similar to: ISDN - BRI

I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1 Anyone was able to use this card with asterisk? I couldn't find much information about it. Any help?

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi Guys, I got 2 internal HFC-S[5] (not sure what character this is) internal modem cards yesterday, thought I would get different makes as the one was a named brand, the other not... but anyway... Its picked up by lscpi as a ... "Network Controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02)" I'm using kernel 2.6.10, and I saw I must use CAPI. I

Hello, I am having problems, getting my asterisk-domU to work properly. It consists of the following components: - Debian Etch under Xen-3.1 with a 2.6.18-kernel - Asterisk 1.2.24 - mISDN-1.1.5 I have 2 HFC-ISDN-cards, which I pass through to the Asterisk-DomU in permissive mode. This is working fine. The strange problem is, that the two HFC-ISDN-cards are not beeing initialized by the

Hi all, I have a "Cologne Chip Designs GmbH ISDN network controller" and I want to terminate voip calls via this ISDN card. My question is: How I must to wire the ISDN equipment with my ISDN card? With normal cable or crossover? How I can to check if ISDN card is linked with ISDN equipment? In this moment I have 1:1 cable between ISDN's, the mISDN is installed and "misdn

Hi all, did somebody successfuly export ISDN Cards to DomU? I want to have 2 ISDN Cards in DomU (for Asterisk with mISDN) lspci -vt -[0000:00]-+-00.0 nVidia Corporation MCP55 Memory Controller +-01.0 nVidia Corporation MCP55 LPC Bridge ... +-05.1 nVidia Corporation MCP55 SATA Controller +-06.0-[0000:01]--+-00.0 Cologne Chip Designs GmbH ISDN

Hi to all, I am searching to make work an Asterisk, with an ISDN card with Cologne Chipset. Here is the lspci: 01:09.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus master, medium devsel, latency 16, IRQ 5 I/O ports at c400 [size=8] Memory at fdefd000 (32-bit,

Hi, Can I use a simple HFC PCI (Cologne chip) card with asterisk 1.6.x ? What drivers are available? Thanks,

> having two NICs on the same subnet I'm trying to wrap my brain around that in the larger network picture. Two NICs in the same subnet (presumably on the same computer) would have access to the same other devices. This could potentially increase bandwidth (maybe?) and offer redundancy (if NICS, wiring or switches were the biggest source of failure). I'm not sure how the OS would

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hello everyone. I need a BRI ISDN card that works in Romania. I already have one of the "Cologne HFC-S" PCI cards and it doesn't work right, it's junk. I get waaaay too much echo using it. I'm now "shopping" for a better card. Can anyone recommend me a card that "fits" the following: (a) Costs less then $1000 / 750 euro (b) Has one or (preferably) two

Hi all, I have a cologne chip card which is connected directly to the ntba. Outgoing and incoming calls work fine, but incoming calls from ntba have the wrong callerid (first 0 is missing). I'm using current jolly misdn drivers and chan_misdn-14_04_05 with asterisk stable. Is anyone seeing this behaviour too? Thanks in advance Christian

hi i am experiencing some problems with the configuration of an BN8S0 Beronet card. I've downloaded last CVS of mISDN ans mISDNuser, i patch the kernel 2.6.16.18 and the enabled the following: <*> ISDN support x x Old ISDN4Linux ---> x x --- CAPI subsystem x x <M> CAPI2.0 support x x [*] Verbose reason code reporting (kernel size +=7K) x x [*]

Hello! I'm still wondering, how to park a call with an ISDN line. The setup is the asterisk server only, controlled via the CLI. I can originate a call and I can tell asterisk to start the JACK application. But I can't then park the call. I tried it with sending DTMFs with misdn send digit, no luck. I had a look at the CLI, but didn't stumble upon a command to park the call.

Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom