similar to: TDM400P Circuit/channel congestion problem

Displaying 20 results from an estimated 1000 matches similar to: "TDM400P Circuit/channel congestion problem"

2006 Sep 12
2
Patch-o-matic support
Hello, Is there is iptables and kernel package support for patch-o-matic? System: Centos 4.3 Thank you. Rgds, Asfihani
2008 Oct 20
1
Zaptel FXO offhook when connected to PSTN
I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*
2006 Feb 13
1
problem with outgoing calls Unable tocreatechannel of type 'ZAP' (cause 34 - Circuit/channel congestion)
When Asterisk first starts up, it will attempt to "bring up" the B channels on any PRI circuits. If you are using A@H then you can log on to the Asterisk CLI (asterisk -r) and then do "stop now" to stop asterisk. Start up Asterisk again by typing asterisk -cvvv at the Linux command line. You should see a bunch of messages on the terminal and then you'll get the Asterisk
2010 Feb 11
2
app_dial.c: Unable to create channel of type 'Zap' (cause 34 - Circuit/channel congestion)
Just to share some experience with everyone about what happened today to our Asterisk 1.4 box with Digium TE412P card. We had an unscheduled power outage which shut down the Asterisk box. When the power went up, Asterisk came back up okay but the ports on the card were all red. Zttool show red alarm and cat /proc/zaptel/1 show red alarm today. Both incoming and outgoing cannot be made. When a
2006 Feb 13
1
problem with outgoing calls Unabletocreatechannel of type 'ZAP' (cause 34 - Circuit/channel congestion)
Nik, I'm not sure that "NOP" is correct, but I'm in the states so I'll to defer to someone who knows E1/PRI. When I run zttool I have "OK" under the alarms. Is there a way you can call the telco and confirm the settings? Make sure that framing, coding and D channels are set up on their end the same way you're set up. As for asterisk, here's what I get
2006 Feb 13
0
problem with outgoing calls Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion)
hi i've configured a TE205P on asterisk at home this is my zaptel.conf span=1,0,0,ccs,hdb3,crc4,yellow span=2,0,0,ccs,hdb3,crc4,yellow bchan = 1-15, 17-31 dchan = 16 bchan = 32-46,48-62 dchan = 47 loadzone = it defaultzone = it and my zapata.conf signalling=pri_cpe ; pri_cpe = PRI slave ; pri_net = PRI master switchtype=national usecallerid=yes hidecallerid=no callwaiting=yes
2006 Feb 13
1
problem with outgoing calls Unable to createchannel of type 'ZAP' (cause 34 - Circuit/channel congestion)
Nik, Just curious - what is your telco setup? Do you have PRI with the specified D channels? You need to make sure that your telco is set up to have the D channels on 16 and 47. When you first start Asterisk, or when you log on to the CLI, do you ever see messages stating the B channels are successfully started? Let us know. -MC -----Original Message----- From:
2005 Aug 01
2
TDM400P REV I issues - ProSLIC vs TDM400P
The REV I card shows up in the PCI table as: 02:05.0 Network controller: Tiger Jet Network Inc. Intel 537 (or 02:05.0 Class 0280: e159:0001) Subsystem: Unknown device b119:0001 But the REV E/F shows up as: 02:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface (or 02:0d.0 Class 0780: e159:0001) Subsystem: Unknown device b100:0003 One
2006 May 09
2
Problems with TDM400P and FXO modules
Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output
2009 Feb 16
4
Faxing with asterisk
Hi All, I need to setup asterisk to receive fax. I'm try Spandsp (opensource) and Attrafax (commercial) both on asterisk 1.4.23) but the results are disappointing. with spandsp many times the fax arrives cut. with Attrafax i have some problem. Anyone have any idea or solution (Opensource or commercial) to suggest me ? Best Regards
2004 Oct 01
1
Re: Problem with TDM400P
Greetings all, I'm new to asterisk... Finally got two IP phones and two TDM400P's (one with four FXO modules and one with four FXS modules)... Began experimenting a couple days ago and have ran into a very aggrevating problem. My system consists of the following hardware: Abit BL7-RAID motherboard Pentium 4 1.6GHz processor 512MB SDRAM 2 TDM400P cards 2 3Com 3c905
2007 Jan 15
0
S110M (FXS) Modules no longer seen on TDM400P
I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when
2005 Aug 24
1
TDM400P : no dial tone...
Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker
2005 Jan 07
1
TDM400P - Segmentation fault - Help!
Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:
2005 Jan 06
1
TDM400P - Segmentation fault
Hi all, I'm trying to install a TDM400P card, and I need some help. Please, see below... after dmesg command: [root@voip root]# dmesg via82cxxx: board #1 at 0xD800, IRQ 5 Zapata Telephony Interface Registered on major 196 PCI: Found IRQ 3 for device 00:09.0 PCI: Sharing IRQ 3 with 00:10.1 Freshmaker version: 71 Freshmaker passed register test Module 0: Installed -- AUTO FXS/DPO Module 1:
2004 Oct 05
1
Non-working module on TDM400P?
Hi all, I was wondering if anyone had any pointers on how to determine whether or not a module has gone wonky on the TDM400P? I have a 2 FXO (channels 3 and 4) and 2 FXS unit (channels 1 and 2). The bad (?) module in question is the FXO module on channel 3. I can't dial in to or out of that channel; dialing in gives a busy signal, dialing out just shows * hanging around after attempting a
2005 Feb 07
0
TDM400P FXS works only if two lines are off hook?
I have a TDM400P with one FXO module and two FXS modules in it. I also have a Wildcard X101P. After trying hard to get things working on various Intel computers, but having echo problems that made it not really usable, I decided to try it on some older PowerPC (Macintosh) hardware running Yellow Dog Linux. Things started off smoothly. Both zaptel and asterisk seemed to compile okay, and both
2005 Oct 03
0
TDM400P recognised as "Network controller: Unknowndevice"
All the 'unknown device' means is that your 'lspci' doesn't know what the card is. That's all. Nothing more. --Rob ________________________________ From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Aryanto Rachmad Sent: Tuesday, 4 October 2005 7:43 AM To: asterisk-users@lists.digium.com Subject:
2006 Dec 13
2
TDM400P won't ring GM phone of mere 0.1B
This is rather bizarre: My TDM11 (one FXS) rings a $10 passive phone with REN of 1.0B, a cheap speaker phone of 0.3B, and a cordless phone with marked REN of 0.0B. But it couldn't properly ring this 27935GE3-B (FCC ID G9H2-7930) cordless phone rated at merely 0.1B. Rarely, the phone will crack out an occasional weak and abrupt beap, but never a normal ring. Otherwise Asterisk and TDM400P
2006 Jan 19
1
TDM400P zttest not working
Hi, I have a TDM400P running with only one FXO port running on a VIA EPIA MS10000 (1Ghz Via Eden). When I run zttest from Zaptel 1.2.1 it hang and when I interrupt it with Ctrl-C that is the result: ?anyone have some idea about why isn't working? Some additional info: # /usr/src/zaptel/zttest -v Opened pseudo zap interface, measuring accuracy... --- Results after 0 passes --- Best: