similar to: Digium TE220 supported protocol

hello, We encountered signaling problem with a french national carrier. They ask us, which signaling is configured on our single E1. I need to know if it's ETSI, VN4 or VN6. I know what ccs, and hdb3 mean but I do not succeed to make the link between the signaling type. I searched through RFC Q.921 and Q.931 It would be great to obtain some help. cedric

Hi: I want to have conference call with asterisknow and need 2 ports E1.Which Digium card is better?TE212 or TE220.I haven't problem with motherboard. Regards. --------------------------------- Get the Yahoo! toolbar and be alerted to new email wherever you're surfing. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hello folks. I've got a strange issue. When I modprobe TE220 I do not see mesages like Launching card: 0 <..> Setting up global serial parameters. You can see how I loaded and unloaded the card for several times - http://asteriskpbx.ru/pastebin/11 lspci can detect the card: 03:08.0 Communication controller: Digium, Inc. Device 0220 (rev 02) dahdi_hardware also: astpbx ~ # dahdi_hardware

hi folks. i have a Digium TE220 PCI-E 2 port T1/E1 controller installed in an IBM x3400 server. i load the wct4xxp driver seems ok. but when i execute "ztcfg -vvv" command. the kernel panic. i tried zaptel 1.2.21 & 22. they have the same result. following is my zaptel.conf: loadzone=cn defaultzone=cn span=1,1,0,ccs,hdb3 span=2,0,0,esf,b8zs bchan=1-15 dchan=16 bchan=17-31

Hello everyone. I have a timing slips errors and I can't understand what source of the problem is. My installation has 2 digium cards: TE420 and TE220 cards in one server. There are 3 spans (E1) to PSTN and 3 spans to internal PBS stations - normal installation for transit communication. Span configuration is: span=1,1,0,ccs,hdb3 #TE420 - first port. To PSTN. span=2,0,0,ccs,hdb3 #TE420 -

Hello, I just received a couple SX440isdn phones and was wondering if they can be plugged into a Diva 4BRI port in NT mode and work with asterisk+chan_capi? I know they probably work fine with mutliHFC cards with either bristuff of chan_misdn but since I have some spare Divas, I was curious about their potential as phone ports. The Diva's 3 and 4 ports are already set to NT mode at boot

I am having a problem with a new PRI turn-up on dahdi 2.5.0 and asterisk 1.8.5 that I have not seen before. The PRI is setup as B8ZS, ESF and the span shows up and ok. This PRI is merely a crossover T1 going into an old DC0 class 5 switch. I am getting the following errors over and over again [Aug 16 10:26:10] NOTICE[8002]: chan_dahdi.c:3043 my_handle_dchan_exception: PRI got event: HDLC Bad FCS

Hi All, I've bought a R2Adapter to convert R2Digital to ISDN. I am trying to config E100P card but D-Channel is down. I know R2Adapter uses ETSI ISDN Protocol so I tried unsucessfully setup switchtype to EuroISDN. Any clue? Daniel

So historically I've done one of two things on systems where I've needed to use MeetMe * used a real Digium card, and I've only ever used a TE400 or a TE420 for that purpose, and I know they have the timing chip * used dahdi_dummy, which works well with light load, but I had it running on a very overloaded server and had audio quality issues. I may have had quality issues even with a

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

Hello! At the end of year 2013 I had problem on my supermicro system with TE133, namely it losted connect to another system. So I opened case and finally card was replaced by TE220. Now I need to buy another 1 port card for almost the same supermicro. Could somebody tell me is this problem resolved? Thank you!

I'd be grateful if anyone here could comment knowledgeably on an idea that I have had, as to whether it should be possible or not. Consider two Asterisk boxes, each with one or more E1s on EuroISDN. Each box has a different telephone number that hunts across all its E1 channels. In addition there is another number that hunts across all the channels on all the boxes. A call comes in to one of

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

Dear list, I am playing with Sipura 3000 since last week. Through the wiki pages I could get running it reasonably well. My setup is that of a Sipura, linked with a local analog cordless phone, a local PSTN line and the setup to link to an asterisk server located at a remote static ip address. I can dial the cordless phone from other extensions located at the asterisk server; I can dial out

Hi, since version 1.4.12 the libpri package supports ETSI Explicit Call Transfer feature: http://downloads.asterisk.org/pub/telephony/libpri/ChangeLog-1.4.12 Does anyone know, how to use this feature in the dialplan? I can not find any hints in the asterisk doc. Best regards, -Thorsten-

Where can I get E1 and/or Euro-ISDN specifications/data sheets? Are there specs for other E./G./Q./etc. protocols as well? Thanks!

Hi does anyone have a definitive list of countries other than those listed on the wiki which are supporting app_SMS on landlines using ETSI ES 201 912 ?? Thanks Tim Robinson Basingstoke, UK

hi, i have the problem that i'm not able to set and receive the Service Indication (SIN) from our E1-PRI and from our ericsson BP250. The problem is, that the Bearer Capability (BC) together with the High Level Compatibility (HLC) and Low Level Compatibility (LLC) forms the Service Indicator (SIN). The SIN is used to determine if the call is voice, fax or data. It's essential to set

Hi I wonder whether anyone got the Sipura ata 3000 to decode British Telecoms callerid and pass it to asterisk? The userguide seems to suggest that this is not possible, is that right? Conrad