similar to: Using Asterisk to connect 2 locations with legacy PBX

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

hello, everyone there is anybody can help me, what is the address of the samba lastest release samba 3.0 samba 2.2.x because i wanna upgrade my current samba server 2.2.3a

Hello. I am administrating about 30PCs with W2K and users are authenticated in SAMBA running as PDC on Linux. About 16PCs have the possibillity to boot also into Linux. I would like to authenticate also linux users using the samba, because I do not want to copy passwd, group, shadow each time I add a user, or even add the user on each PC. I do not use LDAP a do not know NIS. Is it possible to use

> > Great service. Hope it catches on. > > > > In time there will probably have to be some adjustments: > > > > - ratio 10/1 - this means everyone can make 10 calls for every call > donated. > > This doesn't add up in the long run. > > - I get credited 10 calls for every call I make to my own dialplan. This > > should be fixed. > > -

hi all, we do have some troubles with zaptel timing source - we have a setup with 3 telco PRI lines, connected to asterisk digium card 0 - asterisk does some handling - calls are leaving on digium card 1 - going to a siemens hipath - there is some call handling - some of the calls then are going from the hipath over a qsig line to a bosch integral PBX - handling the rest of the calls. To be able

Hi all, i have asterisk 1.2.17 with sip tcp support and i am trying to connect asterisk with HiPath 4000 V.3.0 using SIP. I can see the registration from the HG3540. But when i try to place a call from Asterisk to HiPath, the call fails with SIP/2.0 603 Declined. The strange thing is that the first INVITE uses tcp and the response is a 100 TRYING, the next 7 INVITE are using udp and the respose

Hi Stephen, You said that PRI works great. We are using HiPath 3550 and Siemens digital phone which using *11, *97 etc for function keys. However Asterisk uses the the * key plus one or two digits for function keys as well(it is common key combination for functions). So is it any way to disable *11, *97 keys in HiPath system and pass this keys to Asterisk? Thanks and regards, Isaac >Hi

Hello! Is it possible to connect Siemens HiPath 4000 to Asterisk? What equipment required on Siemens side? I mean IP not E1. Sorry for asking here. Siemens-related websites use "salesperson language". There is no technical information.

Hi all, I'm trying to setup Asterisk trunk to Siemens HiPath 4000 V2.01 What would be the best way to do so? I am a bit confused because as far as I've understand this PBX doesn't support H323, but I saw somewhere someone who created a cornet trunk and it worked using H323. So if anyone knows what I need to configure I would appreciate it. I've read some information

I am connecting to a siemens hipath 4000 with dahdi 2.1.0.4 and asterisk 1.4.23 using a Te210P card. the phone guy is saying that the lines are reporting always BUSY. however on my end the status shows OK. Anyone seen this? Is there something different about connecting PRI to siemens hipath? system.conf shows: loadzone=us defaultzone=us span=1,1,6,esf,b8zs bchan=1-5 dchan=24

I downloaded asterisk to use cvs to checkout the release version. After installing, I would like to load module chan_h323.so but there is some error : *CLI> load chan_h323.so Feb 17 15:22:38 WARNING[2865]: loader.c:258 ast_load_resource: /usr/lib/asterisk/m odules/chan_h323.so: undefined symbol: __use_ast_pthread_create_instead__ Unable to load module chan_h323.so *CLI> How can I solve

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

For all who are interested: A quick review of CeBIT 2005. :-) CeBIT was a very successfull event. Most of the time, the asterisk-booth was crowded with more people than we could talk to. We had with us a demo-installation including different IP-phones, digital and analog phones as well as a Siemens HiPATH PBX to which our Asterisk-server served as a VoIP-gateway, and many people were impressed

Hi Group, I am currently facing a dead end and any help will be much appreciated. I have an a104d installed in an asterisk box, two of which is configured on ISDN pri. One is facing pstn and the other one is facing a hipath 300e Siemens. I am getting one way audio when a local on the hipath tries to make a pstn call but no issue on incoming calls from pstn going to the hipath locals. local

Hi * :-) I found in the online WiKi docs some information on how to integrate Asterisk with "old PBX"... http://www.voip-info.org/wiki-Asterisk+legacy+integration ...but I couldn't find anything on integration with a Siemens HiCom 150E. Later on we'll migrate to a HiPath 3750 so information covering this model would be nice too... Do you know if any of the PBX listed

Hello all, I am trying to connect asterisk to a Siemens Hipath 3750 PBX system. I have a physical connection issue. I know that I should use a crossover RJ48 cable to link the two systems. The problem however is that the physical interface of the Siemens system is very unfamiliar. From my digging around, I think that this is an S2M interface. http://www.mail-archive.com/asterisk-users at

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

Hello all. I have installed and functioning asterisk-1.2.9.1 where I effected one upgrade in asterisk-1.0.9, is interconnected with a PABX Siemens HiPath 4000 in ISDN PRI with protocol QSIG, the one that is happening he is that the calls originated for PABX Siemens and destined to SIP phones asterisk are being without audio, nor Ring, is dumb. They could help in this case me? Best Regards Josu?

Hi, I am currently using asterisk to record all incoming calls. My setup is as follows, the asterisk server has a two TE120P cards one of which sends/receives calls from the carrier and the other is connected to a Siemens HiPath 3000. All calls that come into asterisk use MixMonitor to record calls and this works fine, but if a call gets transferred the transfer information is not sent back to my

My wife has just gotten a new printer which works perfectly when connected either to her Win98 box or to my woody box. However I am unable to share the printer between the two machines. Here are my choices in order of increasing desireability. I could of course just move the cable whenever I want to print from my box. This is the obviously least desireable option. The windows machine can