Displaying 20 results from an estimated 100000 matches similar to: "SLA & Polycom"
2009 Jan 07
1
SLA and Polycom
Has anyone done SLA with Polycom phones? I've got a large project coming
up where the customer is keen on SLA for trunks and extensions. Trunks
will be on a PRI.
We may do this with Cisco phones if they work better.
Mark Willis
2010 Dec 04
3
Polycom Park by EFK
Has anyone gotten one-touch call parking to work on Polycom phones via
the Enhanced Feature Keys feature working? I've looked at various
examples, they appear correct, but the phones (501, 3.1.x firmware)
show the Park button while in a call but this does not actually cause
the call to be parked. Doing a SIP debug, I don't see that anything is
transmitted as a result of pressing the call
2011 Nov 30
0
SLA and polycom
Hello, every body
Anyone set up, the sla sharing line appearances, in asterisk, I'm setting,
tha but, don't, work, I change the sla.conf, extensions.conf, and sip.cfg,
but don't work fine.
Any one, could setup, tha?
Regards
Carlos Rojas
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2007 May 04
2
SLA broken in 1.4.3?
I configured my sla.conf to use with a Polycom phone. I have no idea
if I did it right, however, none of the console "sla" commands
exist. Do I have to something special to compile in this support, or
should it just work out of the box?
~jay
2007 Apr 25
3
SLA Appearance between 2 Cisco 7960's (SIP)
Has anyone had any success with getting SLA going between 2 SIP phones?
(Particularly a set of Cisco 79xx's) The SLA document that comes with
the asterisk source is about as clear as mud.
Does anyone have a working sip.conf, sla.conf, and extensions.conf that
I can use for reference?
The part I'm most confused about is how to build the lines in sip.conf
and how the phones should
2006 Oct 25
1
WiFi Phones (was Looking for Wireless Heaset for Polycom 501)
Martin:
I had seen your other post and sent you a message off-list, but I never got
a response. What do you feel is the most lacking that does not make it ready
for a production enviroment.
-
I've been using a SIP deskphone in my office and usually some sort of ATA at
my house, both as the primary phone. I've also had mobile phones from almost
every carrier. Each one of these devices
2005 Jul 18
2
Polycom 501 Configs
I just received my first polycom 501, tried my best to follow all of the
documentation and configs on the wiki ( though some conflicted in which
case i tried both ways ), and at the end of the day can not connect my
phone to asterisk.
My Questsions: does the wiki information apply to the 501's? The images
and config files at freedomphones, are those supposed to work with the
501? Has anyone
2005 Jan 04
6
Polycom Buddy Feature
Greetings,
Recently there has been talk of the presence/buddy feature with asterisk
and Polycom phones. I have it setup, and working as expected, however I
can only get 7 buddies to appear on the screen at any given time.
Has anyone gotten more than 7 buddies to appear? I'm just trying to find
out if this is some polycom limitation, bug, or my error.
Thanks,
Matt
--
Matt Gibson
VOIP
2008 May 09
2
Polycom Advanced Features
Anyone have shared lines (sla.conf) working with Polycom phones? Also,
has anyone figured out if its possible to do 1 button call park with
the softkeys?
2007 May 25
5
Polycom or Linksys phones bootp tftp config setup
Hi All,
Has anyone gotten the polycoms or the linksys phones to accept oprtion
66 on the dhcp request for the address of the tftp config server?
We have the dhcp server issuing the proper IP of the tftp server, but
the phones just sit there and never try to contact the tftp server for
their configs. We can see the proper option going from the dhcp to
the phones with ethereal trace.
Thanks
JR
2006 Feb 27
0
Polycom 501 issues
I am having a couple of (unrelated) problems with my polycom 501.
1. The buddy watch is just not working. It tells me that everyone is
online, whether or not they are.
Here is an example directory entry for one of the peers (whose phone is
not registered).
<item>
<ln>F</ln>
<fn>J</fn>
2007 Jan 25
2
1.4 - SLA
I have read that 1.4 has shared line appearances, which I assume will
work with Polycom phones. Has anyone configured this and verified it
working? I was going to start playing around with it but wanted to see
if anyone else has tackled it yet.
Bill
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
2006 Mar 07
1
OT: Polycom Registration Weirdness
This is a SER/Polycom question, but I hoped we may have some SER guru's here...
I have a series of Polycom phones that are tying to register with OpenSER. The phone sends a REGISTER message, and OpenSER replies with Unauthorised (all normal). The phone re-sends the REGISTER with the credentials, and OpenSER sends Ok.
Here's where it goes downhill. The polycom's appearance display
2007 Apr 11
2
FW: Polycom 501 issue with latest firmware : sluggish keys
Somebody was helpful enough to give me the very latest release of Polycom's
firmware (2.1.0). Unfortunately, I still get that issue.
So I'm stuck asking again: Anybody ever got that?
Mike
_____
From: Mike [mailto:list@virtutel.ca]
Sent: Wednesday, April 11, 2007 13:37
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: Polycom 501 issue with latest
2006 Jan 20
1
Need a good extensions.conf sm bus config w/polycom phones
Contact me off list, I have a sample extensions.conf file that I can
share. It has Paging (one to one and One to Many)
Ivr includes, time of da routing and it is geared towards Polycoms.
> -----Original Message-----
> From: asterisk-users-bounces@lists.digium.com
> [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of
> Thomas Johnson
> Sent: Friday, January 20, 2006
2007 Jan 03
5
Polycom Power Specs
Does anybody happen to know the input power specs for the Polycom IP 500
and IP 600? We've mixed up our power supplies and we've got a whole box
of them and can't figure out which go to the Polycoms. I would rather
not kill the phones by trying random ones....
2007 Aug 15
1
CallerID Error causes problems for Polycom phones
Hi everyone,
I have been dealing with a certain issue with a particular customer site
for months now. The problem occurs when there is an error with caller
id as shown in the following:
WARNING[16036]: chan_zap.c:6309 ss_thread: CallerID returned with error
on channel 'Zap/3-1'
When this happens, it appears that the call still goes through as I can
see the caller still navigating
2014 Mar 14
1
Working Config for Polycom VVX and Auto Answer
Hi -
Just wondering if anyone has gotten a Polycom VVX phone to
successfully do an Auto Answer with asterisk. I have an older
generation of Polycom phones that do this just fine, but I can't seem
to make the VVX phones work.
I tried the guide here:
http://community.polycom.com/t5/VoIP/FAQ-How-can-I-change-my-Ringtone-or-Ring-in-a-special-manner-for/td-p/5167
And I have this in my diaplan:
2015 May 20
0
SLA, SPA942, Asterisk 11.7.0
Fellow asterisk users,
I am trying to get Single Line Appearance functionality working on a set of
Linksys SPA942 phones and have not been successful. It looks like sla.conf
is not getting read, only one phone reads as registered for the shared
line, and a busy tone every time the shared extension is dialed. I have
followed the documentation [1] and followed through other threads I saw
2006 Jun 21
5
Polycom Intercom - almost there
Ok so I added to my Freepbx config running Asterisk 1.2.4 in
extensions_custom.conf
; intercom
exten => _7XXX,1,SIPAddHeader(Alert-Info: Auto Answer)
exten => _7XXX,2,Dial(SIP/${EXTEN:1},12,Tt)
and configured my Polycoms via this page
http://www.voip-info.org/wiki/view/Polycom+auto-answer+config for auto
answer and that works fine if I dial 7 then the 3 digit extension.
No