similar to: PRI span configuration - span remains down

Hi I posted earlier about having issues connecting to Telewest's ISDN, only to find out later Telewest had forgotten to turn it on - hopefully I'm not having a similar silly problem. My PRI span is now up and operational, but when I try to send a call out over it, I just get congestion tones. Occasionally, I get about one second of ring tones, only for it to cut out and play congestion.

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

what happens when you drop your gains? use /etc/asterisk/zaptel.conf and fiddle with tx and rx values. Works, most of the time. -----Original Message----- From: John McEntee [mailto:john@mcentee87.freeserve.co.uk] Sent: Wednesday, October 11, 2006 12:25 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [asterisk-users] Echo problems on ISDN. (mainly incoming calls) OK I

OK I have been battling with echo problems with asterisk on ISDN for a few weeks now, and still can't solve it (although I think I have tried everything I can find.) I will try a post everything I think is possibly relevant that I can remember with the hope someone can point me in the right direction. current spec I am using (Trixbox 1.0 was still in beta at the time an didn't detect

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Would be nice to do both (type 2 and 3 I believe in Oftel terms), but I'd accept just our DDI if that was all I could get. Steve -----Original Message----- From: Storer, Darren [mailto:starusers@comgate.tv] Sent: 01 July 2004 09:35 To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Providing Telewest in the UK with per extension outbound callerID Hi Steve,

Hi, Is anybody in the UK using Telewest as a PRI Telco provider? Are you sending them caller ID? I've been told by Telewest that:- 1. Oftel doesn't allow them to accept caller ID (this is rubbish, and I replied pointing out where in the link to Oftel that they sent me it was stated. We need Type 2 caller ID) 2. Telewest can't do this. (this is rubbish, I'm certain

Hi Folks, I have a T100P ordered from Digium in the past. Its working perfectly fine but I now need to more the server to India (out-sourcing) and we will be getting an E1 line there. Does anyone know if T100P was capable (upgradeable) or swappable so that I could use it with the E1 lines instead? Any pointers to driver/firmware update would be highly appreciated. Thanks. R -------------- next

A client used to use BT isdn30 and ported the numbers to telewest several years ago. Now, the client moved to adept telecom. I *think* adept resells BT products. We got new numbers from adept (bt?) and the old pbx on the telewest lines forwards the calls to the new numbers. On the adept line I got a digium card in an opteron supermicro server. ztcfg gives me over 99.99 pretty much all the time.

Hi list, I have a terrible noise issue with Dell SC1430 + Digium TE110P. The digium card is not sharing interrupts with any other device, as I saw in Dell's BIOS and also with "lspci -vb" command. After changing coax wire, UTP, balum, digium card ... I have found that the problem is in Dell box, so now I'm running the same Asterisk config in other server with the same

Folks, I've seen a few reports that people have had problems with hang up detection on UK cable phone lines. I have a TDM400P with two FXO ports, one connected to my BT line and the other connected to my Telewest/Virgin Media cable line. If I ring the BT line and then clear down, Asterisk detects this and acts accordingly. If I ring the Telewest line, the clear down is not detected, hence

Hi, ? I'm trying to figure out what the issue is splicing Asterisk between our Telewest PRI and a GDK-186 with a PRI card. ? We're using the Digium TE405P ? Our telco provider is Telewest, and Telco directly into switch is fine. ? When I splice Asterisk in, I can make and receive calls from Asterisk extensions, I can make outbound calls from the GDK, but inbound calls do not seem to pass

Guys. I have an issue with a te110p card and also some tdm04b cards on the same system: Zttest returns this for the tdm04b cards: [root@mollendo ~]# /usr/src/zaptel-1.2.4/zttest 38 -v Opened pseudo zap interface, measuring accuracy... 8192 samples in 8191 sample intervals 99.987793% 8192 samples in 8192 sample intervals 100.000000% 8192 samples in 8192 sample intervals 100.000000% 8192 samples

Hello, Could anyone please give some information on configuring asterisk as a gateway. What contents have to add in h.323 .conf and extensions.conf files ? Thanks & Regards Bincy K Philip -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20071102/53be51ce/attachment.htm

I am on UK Cable (Telewest) will this callerid patch work with the cable caller id? Thanks. Paul.

I think I am the first to use the $135 Avaya 4602 SIP phone, but I need some support from the community to fix one problem I have with it. The phone stops working after about 20-30mins if I have mailbox=context in Asterisk; when I do have mailbox=contect in asterisk the sip debug returns "481 extension does not exist." Anyone willing to help me figure out why? I.E. Is it an Asterisk

Skipped content of type multipart/alternative

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hi I can't for the life of me work out why this is not working. When in the campon contect if you hit a DTMF key 2 you get moved to the exten => 2 defined in the mainmenu context not the exten => 2 defined in the campon context. What is wrong? The same happens if you hit key 1. [campon] exten => _*1XXX,1,Answer exten => _*1XXX,2,SetCallerID(${CALLERIDNUM}) exten =>