiff warning into account ? If positive, where can you find such libtiff version as Debian repository (I didn't check alternate

I am trying to compile spandsp on my asterisk server, and it keeps failing out with the following t4.c:38:21: tiffiop.h: No such file or directory In file included from t4.c:41: spandsp/t4.h:62: error: syntax error before "TIFF" spandsp/t4.h:62: warning: no semicolon at end of struct or union spandsp/t4.h:63: warning: data definition has no type or storage class spandsp/t4.h:64: error:

2009/2/26 Olivier <oza-4h07 at myamail.com> > I must add I tried spandsp0.0.6xxx as a warning message advised me to do so > (using 0.0.4 would be ok for me but current trunk doesn't allow this > anymore, it seems). > > > 2009/2/26 Olivier <oza-4h07 at myamail.com> > > Hi, >> >> With 0.0.6pre3: >> # ./build.sh >> CMake Warning (dev)

I have googled until blie in the face, WiKi'd until physically exhausted and searched through every Asterisk repository that I can find, all to no avail... No matter which version of SpanDSP I use, with which version of libtiff, Asterisk, ... I simply cannot send faxes. I can receive faxes *perfectly* (sending from standard fax macine on POTS) into tiff file (via Digium analogue card),

Hi, I have problem installing spandsp-0.0.3pre24 on FreeBSD 6.1. I get error: configure: error: "Can't build without libtiff" . But I have installed tiff from port tiff-3.8.2. I understand that the problem is about libtiff, and spandsp can't find these libs. So how to fix the problem? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi everyone ! I have some aditional info on problem with TXFax and sending multi-page TIFFs. I have made 6 different multi-page TIFFs (Group3 1D with fillbits EOL aligned - 3 pages one TIFF in lowres and one in hires, Group3 2D -3 pages againg in both resolutions , and Group 4 - 3pages in both resolutions), and then tried to send them to Panasonic KX-F1100, Panasonic KX-F500 and SpanDSP

Hello all, I use Fedora 3, and I have compilation problem of SpanDsp , when installaing spandsp, tiff warnings and errors generated and libunicall generate "unresolved references....." Is the problem in my libtiff installation, spandsp.h or in tif_dir.h and tiffiop.h? Are tif_dir.h and tiffiop.h too old? The solution provided by ?HO SIN? to ?Kaws? : >>> recompile libtiff

Hi, Maybe I missed it while checking it, but which spandsp version is recommended to play with Asterisk 10 and T.38/T.30 gatewaying ? I can see both spandsp-0.0.6pre17.tgz and spandsp-0.0.6pre18.tgz here (http://www.soft-switch.org/downloads/spandsp/) but I couldn't find a changelog documenting differences between them. So I prefer to double check ask for recommendations. Regards

Sirs, I can't compile the source spandsp-0.0.2pre10; when i try to do the "make" sentence the following errors appear: # make Making all in src make[1]: Entering directory `/export/usr/src/spandsp-0.0.2/src' make all-am make[2]: Entering directory `/export/usr/src/spandsp-0.0.2/src' if /bin/sh ../libtool --mode=compile gcc -DHAVE_CONFIG_H -I. -I. -I. -I -g -O2 -MT

I have spandsp installed and working, but when it emails using Scotts mailfax, the attachment is a dat file. I tried to rename the file to .tiff or .pdf, but it will not open. In the /var/spool/asterisk/fax folder, that faxes are there as tiffs, and I can open those without any trouble. The problem is in the conversion from tiff to pdf. Is there another package that needs to be installed for

Hi, all. I've got app_rxfax going and nicely receiving a fax, which I then throw to a script, and have it convert it to a PDF and mail it. Works great... a lot of the time. But a fair bit of the time, rxfax throws errors, and extensions.conf seems never to invoke my script. Here are the pertinent lines: exten => _6403,n,rxfax(${FAXFILE}) exten =>