Displaying 20 results from an estimated 30000 matches similar to: "Asterisk-Panasonic TDA 600 error"
2005 Mar 10
7
Panasonic TDA200 E1 -> E100P negotiation issues
Hi, I hope someone can help me with this....
Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed
Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2
System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling.
Here is the situation.
The TDA E1 card is set in cross over mode and I am using a functional
2004 Mar 30
9
Zaptel/PRI problem
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi.
I'm getting the following error at random intervals on my TE410P with Asterisk
CVS-03/30/04-11:49:01-CEST.
I have two spans active, one connected to my Telco, the other to a Siemens
PABX. Both spans display this behavior at random intervals.
All calls are dropped when this happens. Spans are not necessarily in use when
this happens.
2005 Oct 12
1
Problem with PRI and Ericsson AXE 10
Hi everyone,
I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem.
First the PRI didn´t work (I got the TE110P alarmed with red). After
2006 Oct 19
3
Bristuff qozap drivers problem
Hi,
For a significant time now (since about 0.2.0-rc8n) the qozap driver
has become very verbose if an ISDN line is not connected... I get the
messages below every couple of seconds in the asterisk logs.
The "flaw" in the messages is the "Alarm cleared" message - The alarm
cannot possibly be cleared because there is no physical media
connected into that port!!! (BTW - All
2005 Aug 02
2
Channel Bank Help Please....
Hello -
I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I
am not able to call the FXS extensions or get dialtone on them. The
channel bank is connected via a T1 crossover to the cable and lights
show green. I really need to get this functioning by end of day. If
anyone can help me out I would be greatly appreciative.
Thanks,
Dave
zaptel.conf
loadzone =
2003 Mar 13
1
E1 yellow alarms
About every hour I see the yellow alarms on all or a number of channels of
my PRI which is connected to the dutch telephony network, Asterisk keeps
on working fine....
Here's an example where channel 1-24 went into alarm:
WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected
alarm on channel 1: Yellow Alarm
WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):
2006 Mar 31
2
PRI issues
Hi everyone,
I have been having some problems lately with our PRI and Asterisk, or
maybe it is just me. It happens once maybe twice a day, but when some of
our customers are calling in, the phone just drops on them. I pulled the
information below from the log from one that happened. I notice why it
is happening, but I can't seem to figure out a way to stop it from
happening. I also
2006 Dec 28
1
TE110P with Qsig
Hi all, as good?
I am trying to go up a board TE110P with link E1 ISDN PRI to establish
connection with a central office Siemens HiPath 4000. But I am having the
following errors:
Server1:~ # asterisk -r
Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others.
Created by Mark Spencer <markster@digium.com>
Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'
2007 Nov 20
1
Problems with losing D-Channel on
Hello all,
I got a problem at an asterisk server, with dropping calls, losing all
channels and reaktivating all channels and beeing back up.
This problem seems to occure randomly over the whole day, when it gots
traffic on the card.
After looking @ google I found several hints but none did work fine.
To avoid problems with the phone line (german E1) I called the provider, he
did a 45 min. route
2009 Mar 26
2
PRI dropping #2
Hey,
I wrote yesterday about PRI dropping, which turned out to just be a
regular reset of unused B-channels. This time there's a real issue. As
noted earlier I have an ISDN-30 connection, a Digium TE-121 with
VPMADT032 echo cancellation. These are my configurations files:
== /etc/zaptel.conf
loadzone=dk
defaultzone=dk
span=1,1,0,css,hdb3,crc4
bchan=1-15
dchan=16
bchan=17-31
==
==
2008 Oct 20
1
Zaptel FXO offhook when connected to PSTN
I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having
an annoying issue with the FXO ports. As soon as I plug either one into the
phone line it's as though the line is disconnected i.e. get disconnected
tone when trying to dial out, line is busy when dialling in.
