similar to: Asterisk: how to limit h323 connections.

Hi to all, I've installed Asterisk 1.4.9 with h323, and gnugk as soft gatekeeper. I've tested h323 using ohphone and I can talk between them, then I've tested SIP with Twinkle softphones and function very well. Now I have to perform call from h323 to sip and viceversa. How can I do it ???? I receive h323 call from a Cisco Voice GW to my Asterisk and this call have to go to a SIP phone:

Hello everybody, my * box is connected to gnugk with H323 channel. If I call from an H323 EP to SIP EP (GS HandyTone or Xlite), when callee is picking up, audio start but noisy (scratch) , then became ok for callee (SIP EP) but still scratching on H323 EP. Now I stop/start asterisk, call from SIP to H323 EP and it's ok. And from now, it's also ok when H323 EP call SIP one's! No

During debugging of H323 trunk side (using Jeremy Macnamara's H323 driver in ~/channels/h323) a couple of things come don't quite work as advertised... 1/ the following line in extensions.conf explicitly sets the outgoing caller ID (required in my case for downstream GK processing..) exten => _1NX.,1,SetCallerID,6400047602100 exten => _1NX.,2,Dial,H323/${EXTEN:1} what

Hi, I am using the asterisk-oh323 wrapper and I am looking to allow registration of h323 endpoints and allow Asterisk to act as a gateway. The idea is simple: H323 endpoints would register with Asterisk. They each would have their own internal extension (like SIP). If a H323 endpoint dials an outbound extension, then the h323 call gets routed to a H323 Gatekeeper which then terminates

Hi All, I have set up a box that will be used as follows: SIP Phone ----> Asterisk ----> Cisco H323 VoIP Server 192.168.1.5 192.168.1.50 192.168.1.80 Asterisk is running the latest CVS and oh323 driver. The SIP phone is a Grandstream Budgetone 100. I have everything setup and running with G.711 ALAW and ULAW and i'm able to make calls through

Use oh323. Download the openh323 and pwlib tarballs from openh323.org Follow Jeremy's instructions in the /asterisk/channels/h323/ directory EXACTLY! good luck Regards, Sean Langley, P.Eng Firmware Engineer General Dynamics Canada (403)730-1482 sean.langley@gdcanada.com > -----Original Message----- > From: Senad Jordanovic [mailto:senad@cwcom.net] > Sent: Friday, September 12,

Hello! I see many of you experience troubles with H323 stack. I am focusing on building H323-SIP Asterisk based softswitch with all codecs supported (including G729 and G723). I can setup Asterisk from scratch with H323 support or solve your h323 nightmare with existing asterisk system for for 100$. Contact me pls offline.

Hello. I have a codec problem to send calls from a SIP device to a H323 gateway. First I'll explain the scenario: - Asterisk 1.2.1 - The SIP phone can use any codec I want. - The H323 gateway can only use g729 (cause it's not under my administration) - SIP phone has g729 configured, so my asterisk doesn't need to "transcode" (I don't have licences for g729) - sip.conf

Hi all. I can''t seem to get the h323 connection tracking configured correctly for Shorewall. I am using the Debian Shorewall 4.5.16.1 package. I am running a Debian 3.9 kernel like so: # uname -a Linux gw 3.9-1-amd64 #1 SMP Debian 3.9.8-1 x86_64 GNU/Linux My version of iptables is: # iptables -V iptables v1.4.20 If I add the following rule in the /etc/shorewall/tcrules file to

Hello everybody, First time installer and I need the lists advice. My plan is to use asterisk PBX with some hardware to terminate my calls coming from several operational gnugk gatekeepers. Do have RH9 and downloaded the latest asterisk from CVS. Compiled according instructions and is running fine. Could hardly find any info on h323 implementation untill the REAME in the channels directory.

Hi, is it possible to use Asteriks for translating SIP to H323 and vice versa? I am looking to implement the following Setup SIP UAC <-> SIP-Server <-> SIP/H323 Proxy <-> H323 Server <-> H323 UAC Basicly i want SIP fones to talk to H323 fones and and SIP Fones to access PSTN Gateway(s) in a H323 network. Anyone got something similiar running? Any ideas? best regards,

Hello, I trying to set up an h323 channel over TCP/IP network to connect two PBX. I just read http://www.voip-info.org/wiki-Asterisk+config+h323.conf but, it don't solve my dubs. How could I use a h323 channel with asterisk? Could anyone paste a part of h323.conf file? I am no sure how to setting up h323.conf. And the part of extensions.conf where you use the h323 channels for an specific

We come into this section of the dialplan: exten => 88670333333,1,Wait(1) exten => 88670333333,n,SayUnixTime exten => 88670333333,n,NoOp(If you know the extension ...) exten => 88670333333,n,Dial(${PHONE_6003}) The caller from the GK hears only ringing, not the time. The extension 6003 rings and I can pick up, but without any voice nor video. athome*CLI> -- Executing

Does asterisk support using an H.323 provider for outgoing calls? From everything I have found, it looks like it does. However, I have had no success in getting it to work. I would really appreciate if somebody could give me a hand. I am using the channel that comes with asterisk. I have also tried using the channel from inaccessnetoworks but have not had any more success. My provider

Hi, I start to be a little confused so I am asking to the list. I want to make with * a gateway from PSTN to H323, and to send all incomings call to a predefined IP, which will treat the h323 calls. let's assume that all my incoming numbers starts with 00 here is my extensions [incoming] exten => s,1,Answer exten => _00.,1,Answer exten =>

I have build asterisk from latest CVS HEAD-05/09/05 with H323 support as described in README file. Open H.323 version v1.17.1 and PWLib v1.9.0 on Mandrake Linux 10.2 kernel-2.6.11 I tested it with following phones: -- XLite (SIP softphone) -- QMix SIP IP phone (PA168F) -- SJPhone (H323 softphone) -- QMix H323 IP phone (PA168F) -- FireFly (IAX2 softphone) Everything works fine except a problem

Hi all, I have this installation: Asterisk 1.6.1.1 with h323 support, pwlib_v1_10_3 and openh323_v1_18_0. I have a problem that is, when a call comes from H323 and goes to a Sip phone the asterisk sends two rtp streams to the sip. I checked this with tcpdump, save the payload (voice is in G711u), one is the ringing indication and the other is the voice coming from the user in h323 side. And

Hello all, I am trying to use native h323 built from asterisk 1.2.7. I configured the h323 to receive incoming calls...the problem is i can receive the call to my asterisk and it rings another extension but no audio. I don't see any good documentation about gatekeepers, fast start, etc with h323. I would like to get some help from you guys to fix this issue. If any of you have configured

Ok, at the bottom of my h323.conf file on my 1st server I have this: ; --------------------- [test] type=user host=209.237.227.185 context=termination-test incominglimit=10 accountcode=005 ; --------------------- Using an Asterisk at the other IP, I have this: exten => _1NXXNXXXXXX,1,Dial(H323/${EXTEN}@64.135.11.85,,o) This should send a call from the test-server to the IP of the 1st server;

Hi, I installed H323, however when I make a call from SIP Phone -> Asterisk H323 -> Provider H323 the provider can hear me, but I cannot hear nothing. The asterisk is 1.2.6 with G729 license, and the asterisk is connect direct to internet with a public IP. Any thoughts? -------------- next part -------------- An HTML attachment was scrubbed... URL: