similar to: Asterisk Dropping Calls

> > Hi, Remove usecallingpres=yes busydetect=yes from your zapata.conf file. and the restart asterisk. Hopefully you will not faced drop call issues. Regards, Vidura Senadeera. Message: 3 > Date: Mon, 24 Sep 2007 12:29:40 +0100 > From: "Richard Young" <Richard.Young at intrintech.com> > Subject: [asterisk-users] Asterisk Dropping Calls > To:

I figured it out. The old system (Televantage 3 and 4 I think) has limited specifications on the T1. After setting up the system, I was able to send and recieve calls. I still have some work to do like figuring out faxing and a floating receptionist, but this is a nice start. ----------------------------------------------------Televantage T1 Requirements: Framing: D4 Superframe or Extended

I just had a user report that they called out to someone on a cell phone this morning, and after a short conversation, the call was dropped/lost. The person on the cell phone says that this is very rare, and would not suspect the dropped/lost call to be on their side. I have looked at the asterisk/full log as thoroughly as I can, and have pasted the lines which seem relevant to that call below.

Hi, We have a PRI Trunk (physical E1) and we are getting some rather weird and very isolocated problems. On outbound calls to specific numbers, it would seem to me that DTMF from the remote side is affecting the local asterisk system. Basically what happens: - We make a OUTBOUND call via the PSTN (PRI Trunk) to a remote System - Remote Answers, and converse - Remote sends DTMF on their site to

Hello List, I am having a strange issue with a trixbox system we installed for a client, and I would appreciate any help on this one. The issue is that occasionally when they go to answer an inbound call from the Sangoma A200 - there is no one there, and they are presented with dial tone. The calling party is hung up. A bit of background: The client actually has two systems install (one at

Hello, This is my first asterisk installation, and having read up on the documentation, and trying several tutorials i'm unable to get my outbound route working. I'm certain it's an issue with my configuration and my inexperience with asterisk. So i have my POTS phone connected to my digium card, and when i make a call, I receive the "cannot be completed as dialed" message.

[also posted on Trixbox trunk forum] I am also working with Sangoma directly to debug this, but so far no real luck. TrixBox 2.6.1, A102d card with V33 firmware (latest) and WANPIPE 3.2.6 (3.2.7 is out, but nothing has changed that would affect this problem). The system gets about 200 calls inbound on the trunk, which is not very heavily used, and of those calls one or two a day is randomly

I have posted my problem on the link below, but didn't get any answer. I am hoping someone here can help me with this issue. Here's my problem: I am using H323 to talk between Asterisk and Avaya IP Office 500. For some strange reason, when we are talking on a VoIP call, we get disconnected after 10+ minutes. We have two other Elastix box, but none of them are getting disconnected. From

Hi people, I have a problem with some extensions. The calls are ended after 31/35 seconds, also, it depends on the number which I call. This is the log, but I've not been able to find something wrong... Any ideas? [Jun 11 15:50:46] DEBUG[26071] app_macro.c: Executed application: ExecIf [Jun 11 15:50:46] VERBOSE[26071] logger.c: -- Executing [s at macro-dialout-trunk:16]

Hi, We are using asterisk 1.4.34, ubuntu 10.4, below is suspicious activity recorded in our full log. Could you help us to explain what had happened. Thanks. === my friend, 801, from his room did a test by dialing echo test in freepbx, *43: [Aug 20 14:42:46] VERBOSE[14427] logger.c: -- Executing [*43 at from-internal:1] Answer("SIP/801-000003f5", "") in new stack [Aug 20

Hi all, I'm new in asterisk and I got to set up a dundi config for my work. I have 2 PBX for the test, the two PBX are in the same local network PBX A : 192.168.199.23 PBX B : 192.168.199.21 my config files : (on PBX B , the config files on PBX A looks like it) /etc/asterisk/dundi.conf [general] bind=192.168.199.21 port=4520 cachetime=5 ttl=32 autokill=yes entityid=00:30:18:4C:33:53

Hi!I've a problem with asterisk,it doesn't start..it's stopped..I used the amportal start command and this is the result: SETTING FILE PERMISSIONS Permissions OK STARTING ASTERISK Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk. Asterisk ended with exit status 1 Asterisk died with code 1. Automatically restarting Asterisk.

Hello - I've read Asterisk should be able to activate a do not disturb feature to turn off the ringers on extensions. I checked the wiki and can't find documentation for how to do it. Here's my attempt, added to extensions.conf: [dnd-on] exten => _#78,1,Answer exten => _#78,n,Wait(1) exten => _#78,n,Macro(user-callerid,) exten =>

I am using Asterisk 11.17.1 with my program that uses AMI Originate calls to generate a bunch of calls for a callcenter. The PBX configuration is handled by FreePBX 2.11. I want to understand the dialplan behavior in order to figure out why the CDR(recordingfile) is blank on the CDR records despite the dialplan setting it. My program generates the calls by setting Channel=Local/NUMBERTODIAL at

Hi list! I have this configuration for sending T38 faxes to my T38 fax termination provider: T38modem --> hylafax --> Asterisk-SIP-Extension --> T38 termination provider --> T.30 termination to PSTN We are experiencing 2 problems with this (if you want configuration files, it won't be a problem, just tell me): 1. T38 termination provider receives faxes at 2400 bpps from our

Hi all, I?ve ran into a problem regarding D-channels. I have setup Asterisk (CVS-HEAD-03/21/05-16:41:57) on RH Fedora Core 3(2.6.10-1.770_FC3) I also have a digium wcte11xp card for connetivity to the PSTN(E1). When I start zttool i see that Current Alarms changes between Recovering and Blue Alarm/Recovering. I started to see these problems after i moved the digiumcard from one PCI slot to

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Asterisk 1.0.9, Copyright (C) 1999-2004 Digium. Written by Mark Spencer <markster@digium.com> .... [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 16 20:36:51 ERROR[6750]: chan_zap.c:6246 mkintf: Unable to get parameters Sep 16 20:36:51 ERROR[6750]:

I have two servers, each connected to the PTSN via PRI. When I call from site A (951-999-9999) to site B (555-1212) and the phone at site B is on the phone, I hear the normal ring tone for about 20 seconds, then the message "all circuits are busy now. please try your call again latter" followed by the congestion tone. Instead, I want this to busy ring and then hang up without any

I have spent some time this morning trying to add an Astribank to our current Asterisk, but it failed, so I just removed the hardware, restore the config files to the original setup and started asterisk.; I could see that no Zap channels are started so I did load chan_zap.so: pbx*CLI> module load chan_zap.so [Feb 26 10:32:18] WARNING[3809]: pbx.c:2968 ast_register_application: Already have an

I have a trixbox 2.2 and Nortel santral that are speak each other. I use digium TDM100M 2 fxs-2fxo. After I made yum update I had met with some problems when I want to make any call from extension of trixbox to extension of nortel. When I attend to log (/var/log/messages) I meet with these messages as you see below. When I try to make any call from trixbox extension the call seems established but