similar to: CDR accuracy

Hi! What are the typical ways to work around the 64 groups limit? thanks klaus

Hi! I've went through the READMEs and could not answer this question: During installation, the Setup program asks: Would you like update/upgrade wanpipe drivers? (y/n) For a pure Asterisk TDM installation - is it required to patch the kernel or is this only when using the sangoma cards as WAN router? regards klaus

Hi! Is it somehow possible to evaluate the SIP response code inside the dialplan? I have an Asterisk server which forwards requests to various PSTN gateways with SIP. If the Dial() attempt is not successful I want to differ at least these 3 options: - called destination is busy (486): e.g. activate auto-redial - called destination does not exist, unassigned number (404) - gateway is broken,

Hi all, Is it possible to install more than 1 asterisk in a single server? If yes, what do I need to set and take care? Rgds, ango

Can someone tell me what I am doing wrong? Why doesn't CDR(duration) or CDR(billsec) return the correct values? cdr.conf endbeforehexten=yes extensions.conf [macro-Dial] ; ${ARG1} - Dial String exten => s,1,Dial(${ARG1},,M(post-dial)) exten => h,1,NoOp(Call was hung up - ${CDR(duration)} seconds long, billed for ${CDR(billsec)} seconds) The log shows: -- Executing [h

Hi! I just found out that Asterisk (1.4) does not write CDRs if the incoming call was not forwarded but handled internally without answering the call. E.g.: [from_pstn] exten => 997,1,Answer() exten => 997,2,Playback(tt-weasels) exten => 997,3,Hangup() exten => 999,1,Playback(tt-weasels|noanswer) exten => 999,4,Hangup() For incoming calls to 997 a CDR will be written, but not

Hi! Since some time the download of the newest Asterisk does not contains the version number anymore, but is just called "asterisk-1.4-current.tar.gz" This gives me a tarball where I do not know the version without looking into the tarball. Thus, IMO it would be very useful to switch back to old schema war the download contained the version number. Thanks Klaus

Hi! I have the following problem with Asterisk 1.4.23: ATA w/ T.38 Asterisk ATA w/o T.38 --------INVITE--------> --------INVITE--------> <-------200OK---------- <-------200OK---------- --------ACK-----------> --------ACK-----------> --------INVITE

Hi! I am looking for a tool (application or webinterface) which shows me the current status of an Asterisk server, e.g.: - Status of the SIP peers (registered/offline) - current incoming and outgoing calls - start-time, numbers, some history - history (calls stopped in the last 15 minutes, who hang up?) - should be possible to link those calls to the relevant SIP peers -

Hi! All the AEL examples have a semicolon after the closing curly bracket, e.g: context test { 1 => Hangup(); }; but without ; it works fine too, e.g: context test { 1 => Hangup(); } So - what is the reason for the ; after the closing curly bracket? thanks klaus

Hi! I use the following condition: if (${FOOBAR}=YES) { ... } The problem is, that if FOOBAR is not defined at all Asterisk generates a warning: WARNING[11982]: ast_expr2.fl:407 ast_yyerror: ast_yyerror(): syntax error: syntax error, unexpected '=', expecting $end; Input: =YES Of course I could use the following code, but this bloats up the code: if (${EXISTS(${FOOBAR})}) {

Hi! I have a setup with Asterisk in front of a PBX connected with ISDN to the PSTN and to the PBX. This Asterisk (a old 1.2 instance) is doing ENUM for outgoing calls and allows incoming calls per SIP. Recently the IP connectivity for this location was down the whole telephony was down too - not even incoming calls did work. This is really strange as incoming calls from PSTN are routed

Hi! I wonder why users.conf generates a SIP user and a SIP peer? Why is it not possible to set type=... in users.conf? (Asterisk 1.4.22) thanks klaus

Hi! IIRC there was an announcement some time ago that it is possible now to make conferences without the need for DAHDI anymore - but I can not remember the name of this feature anymore, and google didn't solved my problem. Thus, any references to this new system are appreciated. thanks klaus

Hi All; I am facing a problem that always the users confused and connect the telephone line coming from the telephone service provider to the FXS port and cause it to be damaged, specially if the card was 2 fxs and 2 fxo, so they make mistake and connect the line to fxs while it should be connected to fxo. What is the solution for this disaster? Regards Bilal

Hello! i'm trying to set up transfer without using the respective asterisk-function but with the built-in phone functions. my goal is to have the first callleg billed to the caller and the second callleg to the callee, who is responsible for the forward(and i can't bill a unknown caller anyways) so far it's working without problems, but my cdr's are messed. with the help of the

Hi! I want to use Asterisk as load generator to test quality degradation with increased load (e.g. testing other SIP equipment or IP-links). Is anybody aware of such a setup with Asterisk - is it possible to get RTP statistics out of Asterisk (e.g. jitter, packet loss, reordering ...)? Thanks Klaus

Hi! What is the preferred way to make database lookups from within the dialplan? I only know the MYSQL function from asterisk-addons. Are the other methods too? (e.g. for postgresql, unixodbc) thanks klaus

Hi, in dialplan -Asterisk 16.2 from Debian Buster- we have  same = n,Dial(PJSIP/101&PJSIP/102&PJSIP/103,15,tT) If thew call is not answered after 20 seconds, we launch a new dial with same and/or other extensions  same = n,Dial(PJSIP/101&PJSIP/104&PJSIP/110,20,tT) Looking in CDR we have at the end of the call (here we called 3 extensions which where ringing, let say 110

Hello all: I upgraded to 1.4.3 last night and use MySQL for CDR. I have noticed that 1.4.3 seems to log a lot of "crap" to CDR that 1.4.2 did not. I use a few macros in my dialplan to handle outgoing calls (lcr type stuff) and in addition to the proper CDR for the call itself I also have records to 's' in the same dest-context and entries to 's' in the default context.