similar to: question on meetme

Hi, I don't have a zaptel device for conferencing. I read from the lists, that ztdummy and zaprtc need to be installed to get conferencing. I could able to compile successfully with ztdummy and when i receive the call it says, -- Goto (13732,s,1) -- Executing MeetMe("SIP/-08118800", "1234") in new stack == Parsing

Kristian, I have 2 X100P cards but neither work on my Compaq DL360 G2. The system will not even boot! Take a look at my initial post and let me know if you have any other advice. Regardless, thanks for your post! ------------------------------------------------------------------------ - I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards

Does anyone know where to disable rtc support on redhat 9.0 using make menuconfig? I thought I disabled it but still got the following error when trying to make zaprtc: zaprtc.c:109: storage size of `rtc_irq_timer' isn't known zaprtc.c:719: storage size of `rtc_fops' isn't known zaprtc.c:107: warning: `DECLARE_WAIT_QUEUE_HEAD' declared `static' but never defined make: ***

I ran in to an almost impossible ability to run MeetMe on our poweredge. Our PE is a 4 proc with OHCI and we had no need to buy any PCI cards other than for running MeetMe. If you know how to recompile your kernel, recompile it and make RTC a module (its compiled in by default). Then you can use zaprtc as your timing source. Be sure to `rmmod rtc` before you `insmod zaprtc` because zaprtc is a

Hi, I know this question may have been asked before (although the archives don't seem to suggest it), but has anyone had any problems with Asterisk accepting a PIN number for a conference room. At this point in time I have established the conference definition in the meetme.conf file as well as specifying the appropriate lines in the extensions.conf file. meetme.conf file: conf =>

Any help would be appreciated as I am a novice trying to work around a difficult situation. This is what the zaprtc helpfile says: zaprtc, getting zaptel timing out of your realtime clock ======================================================== Make sure that you _dont_ have rtc support compiled into your kernel! INSTALL: make USE: make load REMOVE: make unload I interpreted this as

Hi all, I'm configuring meetme in asterisk but no luck. I dont have a digium card, so based on the wiki, i have to install the zaptel driver and enable the ztdummy on it. I compiled, install the module and enable it on the module.conf. When i tried to start the asterisk, asterisk wont start because of the error in loading the meetme module. Jun 16 15:36:56 WARNING[-1084989312]:

I need a timing device for the DL360G2 for conferencing and meetme. For a timing device I have 2 X100P cards but neither will work in my DL360G2. The system will not even boot with either card in the system. Other PCI cards seems to work fine. I called Digium support and was told that there must be a conflict between the card and my Compaq DL360G2. I then moved on to ztdummy. I'm sure the

Hi All, I observed the following in my try towards Multiparty Conferencing. I am establishing the Multiparty Conferencing through Asterisk Manager API. I have two users SIP/111 and SIP/101 of which SIP/101 is treated as leader. Following commands are used - Action: Originate Channel: SIP/111 Application: MeetMe Data: |edwx ActionID: ffe4563 When I use the above, Incoming call will

Hello all, I really appreciate the replies I've gotten about this so far (especially the support for wanting to run it on Solaris!). The core issue seems to have been missed, though -- is there any way to run a complete Asterisk solution on Solaris 10 (including music-on-hold and conferencing)? This probably comes down to a few issues: - Is ztdummy (a component of Zaptel) *really*

I'm running into a bit of a problem setting up conference calls. The box I rent at a colo doesn't seem to have USB hardware.... When I try to load usb-uhci I receive a "device does not exist" error. Which means I can't load ztdummy.... The system has a rtc clock module, so zaprtc won't work... (which I'm scared to unload rtc because I don't have physical access

This is not directly * related, but could be. My company is using a VoIP conferencing solution that is suffering from developer neglect. I've considered trying to leverage *, and our internal developers can build the management interfaces. If that plan is not accepted by management, I need to find a commercial solution that works. Requirements: H.323 SIP G7.11/G7.29 Multiple unique

I try to use meetme app after reading manual i compile and install zaptel with ztdummy when i make lsmod i have ztdummy 2532 0 (unused) wcusb 20064 0 (unused) zaptel 179168 4 [ztdummy wcusb] usb-uhci 26348 0 [ztdummy] usbcore 51616 0 [wcusb usb-uhci] after it i recompile asterisk and after it i have

Any thoughts on the following? I am running asterisk from CVS (downloaded yesterday's version, just to be sure) on a test system with no digium cards in it, so I have installed ztdummy (see logs and screenshots below) as a timing source. When I call the music on hold extension from a Sipura Sip connected analog phone, I hear nothing and start getting Warning[98310]: chan_sip.c:674

I do not have any zaptel hardware on the Asterisk box, I could not have meetme functioning. I did modify the Makefile in zaptel directory on line 168 by including ztdummy as one of the modules to compile in. The error message from the concole: -- Executing MeetMe("SIP/1002-e9ca", "4700") in new stack == Parsing '/etc/asterisk/meetme.conf': Found

Hellos, I am having issues with my meetme conferencing. When I dial the conferencing number, It hangs after a few seconds.I have read somewhere that I need to enable ztdummy, which I have done but still no changes. Here is my log ~=~=~=~=~=~=~=~=~=~= PuTTY log 2009.08.12 18:44:43 =~=~=~=~=~=~=~=~=~=~=~= -- Executing [1;36;40mMacro[0;37;40m("[1;35;40mSIP/1215-fc5b[0;37;40m",

Yes, I am a newbie too. I am having a problem with meetme. From what I have seen it will work without a Digium card but with audio problems. My goal is just to see how it works not the quality of the audio. When I dial into the conference room the following message is played: "That is not a valid conference number." On the console I get: "unable to open pseudo channel". As

Hi all, I'm trying to get the MeetMe system to take a caller and announce to them they've joined the conference in addition to the other members of the conference assuming previous members of the conference >= 1. I can see where the meetme.c app actually processes it using the ast_pthread_create_background(&conf->announcethread, NULL, announce_thread, conf); function. The

I have a system with no Digium hardware in it (two others with 2 X100P cards in each of them as well). I'm interested in using MeetMe in the one without the hardware (it works great in the ones with the hardware). I can't use ztdummy, because the system has usb-ohci drivers, rather than usb-uhci. I have read the little there is about zaprtc, and I am wondering whether there is a

I am running asterisk 1.4.18 trying to use MeetMe and option b. I am getting permissions denied failed to execute conf-background.agi on the CLI lrwxrwxrwx 1 root root 37 Mar 17 10:11 conf-background.agi -> /home/silentm/bin/conf-background.agi my conf background is a symbolic link - then my permissions are : [root at devcentos5x64 src]# ls -l /home/silentm/bin/conf-background.agi