similar to: Strange State 6 on Channel X

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Hi everybody! I'm triying to install a Sangoma A200-R FXO card on a Debian Linux 5 (Lenny), 2.6.26 kernel. To install wanpipe driver I type: WANPIPE_FOLDER# ./Setup install Everything seems to be ok. There are no broken dependencies and the hardware is well detected, even zaptel is recompiled with no errors, but at the time to compile wanpipe I'm getting this error message:

I am building a new Asterisk server here at the office, and I'm wondering if there are any downsides to creating my dialplan with AEL. It seems more intuitive (to me), but I'm not sure if there are any pitfalls I need to be aware of first. We use this for internal extensions, 8 pots lines, and our answering service which gets about 500 incoming calls a day down our T1. Also, one more

Hi! Guess I am doing something totally wrong here: Some smart person could maybe plz tell me what.

I'm currently using the Linksys PAP2, and since there's a shortage I'm looking for different devices. I'm mainly looking at the Sipura SPA sets since they are the base of the pap2. Anyone else have experience using them, and which one? Thanks Sherwood McGowan -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

I recently configured a SIP peer which i must specify my fromuser as my ten digit "DID". I send calls to this peer, but whenever Asterisk sends an options message, the fromuser is "asterisk". Is this a bug? Or is there some other config I must make ? register = 2155551941:123456 at 10.0.138.226/2155551941~600 [peer](!) type=peer context=inbound qualify=yes

Has anyone else had problems with users being able to press key tones during a voice prompt? I have a few users complaining that some systems will not recognize key presses during them. using current CVS-HEAD, linksys PAP2 UA's, rfc2833 dtmf mode. Thanks Sherwood McGowan -------------- next part -------------- An HTML attachment was scrubbed... URL:

On 04/05/2011 03:06 PM, asterisk-users-request at lists.digium.com wrote: > Message: 12 > Date: Tue, 5 Apr 2011 13:36:21 -0500 > From: Sherwood McGowan<sherwood.mcgowan at gmail.com> > Subject: Re: [asterisk-users] Iptables configuration to handle brute, > force registrations? > To: Asterisk Users Mailing List - Non-Commercial Discussion > <asterisk-users at

I need help translating extensions.conf to AEL: [default] exten => _X.,1,Set(DID=${EXTEN:6}) exten => _X.,n,Goto(continue,1) exten => _1X.,1,Set(DID=${EXTEN:7}) exten => _1X.,n,Goto(continue,1) exten => continue,1,Noop(${DID}) exten => continue,n,Set(GROUP(IAX)=incoming) exten => continue,n,GotoIf($[${MATH(${GROUP_COUNT(incoming at IAX)}+${GROUP_COUNT(outgoing at

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

I'll keep this brief because I don't want to come across like any more of an a$$ than I absolutely have to, especially since I know I've blown my stack before..... Gentlemen (and Ladies, if you're out there), If someone gives you advice on this list, and ESPECIALLY if they give you advice offlist, have the courtesy to (AT THE LEAST) to let them know when/if you get your question

Guys, I've been poking around trying to find a good answer for this via voip-info, google, etc... Haven't found anything that helps, so maybe you mates could. A lot of my customers are using Linksys UAs (router/ATA PAP2) and some using Sipura SPA-2002s. Every once in a while, the customer will get one-way audio. I've read that this is commonly caused by the outgoing RTP port not

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I had the opportunity to test a Sangoma A200 card and I have some doubts that I would like to consult: I tried to detect the card and I had no success using the wctdm module with DAHDI. I guess this is because electronics is different because the TDM400P and OpenVox A400P cards have separate modules for each channel, while the Sangoma A200

Hi, I'm trying to install asterisk(v1.2.22) with FreepBX(v2.2.3) with a 4-Port FXO Sangoma card A200. I'm using Fedora 7 (x86_64) kernel version 2.6.22.1-27.fc7, but i'm having these errors: $ ztcfg -vvvv Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS

Alrighty Gents, let's see if any of you have encountered this one...Variables losing their value...I'm setting a variable with four underscores (used to be two, had same issue) so it can be inherited by child channels, and then the next line in the dialplan I use it but it appears to be empty...I've googled and found nothing stating this kind of weirdness.. Asterisk 1.8.2.2 (upgrading

Anyone have a good tool(s) to use for simulating a bunch of calls? Benchmarking or stress testing? I only need SIP protocol, and do appreciate any replies...I realize I could google it, but I am looking for opinions as well. Sherwood McGowan -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hey all, I'm trying to create redial on busy for my users, but haven't the foggiest on how to make asterisk route depending on the status code returned over SIP (483, Busy Here?). . . anyone know how to do this? Thanks Sherwood McGowan -------------- next part -------------- An HTML attachment was scrubbed... URL: