similar to: SPA 3102 disconnect tone setting for China

Hi, I have a Linksys SPA 3102 using as ATA. The call routing is : Phone -> PSTN -> SPA 3102 -> SIP Proxy -> Asterisk The problem I am having is that when the phone hangs up, SPA 3102 can't detect it and relay the CANCEL message. Is this problem with my SPA 3102 config or it just works like that by default? Thanks in advance for your help. Regards, Mark -------------- next

Hello everybody, I'm a new user of * and I just bought a Sipura SPA-3000 to make a home voip installation. I actually have a problem when a PSTN user calls and hangs up. The disconnect tone is not detected by the SPA, the the call continues and, for example, leaves an empty message on the voicemail before hanging up (because * hangs up). How could resolve this problem?. I set, Detect

Hi, I have a SPA-3000. My telco sends no disconnect indication whatsoever, so I am having trouble making the PSTN line detect disconnect. What I want it to do is detect the very loud off-hook tone that is generated about 20 seconds after disconnect. It's not perfect, but it's a lot better than silence detection. I noticed that the zaptel drivers can detect this with busydetect, but

Sorry, I am resending this, I tried earlier, but I couldn't see it appear on the archives - apologogies if it appears double! -------------------------------------------------- My Sipura 3000 ATA died on me this morning. I had a Linksys SPA 3102 available which I would like to use as a replacement. Unfortunately, the SPA3102 is not able to register with the asterisk server - I am

I've read alot of comments on the SPA-3000, many if not all saying they had echo issues, but I've not seen anyone comment on the SPA-3102. Does anyone have any comments or issues with these? Tim

Hi to everybody, I have an spa 3102 where i connected an analog phone (in the fxs port) and the pstn line (in the fxo port). This is my problem: the incoming call doesn't arrive to asterisk. In the spa web page i configured this dialplane: (<:line01@192.168.1.220:5060>) where line01 is the context in sip.conf, 192.168.1.220 is the asterisk ip and 5060 is the asterisk sip port.

hi folks. does any one have experience setting up E1 PRI in Shanghai, China? it works fine when we use SIP phone to dial out, however when using forward function on the same phone, it seems like it's dialing out but there's actually no respond from the phone company (China Telecom) and eventually the dial command will timed out. here's our PRI portion of zapata.conf:

Dear Expert, I am stuck when trying to register SPA-3102 on AsteriskNow .. could any body please advise .. where can I find the article for doing this? .. I googled but got nothing.. Regards bie -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071203/6bbbecd8/attachment.htm

You can even set it to zero. Mine works well when in zero. The line pick up immediately :> -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Chris Stenton Sent: Thursday, February 09, 2006 6:57 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] SPA-3000 VOIP-PSTN

I have a linksys SPA 3102 with a DECT phone connected into its Telephone port. It has been working, but something I've done (and I don't know what) means that now everytime asterisk tries to dial it, it says it is busy. I can make calls from it through asterisk I am at a complete loss to know what to try next to fix it. Any ideas? -- Alan Chandler http://www.chandlerfamily.org.uk

Anyone tried the new PSTN/FXO port in the new SPA 3102 FXO/FXS adapter ? From a quick test (got mine yesterday), seems like it is not recognizing Caller ID from PSTN/FXO port.. Using the same configuration as a Sipura 3000 (to be sent to mother-in-law POP :-), no Caller ID at all, (I've even extended the PSTN delay to give it more time, but no dice). www.voxilla.com forum has a couple

Good morning, I've been having some problems getting the SPA-3102 working properly in India. Specific problem is that calls from the Asterisk server out the FXS port is failing. When trying to make calls, I'm getting this message: [Jan 26 23:00:31] NOTICE[2136]: chan_sip.c:13774 handle_request_invite: Call from '' to extension '66200' rejected because extension not found.

Hi to everybody, I need some help in configuration of the spa 3102. I created an account for line 1 (user 208, sip port 5061) correctly registered in asterisk, then i create an account in sip.conf like this: [general] register = line01:pwdsipura:line01@192.168.1.222:5060/095377078 [line01] username = line01 fromuser = line01 secret = pwdsipura host = 192.168.1.222 fromdomain = 192.168.1.222

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

I dont recall the SPA-941 playing a stutter tone in the previous firmware but it is driving me nuts, anyone know where to turn it off? Kerry Garrison Director of Technical Services Tech Data Pros - Orange County's Mobile IT Service Provider (949) 502-7819 x200 - <mailto:kerryg@techdatapros.com> kerryg@techdatapros.com <http://www.techdatapros.com/> http://www.techdatapros.com

hello my friend has the proxy set up his extention set up his password set up but he isn't getting a dial tone is there a second setting we need to put the address in? he is going to advenced settings line1 and in the proxy address box he is putting the info in below is the way he has it set up Sipura SPA Configuration Sipura Technology Inc Info System SIP Provisioning Regional Line 1 User 1

Greetings, We are currently testing a Sipura SPA-3000 as a gateway from our Asterisk system to a PSTN line for 911 access. We have a number of locations and want to place an SPA-3000 in each, connected to a PSTN line that will provide the correct ANI/ALI information to 911 for each location. It all works great, except for a reasonably significant (4 seconds) delay between when the SPA-3000

Does anyone know if it is possible to use the following disconnect tone setting with an x100p card? Disconnect Tone: 350@-19,440@-19;4(.25/.25/1+2) This tone was written for a Sipura SPA-3000 for a Panasonic KX-TD1232. The Panasonic does not support disconnect supervision, so this tone is the only thing that will detect a disconnect. It is not a standard fast busy or offhook tone.

I have a SPA-3000 that is failing to hanging up pretty often; almost every day now. The weird thing is that an almost identically configured (same FW, different HW rev) second unit right next to it isn't having the same problem. Swap the lines and the problem stays with the unit. I've been going round and round with Sipura and their latest message told me to use a procedure detailed in