similar to: Zap channels: no sound with certain call paths

[also posted on Trixbox trunk forum] I am also working with Sangoma directly to debug this, but so far no real luck. TrixBox 2.6.1, A102d card with V33 firmware (latest) and WANPIPE 3.2.6 (3.2.7 is out, but nothing has changed that would affect this problem). The system gets about 200 calls inbound on the trunk, which is not very heavily used, and of those calls one or two a day is randomly

Hi all, I have a connect between a siemens hipath & Asterisk system over PRI The connection works perfectly I can call from the Hipath to an Asterisk Extension. I want to allow the hipath extensions to dial out over a SIP trunk on asterisk but I keep getting "The number you have dialed is not in service" In this CLI I'm dialing from hipath extension 9 (prefix for sip trunk)

Hey everybody, I've, within the last 3 weeks, moved over to a PRI from SBC/AT&T. I've received several complaints about dropped calls. Reviewing the archives on PRI and dropped calls shows that I should set the resetinterval=never in the zapata.conf and restart. This hasn't helped. The dropped calls have to date only been on outbound calls. Usually within 2 to 3 minutes

We have an asterisk box with the following configuration: - AMD Athlon XP 2400+ - 512 MB RAM - SUSE Linux 10.1 - a Digium card TDM400P with 3 FXO - another Digium card TDM400P with 4 FXS - asterisk 1.2.7.1 - zaptel 1.2.4 I already checked that those cards aren't sharing interrupts (by cat /proc/interrupts): 0: 14119786 XT-PIC timer 1: 10 XT-PIC i8042 2:

I've been monitoring this problem for almost a month now. I realized that it is more extensive than what I described previously. I can very easily replicate this problem on every Zap channel. Following is the senario: 1. Call Zap/5 via say SIP/15 -> Zap/5-1 created and starts to ring 2. Call Zap/5 via say SIP/21 -> Zap/5-2 created and starts to ring 3. Hangup SIP/15 ->

Hi What causes deadlock? Apr 5 14:02:43 WARNING[2413] channel.c: Avoided initial deadlock for '0x82acb10', 10 retries! Apr 5 14:02:43 WARNING[2413] channel.c: Avoided initial deadlock for '0x8298160', 10 retries! Here is the portion of the log: Apr 5 14:02:42 NOTICE[23363] chan_zap.c: Got event 18 (Ring Begin)... Apr 5 14:02:42 VERBOSE[23363] logger.c: -- Executing

Hi, Does any one experience that SIP phone to SIP phone (Polycom phone) calls can't hear each other, but Monitor application records both end's voices. It also happens in group pickup calls. Zap calls to queue (Local channel) also experience this problem (sometimes, our SIP phone can't hear any voice from incoming Zap calls when pickup, sometimes this happens after 10-50

I'm seeing both inbound and outgoing call failures on our ISDN-30 lines that only seem to go away when I do a "zap restart" or in extremis restart Asterisk (1.4.25 with a Digium TE205P and zaptel 1.4.12.1). If I don't restart zapata or Asterisk the problem rapidly get worse :-( The lines are from BT with LCR from Cable&Wireless (I've tried using the LCR bypass code and

Hi, all. I've got app_rxfax going and nicely receiving a fax, which I then throw to a script, and have it convert it to a PDF and mail it. Works great... a lot of the time. But a fair bit of the time, rxfax throws errors, and extensions.conf seems never to invoke my script. Here are the pertinent lines: exten => _6403,n,rxfax(${FAXFILE}) exten =>

Hello, This is my first asterisk installation, and having read up on the documentation, and trying several tutorials i'm unable to get my outbound route working. I'm certain it's an issue with my configuration and my inexperience with asterisk. So i have my POTS phone connected to my digium card, and when i make a call, I receive the "cannot be completed as dialed" message.

HI, I have 2 TDM400s plugged in a PC. I failed to use same channels to make a call to PSTN. It shows it can't establish connection after dial command issued. Below is the log. Actually, the call is established as I can hear voice from the called party but the softphone is still showing ringing. It seems the TDM card can't get an answered signal from PSTN. After 15 seconds, the call

Hi. I am using asterisk 1.4 (latest as of today) and zaptel 1.4 (latest as of today) and I cannot dial out using my 400P card with one fxs module and one fxo module. I am using kernel 2.6.24 and get the following log entries: [Feb 25 17:28:13] VERBOSE[25071] logger.c: -- Executing [s at macro-dialout-trunk:23] Dial("Zap/1-1", "ZAP/4/www411|300|wW") in new stack [Feb 25

Hey everyone, A few employees have noticed some problem here and there when trying to make outgoing phone calls. After it happens, they try again, and are able to call through. The dial plan for outbound calling looks like below. Which I know they are getting to the Congestion part (which explains the busy) but what I can't seem to figure out is the cause for why they are getting sent

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hi guys, I spent a couple of hours in Google, but the problem appears to be uncommon, so I'd like to ask about it here. The problem is exactly the opposite to "Asterisk does not detect FXO hangup". In my case it's the Telco who does not appear to be detecting Asterisk's hangups. Telco is Telus in Vancouver, Canada. The setup is very simple - Telco -> FXO/TDM400p

hi, after upgrade from 1.0.x to 1.2.x i cannot send faxes my topology: PSTN<-wct4xxp-asterisk- -sip- ata (ht496,ht488,asus vp100) - samsung sf2500 fax log: Feb 13 23:50:35 DEBUG[27914] chan_sip.c: Allocating new SIP dialog for 20d700003cb20000@192.168.1.209 - INVITE (With RTP) Feb 13 23:50:35 DEBUG[27914] chan_sip.c: **** Received INVITE (5) - Command in SIP INVITE Feb 13 23:50:35

Hi, Urgently response would be wonderful, system is a Fedora Core 2. I have a Ericsson BP250 connected to 1 port on the TE405P and another connected to a local telco ISDN30. I have been running CVS-HEAD from about a 2 months ago and upgraded it again just in cause it was a version issue (didn't fix it) but this is what I am getting. When a person calls out from an extension on the BP250 to

Using tdm400. While transfering a call from outside to another extensions, while this "outside call" is waiting with music, the "another extension" call hangs up suddenly, and the call is back to the "outside call" suddenly. Wathcing logs: Jan 15 13:32:44 DEBUG[30148] res_musiconhold.c: Read 462 bytes of audio while expecting 640 Jan 15 13:32:55 DEBUG[27850]

Hi asterisk-users, We are using Asterisk 1.2.12.1, and are trying to use the Page application. It seems to work but after approx 4-5 seconds the call is hung up. The dialplan code look like this: exten => _*2XX,1,AGI(get-paging-devices.agi,${EXTEN:2}) exten => _*2XX,n,GotoIf($[ "${PAGING_DEVICES}" = "invalid" ]?i,1) exten => _*2XX,n,SIPAddHeader(Call-Info:

Hi, I have a strange problem. I have a TE110p digium card. I want to dial 19173995791 when any incoming call comes in. What is happening is that when I dial 19173-995791. Asterisk picks up the first 5 digits assuming it is the extension and appends 212-85 (here in the university most numbers start with this) in front . Therefore I get connected to some random number 212-85-(19173) (where the