similar to: Issues with making calls

I had MCGP working to a ADIT 600 fine with debain sarge stable / asterisk stable - wanted to try red hat and got the below message - then I re-installed debian and am still getting the same message below - any comments are greatly appreciated - I did play with the config files with no prevail - the Adit seems to be doing its job per tech support at CAC. I listed my conigs below I go off hook

Asterisk Users, I have 3 FXO modules with the TDM400P Digium Card. I can dial into the Asterisk rings my Sip phone, but dialing out with my SPA941 phone through the zap channel is a problem. I keep getting this message on the Asterisk CLI. What am I doing wrong? Thanks in advance. -- Executing [103 at default:1] Dial("SIP/200-006fa300", "{Zap/g0/{EXTEN:1}") in new

Hi My asterisk output is: chan_sip.so => (Session Initiation Protocol (SIP)) Asterisk Ready. -- Registered SIP '201' at 192.168.0.55 port 33906 -- Saved useragent "X-Lite release 1011s stamp 41150" for peer 201 -- Executing [907768385144 at default:1] Dial("SIP/201-083e75c0", "ZAP/g1/907768385144|60") in new stack [Oct 4 11:54:27]

Hi, I asked a time ago what were callgroup and pickup group used for. I have done some proofs and all, and I'm not sure if I have pick the idea up well!! That's what I understand: For example: group=1 callgroup =2 and pickupgroup=2 and my phone is a membership of the group 1. that's mean that when a phone that belong to group 2 is ringing, I'll be able to answer this call dialing

Here is the diff from chan_sip.c 15 days ago and 16 days ago. 15 days ago is the point outgoing calls made via grandstream budgetone stopped working. Any help on why it breaks? Any possible fix? /tmp# diff asterisk/channels/chan_sip.c asterisk.works/channels/chan_sip.c 289d288 < int capability; 3921,3922d3919 < p->capability = user->capability;

Hi all, at time i am trying to get a better idea of callgroups and pickupgroups (especially within the SIP Channel) A Pickupgroup is relative clear - everyone in the same pickupgroup may pickup a call And a callgroup does what ? - The same ? I thought that a callgroup would act like the ZAP groups - so that you then can dial SIP/g1 - and every SIP Client which is in the callgroup 1 does then

Sir, i am using goautodial server , bri card is showing ok but when i try to call that showing below , This configuration is in doing in dubai , so kindly help me how can connet the call from this , what is my mistake is in this :::chan-dahdi.conf [channels] #include dahdi-channels.conf language=en context=default usecallerid=yes hidecallerid=yes callwaiting=yes usecallingpres=yes

The problem: T100P connected to an Adit600. Channel 1-16 are FXS, 17-24 FXO. I have Zap/24 in callgroup 3 and Zap/1-16 in pickupgroup 3. When a call comes in on Zap/24 I cannot pick it up with *8 from Zap/1-16. *CLI> show version Asterisk CVS-04/27/04-23:48:08 built by root@tuck on a i686 running Linux The zapata.conf and extensions.conf are located here:

I have just started to play with callgroups and pickupgroups.. I updates my * from CVS this morning (about 15 mins ago).. I have placed callgroup=1 and pickupgroup=1 into each of my 3 phone configurations in sip.conf.. I place a call from phoneA to phoneB, then I go to phoneC and dial *8# , the call does not get picked up by phoneC and continues to ring on phoneB.. Have I not configured

I'm trying to set up asterisk so any phone connected to channel 1-16 of my Adit600 channel bank can pick up a call coming in on channel 24. I do not wish to ring any of the 16 channels on an incoming call -- this is strictly so I can pick up the line if I see it ringing and wish to answer at work. I have channel 24 in call group 3, and channels 1-16 in pickup groups 1 and 3. However

How I change my configuration to reduce this issue. I have this setting on my zapata.conf signalling=fxs_ks group=1 callgroup=1 pickupgroup=1 channel=1 signalling=fxs_ks group=2 callgroup=1 pickupgroup=1 channel=2; singalling=fxs_ks group=3 callgroup=1 pickupgroup=1 channel=3; singalling=fxs_ks group=4 callgroup=1 pickupgroup=1 channel=4 and for outbound calls I have this context on my

Hello Group, Current Setup: - Eicon Quad BRI ISDN Card. - 4 ISDN BRI (Telco: Telstra) Onramp2 services. - Mode: Point2Point. - 100 Indial Number ranges. Full National Number (9 digit format): BAAAAAAXX where: B (Area code): 2/3/7/8 A (Normal Numbers) X (99 Indial extensions) eg: BAAAAAA00 BAAAAAA20 etc Requirement: - To be able send Indial numbers as Caller ID when dialing out. Configration:

Daniel Heckl <daniel.heckl at gmail.com> schrieb: > You are searching for ?Call Pickup?. It is implemented in Asterisk by > default. > > https://wiki.asterisk.org/wiki/display/AST/Call+Pickup > <https://wiki.asterisk.org/wiki/display/AST/Call+Pickup> Take a look under > section ?Configuration Options?. Hi, Daniel! Thanks for your answer... I'm using Asterisk

Before you jump ahead, yes I do have chan_zap.so loaded.. Call Flow: Asterisk 1 --IAX2--> Asterisk 2 ---> PRI -- Accepting AUTHENTICATED call from 22.22.22.22: > requested format = ulaw, > requested prefs = (), > actual format = ulaw, > host prefs = (ulaw|alaw|gsm), > priority = mine -- Executing

Hello, We are using asterisk 0.4.0 on debian sid with Cisco 7960 and ATA186 phones. All sip entries have: callgroup=1 pickupgroup=1 However I am unable to remotely pickup a ringing phone using *8#. I get fast busy tone. Is there some flag to add in extensions.conf ? Thanks in advance,

Hello I have a Junghanns ISDN BRI card for incoming calls and use SIP Polycom IP300 phones. My config files look like this: features.conf pickupextn = *8 zapata.conf context=frompstnisdn group=1 callgroup=1 pickupgroup=1 I also edited sip.conf like this: group=1 callgroup=1 pickupgroup=1 But on internal and incoming calls if I dial *8 from any phone I cannot pickup. Do I need to add

Hi folks, Recently we assigned our users agent id's and switched to having them use agentcallbacklogin instead of just ringing the phones directly.... it's been going well for the most part. Before we gave the users agent id's we had their sip configuration set to incominglimit=1 for one line on their phone, to prevent call waiting beeps. If they wanted to pick up while already on a

I'm using "insecure=invite" with two different dial plans, it it working with one dial plan but not with the other. What other parameters could influence "insecure=invite" In sip.conf below "insecure=invite" is working OK [pstn-1270] type=friend secret=spa3k username=voice-1270 mailbox=369 host=dynamic insecure=invite canreinvite=no disallow=all allow=ulaw

Hello. I'm new with asterisk. Can you help me in this: I have cisco sip phone (601) connected to asterisk server, and 1 client number (500). I want to dial from 601 to 500. But get error in cli console: [Apr 27 15:30:15] NOTICE[9650]: chan_sip.c:20059 handle_request_invite: Call from '601' to extension '500' rejected because extension not found. What's wrong?

Sorry if this show up twice, yesterdays post did not show up. We are having trouble setting up two ext's on one phone. We have it the point where the first two lines are ext 4000 then the third line is ext 4013. We can receive calls to both ext's but we can't make out going calls on ext 4013. The other thing that is strange is we need to have ext 4013 at the top of the config for ext