The CLI shows the following:
trixbox1*CLI> zap show channel 4
Channel: 4
File Descriptor: 18
Span: 11*
2007 Feb 07
3
Red alarms
Asterisk is getting red alarms on my T1, sometimes once or twice a
day, but today it happened 5 times. Even once is too many. Every
call in progress is dropped. Please help! What do I need to do?
What can I try? I've googled and searched this list and can't find
anything. Here's an example from the logs:
Feb 7 13:37:54 WARNING[32451] chan_zap.c: Detected alarm on channel
6: Red
2009 Mar 31
1
PRI problem
Hi guys,
I've been trying to get my ISDN-10 line up for the past few days, but
its been going up and down. I am using OpenVox D110P card on
asterisk version 1.4.21. It seems to me like a cable problem. I tried
using Ethernet straight cable (12, 45, 36, 78) and also a "straight"
cable where the twisted pairs are on 12, 34, 56 and 78. The problem
remains the same.
2006 Mar 01
3
my zap channel not ringing
I need your help
I have a sangoma A104D on my dell server; I got card status ok with no alarm
If I dialed the extension 6210006, it shows the output as stated below, but
there is no ringing from the pstn number nor the iax softphone am using on
my pc.
I will be glad if someone can give me a working config?
What I want to achieve is to send all my call to the pstn on A104D?
The pstn am
2007 Feb 06
1
yellow alarm after weeks without trouble
Hi list,
I'm getting an error on a E1 link to the telco, after some weeks of
operation without trouble.
I have an asterisk with a TE405 in passtrough mode: two E1 are connected
to the Telco, two E1 are connected to 2 Siemens PaBX. Only 15 channels
are used on each E1 (conf is attached).The system has been in production
for nearly a year, and does work flawlessly for weeks, then I
2004 May 31
5
D-Channel Problems
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Good day eveyone,
I'm hoping that someone can help me. Perhapps i'm overlooking the obvious,
in truth, I hope that I am. I've scoured the mailing list and google,
and haven't come up with much.
I have a Digium T400P thats been connected to a channel bank for testing
for some time now. all has been well.
I've now just had
2006 Apr 10
3
E1 PRI problem with TE205P
Hi all,
I've setup a PBX in production environment last week but we have immediatly
find out drop conversations and lot of errors (in asterisk logs) like:
Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad
FCS (8) on Primary D-channel of span 2
My configuration is:
Motherboard: SuperMicro P8SCT (Intel E7221 chipset)
Hypertrading and APIC enabled
CPU: P4 3GHz
Digium TE205P
2003 Dec 10
1
Errors after re-plugging T1
Hi,
After temporarily pulling the T1 cable out of our Asterisk box, we ended
up getting a strange error messages even after the cable was plugged
back in.
[...]
Dec 10 09:01:11 WARNING[1192437440]: File chan_zap.c, Line 5683
(zt_pri_error): PRI: Read on 63 failed: Unknown error 500
Dec 10 09:01:21 WARNING[1192437440]: File chan_zap.c, Line 5683
(zt_pri_error): PRI: Read on 63 failed: Unknown
2004 Apr 12
5
T100P / ZAP / PRI errors
My PRI is being reset at least once a day with the following errors in the
logs.
zaptel, zapata, libpri, and asterisk are from CVS this morning.. This has
been happening for weeks on all versions (including -stable).
the T100P card appears to NOT be sharing an IRQ.
xenon# cat /proc/interupts
CPU0
0: 1203977 XT-PIC timer
1: 3 XT-PIC keyboard
2:
2008 Jan 29
1
PRI Alarms, Comes Back, But Asterisk Won't Touch It!
Here is the scenario: Asterisk 1.14.13; zaptel 1.4.6; Digium TE120P
(same problem with various previous versions; same problem with
different TE120P cards).
The customer has a partial (10 B-Channel) PRI that when it is busy
(eight or more B channels in use), tends to fail as shown below...
[Jan 26 23:00:31] ERROR[31893] chan_zap.c: Write to 28 failed: Unknown
error 500
[Jan 26 23:00:31]