similar to: Eicon Diva and incoming Fax

Hi; I've got an AAH installation where a customer wants to install an active Eicon DIVA BRI card. AAH is built on Centos 3.5 which is currently at kernel 2.4.21.37. Support for Eicon active cards is built-in. I've debugged and run the A@H install-Eicondiva script but when I try to run divactrl load -c 1 -f ETSI -Debug I get a response : A: can't get card type for DIVA adapter

Hello, I have an issue getting the chan_capi module to load in asterisk cvs from today. Plain 2.4.20 kernel with melware patches for the Eicon Diva Server Bri card. I load the modules with: modprobe -v divas divacapi I load the firmware with: divactrl load -c 1 -f ETSI -vd6 Output in /var/log/messages is: Nov 9 19:26:26 voice kernel: Eicon DIVA - DIDD table (http://www.melware.net) Nov 9

Hello everyone, I'm having some errors while compiling the source code for an Eicon Diva BRI card. I am using Fedora Core 6 with a compiled from source Linux kernel 2.6.19. I have downloaded the Eicon Diva source RPM (divas4linux_EICON-106.12-1.i386.rpm) and installed it already. When I go to /usr/lib/eicon/divas/src/ and run ./Build, everything starts correctly until that part where it has

Dear list, I need to setup asterisk to send and receibe fax. I just looking about SpanDSP, Hylafax/Iaxmodem, AsterFax,...etc. The asterisk box has Digium hardware, one TE420B and one TDM2402 (8 FXO ports). I just read the SpanDSP (txfax and rxfax) makes the system more unstable that Hylafax/Iaxmodem. And the Asterfax solution does dislike cause its licensing. The TE420B, is configured in E1

Hey guys This is probably for Armin, but I thought maybe someone else might have something I could try. I'm having a problem with one of my Eicon Diva V-4BRI cards and I'm trying to work out if its a driver configuration error, card failure or telco problem: I have an Asterisk box running -- the Eicon drivers see all four ports on my card, capi.conf is configured with all four ports

Hi list, Does chan_capi work with kernel 2.6? The Eicon Diva server card loads fine judging from /var/log/messages but Asterisk gives an error when trying to load the chan_capi module. I'm using chan_capi-0.3.5, zaptel-1.0.0, libpri-1.0.0 and asterisk-1.0.0 on a Fedora box with kernel 2.6.8-1.584. Zaptel and ilbpri work fine as does *. I have seen a msg that may be related and don't know

Hi (Armin)! Does someone knows how to identify the type of the card? The delivery note says it is a V-4BRI-8M, whereas lspci reports a 4BRI-8M. What is it really? Are there any Eicon tools to identify the card type? thanks klaus 0000:0a:03.0 Network controller: Eicon Networks Corporation Diva Server 4BRI-8M Rev 2 (rev 01) Subsystem: Eicon Networks Corporation Diva Server 4BRI-8M Rev

We are experiencing slightly distorted audio with playing of recordings on our Asterisk server when the call comes in over our Eicon Diva Server BRI card. An example is an incoming call to IVR and playing some of the standard Asterisk voice prompts. Note that there is no audio problem with internal access to the same recording. Neither is there a problem with calls not involving the playing of

Hi, I'm trying to get an Eicon Diva Server4BRI card running under Ubuntu 6.06 - by downloading the v3 driver package from Melware and compiling everything. Yet, after activating the necessary modules (divas and divadidd) and interactively configuring the card (/usr/lib/divas/Config), starting up the adapter fails! The error "/usr/lib/divas/divactrl load -c 1 -Debug" produces

I have read most of Eicons information on Q.SIG, and I am able to load the Q.SIG protocol (instead of ETSI for example). No strange logging in divacrtl mlog. But how do I tell Asterisk to understand Q.SIG? My PBX is configured for QSIG, but I cannot see anything on my trace when trying to make a call via the S0(Q.SIG) Janne > -----Ursprungligt meddelande----- > Fr?n:

Hello all, I'm having problems getting chan_capi 0.3.5 to work well with an Eicon Diva Server card using using the driver from linux kernel both 2.6.10 and 2.6.12 (vanilla versions). I have a (really two) producci?n system(s) running chan_capi in another identical Eicon Card using kernel 2.4.27 and the Diva Server drivers from Eicon. I installed an compiled the source level rpm

I am trying to use chan_capi with an Eicon Diva Server BRI. I installed the Eicon drivers from source including CAPU and I can use the board correcly using tty_test and minicom over /dev/ttyds01 or /dev/ttyds01. I need to insmod capi ( why? it is not written anywhere) and then capiinfo shows me all board parameters, but I have to break it otherwise capiinfo doesn't exit at all, but I don't

Hi *, I want to integrate the Eicon Diva 4Bri Card to Asterisk. Eicon drivers and capi is installed. I use the latest dev version from eicon compiled and installed for my fedora 2 system. I found the chan_capi for asterisk from www.junghanns.net. Also loaded the patch and applied to the chan_capi source tree. I changed the Makefile to include the capi20.h from eicon:

Hi, I would like to set up a high density FAX/PBX server, am looking at using Eicon Diva E1 card with Asterisk and Hylafax sharing channels, is this possible. I know Extensions can be reserved for voice OR fax with the combination of chan_capi used for * voice, capi4hylafax on fax but then channels must be dedicated rather than shared ie. would like to be able to answer voice/fax on same DID.

Hi! I have some (short) question about the Eicon DIVA (V-)4BRI cards I want to have (short) answered before buying the DIVA card. I know there are several Eicon guys active on the list, thus I ask on the list instead of directly to Eicon so that all other will benefit as well. 1. Do Eicon DIVA (V-)4BRI cards support TE and NT mode? 2. Can the clock (master/slave) be configured independent

Hi! I've bought the EICON DIVA V-2BRI card an begin installation soon. Are there any issues with certain kernels? E.g. the standard debian kernel 2.4.27-2-386 and kernel-image-2.6.8-3-686. Further current kernel 2.6.16.14 would be an option. Thanks Klaus

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

Hello, I'm thinking of deploying Asterisk. I already have a handful of EICON Diva 2.01 PCI ISDN cards. I was thinking if it's possible to insert 4 such cards to my PC-Asterisk server (which I yet have to install) and use them as 4 lines in case anyone has to call me in / I have to call out using ISDN line(s)? Any reply appreciated. Tomek

Hello Marc, Could you post the install details for the Diva PCI? I have a Diva Pro PCI 3.0 and I am looking to get it working... I am running Debian Testing. So far it appears there are a few things floating around but I am not certain which direction to go. I know I need to load the firmware first. I did manage to load the modules ok. Thanks, Greg -----Original Message----- From:

Hi! I'm trying to enable echo cancelation with my Eicon Diva Server 4 Bri card. I've enabled it from zapata.conf, (as I read from www.voip-info.org) ------------------------------- ; Enable echo cancellation echocancel=64 echocancelwhenbridged=yes echotraining=2000 ---------------------------- but nothing seems to change, echo is still present. Any idea? Should I enable/change something