similar to: FW: Can you reload only one conf file?

I've not needed to do a dialplan reload for a while, so I don't know exactly which version is stopped working, but on 15.5, I'm not seeing ANY debug info at any debug level. So I'm not really sure how to find mistakes in the dialplan. This is all I get... how do I enable this debug mode to see the previous behaviour? Thanks asterisk -rvvvvvddddd (enters console) dialplan reload

Hi, I'm a little confused over what I'm seeing when a source file is overwritten whilst an rsync is in progress. Instead of the destination file being truncated, or an error being raised and the destination file removed, I get a file of the correct length, but mostly full of nulls where previously there were none. An example is shown here: > ls -l big_file -rw------- 1 jonm users

I hope I have this wrong, but when I have a bunch of priority 1 NoOp's created from regexten in sip.conf, and I do an 'extensions reload', I lose all the priority 1 NoOps! This can't be right... this means that in a production environment, if you make a change to your dialplan and do an 'extensions reload', you lose your ability to terminate calls to phones on this system.

Whenever I issue the reload command, asterisk crashes. Below is the output I get from (gdb) bt Any help is appreciated. *************************************************************** *CLI> reload == Parsing '/etc/asterisk/manager.conf': Found == Parsing '/etc/asterisk/enum.conf': Found == Parsing '/etc/asterisk/rtp.conf': Not found (No such file or

Hello. I have been beating my head over this problem for about 6 hours now. I have a SIP peer, who I register to (successfully), who should be directing all incoming calls at my [default] stanza in my extensions.conf: [ Context 'default' created by 'pbx_config' ] 's' => 1. Wait(1) [pbx_config] 2.

Howdy, I'm building a webapp to allow my techs to do minor dialplan edits and trigger a reload on my PBX's running 1.8 I have no problem triggering a 'reload pbx_config.so' via manager, The problem is how can I see the results of my reload? For example a missing close parenthesis which would show in /var/log/asterisk/messages [Apr 10 13:46:16] WARNING[23911] pbx_config.c: No

Hi, I have a trivial peace of dialplan for exten 100. I try to change it to _1XX and the asterisk act according to a different (Default??) dial plan and not the one I want? Is that possible? Where is the other dialplan sits? In my extention.conf I can't see something that look like what asterisk is dialing. How can I trace\debug my dialplan? Thanks, Eyal -------------- next part

I just tried this in my extensions.conf exten => **,1,Noop(Testing) exten => **,n,Playback(demo-congrats) Did a reload... and the above does not happen. I created as 12 instead of the ** and that works fine. Is there anyway to get the ** to work? I also am using a polycom phone if that affects things. I'm using asterisk 13.15.0 Thanks Jerry -------------- next part --------------

Address 0xfffffffe out of bounds why and how to solve.MyConfbridgeCount(conferencenumber,variablename )return total number of user in conference given by conferencenumber otherwise zero.At runtime using MyConfbridgeCount(4000,count ).now app2: MyConfbridgeCount will call function count_exec(struct ast_channel *chan, const char *data).But at compile time char * data cause core dumped.

Hello I have 2 strange errors when using the Background()-application and DTMF-input that is received. First of all, my first 2 lines are not being executed. The first line being executed is the Set() application, thus line 3. Secondly, the received digits (911) is not the same as the EXTEN (which is set to 91). exten => ivr,n,Set(TIMEOUT(digit)=2) exten =>

Hi. I'm developing a command line tool (a GUI is following) for easily sharing local directories as an unprivileged user. After adding shares smbd reloads its config file (via SIGHUP). Under Windows new shares appear immediately. If removing a share, samba reloads the smb.conf but it has no effect on established connections. I can still access the share even though it has been removed.

On 4/13/16 11:57 AM, A J Stiles wrote: > You could try > *CLI> dialplan show Between my older backup and dialplan show, I guess that's my best shot. Thanks :D

I've made a change to my manager.conf file in asterisk 1.2.18 Is there a way to reload that config file from the CLI without restarting asterisk? Bob

Hello, I noticed Asterisk 1.8.4.1 execute number dial twice Log == Using SIP RTP CoS mark 5 -- Executing [912066604 at sipphones:1] Set("SIP/4773-0003e920", "CALLERID(num)=2066604") in new stack == Extension Changed 4773[sipphones] new state InUse for Notify User 4701 -- Executing [912066604 at sipphones:2] Dial("SIP/4773-0003e920",

Good morning, We recently fell back to the most recent build of asterisk 1.8 down from 11.3 and I believe we've crossed some sort of limit for 1.8. Our dialplan is 515723 entries long with 6263 distinct contexts. Both are loaded realtime via odbc (mysql). Previously at the end of a dialplan reload we would get a summary of how long it took to reload everything. Now it just shows the last line

I have a dial plan that includes a company phone directory as a main menu option. If they just sit at the main menu, after 20 seconds, they are transferred to the operator. If the user picks an extension from the directory, they are transferred to the proper extension. If the called number is not available, they are transferred into VoiceMailMain. They leave a message, and hang up. The hang

Hello All, I was wondering where does Asterisk stores the blacklist numbers? I looked into the dialplan and it shows that it *"Set(DB(blacklist/${blacknr})=1)"* the number... Does it save in MySQL DB? hyperion*CLI> show dialplan app-blacklist-add [ Context 'app-blacklist-add' created by 'pbx_config' ] '1' => 1.

Has anyone implemented "hot seating" in any neat way? This where people can log in to any phone in the company and have their calls/voicemail come to that particular handset.....

Hello everyone... I'm trying to get up a testing pbx installation. Following instructions of what've read from the handbook and from asterisk's wiki, I wrote the dial plan as follows: [general] ; ; static = yes ;[globals] ; [default] ; exten => 0,1,Answer() exten => 0,2,Playback(fcopba1) exten => 0,3,Hangup() exten => *0,1,Answer() exten => *0,2,Record(fcopba1:gsm)

When I first to the "add extension" the "show dialplan" has the lines that say "SIP/" but after I do a "save dialplan" and a "stop gracfully" and restart the lines with "SIP/" are gone. ************************ "Show dialplan" before: ************************ asterisk01*CLI> [ Context 'default' created by