similar to: Voicemail message is dialtone

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

My outgoing FXO calls are answered but have no audio in either direction if I have callprogress=no in chan_dahdi.conf. If I change to callprogress=yes then the audio returns. My chan_dahdi.conf file is listed below. Can anyone point-out why callprogress=no isn't working? #cat /tmp/a [trunkgroups] [channels] language=en context=incoming toneduration=40 ;usedistinctiveringdetection=yes

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2

Hi All i'm using sangoma card. connected to E1, my wanpipe file as #================================================ # WANPIPE1 Configuration File #================================================ # # Date: Fri May 27 00:25:04 GMT+7 2005 # # Note: This file was generated automatically # by /usr/sbin/wancfg program. # # If you want to edit this file, it is # recommended

Hi I have recently upgraded my Asterisk system (from 1.2 to 1.4) and I have started to notice the following messages when I recieve a call on my Zap channel :- [Mar 11 09:20:17] WARNING[4294]: chan_zap.c:8851 zt_pri_error: 1 copying 5 bytes LLC I have a single PRI ISDN 30 link to a Siemens Realitis DX. Here is my zapata.conf :- [channels] echocancel=no echocancelwhenbridged=no rxgain=-5.0

I'm in the process of setting up a 'phone tree', and are running into some problems. My goal is for users to dial a phone number, the asterisk system picks it up, plays the greeting, and users can type whatever they want into the system. What actually happens is users dial the phone number, asterisk picks up and additionally goes off-hook on another line, plays the greeting and

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi, I've got a problem with my asterisk set up which has been going on for a while (months). I'm currently running 1.2.7.1 on a gentoo box with the topology below: +-----+ PSTN ---------+ * +------------- Service Provider (wctdm400p) +-+-+-+ IAX | | | | FXS --+ +-- SIP (cisco 7940)

Hello, I have a Nvidia Riva 128 ZX graphic card. But renouveau need the nvidia proprietary driver to work and there is no nvidia proprietary driver for Riva 128 or Riva 128 ZX. How can I send you informations that can help you to write a free and open source driver for this nvidia graphic chip. At http://users.tkk.fi/~jpakkane/ren/, I found nothing for NV3. But there is some information for NV1

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

i belong to india. i am making pbx using sangoma fxo card. i want that when ever call comes to my PSTN line i should see the no from where call is coming. so i have to configures chan_dahdi.conf according to my region. i checked dahdi.conf and in that they have mentioned for india

For what I know you can''t use the TM bundles... But like mgutz pointed there''s a lot of plugins. There is some alternatives to achieve something like TM bundles. Look at this links: - GMate - http://github.com/lexrupy/gmate/ (http:// alexandredasilva.wordpress.com/gmate/) - gedit-rails - http://github.com/mig/gedit-rails/ Think that GMate is the most complete. I use these as

Hi, I'm having trouble with dialing out on analog lines. Asterisk can't seem to detect "answers". I have two zap groups. Group 1 is connected to an external analog PSTN provider. This group seems to work fine, especially with "answeronpolarityswitch". Group 2 is a group of "GSM gateways", ie. devices that host SIM cards so that you can dial from any PBX

Hello everyone, I want to connect a fax to an FXS port (TDM420P). For testing purposes, I connected an analogue phone to it first. However, when I pick it up, I cannot hear anything at all. The power cable is plugged into the card, the port is configured to use fxo-signalling. Also, immediate=no. Here's the files: /etc/zaptel.conf: # Autogenerated by /usr/sbin/genzaptelconf -- do not hand

I am trying to get my xterm window under gnome to open with large fonts, with light green foreground and dark green background. I have the following .Xdefaults file contents: $ cat .Xdefaults ! This is a comment ;-) #ifdef COLOR *customization: -color #endif !! Let's cast a wide net, for any app supporting these ! Blink instead of beeping *visualBell: True *scrollTtyOutput: False

If I have a global variable in my dialplan and I change it, does that change immediately take affect for all calls that are active? Here is my situation. The company I work for has two office groups that share a building. The two offices are separate companies but support one another and want to be able to transfer calls as if they were all on the same phone system. Each company has 4

I'm having real problems with my connection to BT, it is a home line, but after a while it sets an alarm and only a restart of asterisk resets it could some one look at the below configs and suggest any changes to make this more reliable Thanks for your help Robb asterisk version 1.6.1.10 dahdi version SVN-trunk-r7445 dahdi_scan active=yes alarms=OK description=Wildcard TDM400P REV I