similar to: Cisco FXS Issue...

All, I need to run this by everyone and see if someone has any idea's. I have a asterisk server setup and currently am receiving the inbound calling number where the name should be. My setup is.... One pri terminating into a Cisco 2431 router Sip messages from the Cisco get sent to a asterisk server linksys ata's a each remote end. I can receive the calling name if the call originates

What is the recommend Digium Card for a PRI in NA ? I want to interface a Asterisk Server to a Samsung iDCS System, and have available T1 w/DNIS, or a PRI w/DID, the asterisk server would need to appear as a "Telco" provided Circuit. Slot Availability. Four PCI-Express Slots x8 (1 full-length/1 half-length/2 low-profile).

I'm having trouble getting an Asterisk server to make outbound calls on my iDCS Trunks. I have idcs station to asterisk station working I have asterisk station to idcs station working However, I am unable to get Asterisk to utilize any outbound trunks on my iDCS.... Anybody have any ideas? ________________________________________________________________ Sent via the WebMail system at

Any Recommendations on a "Good" Wireless Voip Keyset that works well with Asterisk? I would prefer one that is IAX2 as it works better behind a Nat'd Firewall.. But I am reaching out to you guys as you all would know what would work the best :-) ________________________________________________________________ Sent via the WebMail system at kotbh.net

I am trying to determine what would need to be done/modified to enable the following: I have a SIP extension come into my asterisk box, and I then need it to call "6-10" remote Sip Stations that are set to Auto-Answer... (note, my remote sip stations are actually cisco h323 devices, I can call them fine from any softphone, or other device, and have full-duplex audio, however, i need to

How well does the Grandstream GXW-4104 or (8) work w/Asterisk? I would use a Cisco Switch w/FXO Ports but that would be a little "Pricy" I Can't use a Digium FXO Card, as the asterisk Server is offsite. Thanks, William Stillwell KI4SWY ________________________________________________________________ Sent via the WebMail system at kotbh.net

Hello, Has anyone experienced a segmentation fault in asterisk for using G729 against an AS5300 in SIP ? I'm having this problem. Also, any other codec I use gives me incompatible media (can be read in SIP DEBUG messages). AS5300 configured for multiple codecs, so is Asterisk. Tried G711u/A G723 and G.729. Any clues ? Regards, Jorge A. Info: Asterisk ver 1.0.7 stable Using AMPortal

Hello, everyone. Right now, we are trying launch our own PBX system based on Asterisk(Fedora) with Cisco 2611. Cisco has 2 port FXO card installed on it. For testing, I have 2611 hooked into phone line with number of xxx-xxx-xxxx fine. (I'll call it F). Using softphone, I can dial in extension 1001 on asterisk, which should talk to cisco. After initial connection to Asterisk, I have try to

HI, I have been pulling my hair out trying to get a Cisco MC3810 to interface my Asterisk box with a T1. I am able to make outgoing calls but incoing calls never reach my Asterisk box. The cisco give a fast busy when I try to call one of the DID's. When playing around with the dial-peers I can get the cisco to pick up the call, but then it forwards the call back to the ANI that is dialing.

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

What are people's thoughts on asterisk 1.2.26? Any show stopping bugs? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080117/57d1002d/attachment.htm

Folks, I have a NEC 2400 pbx(non-voip) behind a Cisco 3725, connected via standard wic-t1 card. The NEC needs to call two different asterisk servers with 4 digits. I have two way calling working with the one * box, but the other is perplexing me. Here's the layout * <--> Cisco 2811(192.168.13.1) <--> 1.54 point to point <- Cisco 3725(192.168.8.1)<-> NEC 2400. The

Hello Has anyone been able to get the Soyo G668 phone to work with Asterisk? I've been playing with it for two days and I haven't had any luck. I've got a soft IP phone(xten) to work fine. If anyone has a sample config page that would be great. Thanks Aaron -------------- next part -------------- An HTML attachment was scrubbed... URL:

Has anyone had any experience with the Soyo G688 phone? I'd like to use it as a agent's phone. Is it reliable? How well does it work with *? How's the quality? Features? Thanks, Waldo

One system I have is configured thusly: AMD Duron 1200 (I have frequency restrictions in this application, and must stay below 1.3GHz or must be above 2.0GHz, and the 1200 fits nicely in our interference plan; besides, I was given the chip, and it's fast enough for the application). Soyo DRAGON KT400 motherboard, 512MB DDR RAM (DDR266). Silicon Image SATA interface card. Machine boots

oops. I successfully installed RedHat 8.0 onto two ATA133 80gig drives running a mirrored RAID with the hpt37x (highpoint 372 onboard RaidController on the SOYO DRAGON motherboard.) I used ext3 as my filesystem type of choice but unfortunately the system shut down uncleanly and it now is coming up with the "press Y to force file system integrity check" at boot.... which it runs by

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Having a workstation with an odd glitch, and I'm hoping someone can help. We have a 35MB shared Excel file with our purchasing history in it. (I know, I've been trying to talk them into a database of some sort, but they'll have none of that...) One workstation in the entire plant is having issues opening it. The file will load, it will

I wouldn't expect you to be using RFC3389 if your using A-law, can you include your IOS version and IOS config file ... I have not specified any allow's or disallow's in my * config for the codecs with my 5300, I also use Cisco 79xx phones and I use the option within the phones config file to select the preffered codec and when I change this to G.729/A-law/U-law all works perfectly

Hi, I'm trying to get a remote Cisco Call Manager Express (CME) system behind a dynamic IP address routing both inbound and outbound calls via SIP to my local asterisk server. I've got a local CME system working fine on the LAN, where the CME is at a static IP (host=10.5.7.130 in sip.conf), but I can't figure out how to get it working with host=dynamic, even locally on a test

I'm really, REALLY hoping someone can shed some light on this. I posted something similar about this but I got more confusing info from my LAN people. The hardware is a Soyo K-333 Dragon MB running SuSE 8.0 w/Apache2 & Samba. I have 2 NIC's, the onboard NIC and a D-Link 530TX+ card. I have two IP addresses, 155.16.78.54 & .55 on eth0 I get lots of collisions, errors, etc., and