similar to: BRI hardware supported by 1.6 libpri ?

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that

Hi list! I'm totally fed up with bristuff (or it's instability with a simple HFC-S card), 2 out of 3 times when people try to call they get the information tone that the number is not connected. I would like to try vzaphfc and I am looking for information on it. >From previous posts I found that the only place where the sources seem to be maintained and available is at the debian

hello, Here (http://updates.xorcom.com/astribank/bristuff/1.4/INSTALL.html) you can read : cd qozap modprobe zaptel insmod qozap.o (for kernel 2.4) insmod qozap.ko (for kernel 2.6) ztcfg I thought modprobe was a replacement for insmod. Can someone be kind enough to explain : 1. the difference between modprobe and insmod, 2. why should both commands be issued, 3. how modprobe and insmod compare

Hi, At the moment, libpri /w Asterisk 1.6, Dahdi 2.1, is not supporting NT-Point to multi-point mode. Here (France), most small PBXes are connected to ISDN through BRI trunks in PtmP (don't know why but it seems the general case). So this NT-PtmP function would be very helpful to easily slide an Asterisk box between an existing PBX and the network. Does the same case apply elsewhere (UK,

Hi list, Is Digium Wildcard B410P compatible with Asterisk 1.2 / 1.4 (zaptel of course) directly out of the box, or do I need things like bristuff? http://www.digium.com/en/products/hardware/b410p.php Best regards, Henrik Woffinden

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

Hi, I just got a Xorcom Astribank with 8 FXS but it does not work. So I tried resetting and loading the firmware. But loading just times out. /usr/share/zaptel/xpp_fxloader usb --------- FIRMWARE LOADING: (usb) [1 devices] 'xpp_fxloader'[11561]: USB Firmware /usr/share/zaptel/USB_FW.hex into /dev/bus/usb/002/003

Hi, I've read that the new dahdi channel supporting B410P doesn't support PtmP when in NT mode. Does it support PtmP when in TE mode ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20081209/f422b5d0/attachment.htm

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hi list! I have to do a new bare metal installation of a box running Asterisk with bristuff or vzaphfc. The box will be used as a really lightly loaded file server and pbx. Any advise on which architecture I should use? The cpu is a 64 bit capable AMD (the box is running x86_64 now) but is still suffering from echo on the BRI lines. Should I go with the normal x86 or the 64 bit x86_64

Hi all. I'm looking to set up a fax via email service so that users can email a specific mailbox and receive fax's to a specific mailbox. Can this be done? I've had a look an SpanDSP and I think that's what I want but I'm not sure. Cheers Matt

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

Hello, I'm evaluating to possibility to use chan_misdn as a short term workaround, in case latest Dahdi is not stable enough for what we are planning to do (we wish to use Junghanns and Digium BRI hardware with Asterisk 1.6) . I've read www.mISDN.org but still have a couple of questions : 1. Is correct that in a 2.6.27 (and up) enabled kernel, the "embedded" mISDN version is

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

I'm not aware of any zaptel driver for such HFC USB modem (some Xorcom's products use USB, so ...) so I'm inclined to think it's not possible but it's better to ask ... Cheers ------=_Part_13548_28463665.1207585749504 Content-Type: text/html; charset=ISO-8859-1 Content-Transfer-Encoding: quoted-printable Content-Disposition: inline Hi

Hello, I am trying to install the drivers for the Junghanns quadBRI card, but am having a problem. I have essentially followed the procedure from http://www.voip-manager.net/installation-linux-asterisk.php. At the stage to install the ISDN card I have completed the following: 1) downloaded the bristuff-0.2.0-RC8q.tar.gz to /usr/src 2) unpacked it in /usr/src - tar xvzf bristuff-0.2.0-RC8q.tar.gz