similar to: No subject

Hi I am trying to get H323 to run on Asterisk, basically I had Asterisk running so I followed this tutorial http://astrecipes.net/index.php?n=286 and got h323 to run on my first server on the second server it is just throwing the error: ERROR:Failed to create H323 listener The whole error is : ERROR: Could not open H.323 listener port on 1720 [Oct 13 09:20:48] ERROR[3608]: chan_h323.c:3166

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hi, My configuration is SipPhone<----->asterisk1 <----->asterisk2. My asterisk version is 1.2.10. I installed chan_h323 according to 'http://astrecipes.net/?n=102'. When i call from asterisk1 to asterisk2, there is no audio. Using 'rtp debug', I can see that rtp packets are being received. Regards, Jason. #------h323.conf for both------------------------ [general]

Hello, I have a strange h323 issue. After executing command "Dial("SIP/333-0d1dfe00", "H323/361737052390920 at ccg|5|tT")" at Oct 18 22:32:23. Meanwile I have sniffing traffic on port 1720. The call was established just at Oct 18 22:33:03 (New H.323 Connection created.) and also packet sniffer grabs the h323 invites at this time also. So my question is what

Hello, I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. My network connection diagram: ---------------------------------------------- X-lite/X-Pro-->Asterisk--chan_h323-->GnuGK--->AS5300-->PSTN boldsoft*CLI> show version Asterisk CVS-v1-0-03/24/06-15:27:08 built by root@boldsoft on a i686 running Linux I can make

Here i am doing a dial command from a php agi... EXEC DIAL H323/123456789@xx.xx.xx.xx:1720|40|HL(585000:61000:30000) But asterisk is not disconnecting the connection after 585 secs... the result is ... answered time is 1926n but thing is time out is working some time and some time not.... LOG: 2005-06-28 20:26:13 VERBOSE[19094] logger.c: callcard.php: string(111) "app_callingcard:

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

I'm trying to use a Howlink CL-100 ip phone with * It's h323 phone with very limited protocol support. But it's enough that I can use it to dial netmeeting client and artisoft pbx just fine. When I try to dial my * with it using either chan_h323 or oh323, it seems to fail on negotiating H245. Maybe this phone doesn't support it? I've used all different versions of

Actually I am facing a problem with H.323 (the standard and the ooh323) with Asterisk vesion 1.4.25 and I discover the following: 1) Using the standard h323 that come with Asterisk: The chan_h323.so it is not existed in the /usr/lib/asterisk/modules after doing the compilation and installation for (pwlib, openh323, /chanels/h323, asterisk), although make menuselect was done and the h323 channel

Hi, My configuration is SipPhone<-->*1<--->*2. My asterisk version is 1.4beta3. I installed pwlib,openh323,chan_h323. When i call from SipPhone--(SIP)-->asterisk1---(H323)-->asterisk2, there is no audio. Using 'rtp debug', I can see that rtp packets are being received. Rtp packets are being exchanged. I also tested chan_ooh323, but to fail. Can anyone recommand best

I am using Nu Fone Network's h323 drivers. I can place H323 calls using following in extensions.conf file, exten => _1732.,1,Dial(H323/${EXTEN}@192.168.1.2) If I need to use h323.conf to do the same I cannot configure h323 to do the same. I get everyone is busy message and I do not see IP packets being generated by * trying to communicate to 192.168.1.2. Can someone point out what I

Hi all, I'm trying to trunk my asterisk with a cisco cme 3.3 using h323. Cisco conf: dial-peer voice 8 voip destination-pattern 2... session target ipv4:<asterisk ip> codec g711alaw no vad h323.conf [general] port = 1720 bindaddr = 0.0.0.0 ;tos=lowdelay ; disallow=all allow=alaw allow=ulaw allow=gsm context=from-internal extension.conf [from-internal] exten =>

Hi all, I try to ask helps again about chan_h323 extensions. I define this in h323.conf: [general] port = 1720 bindaddr = 0.0.0.0 allow=gsm allow=ulaw gatekeeper = DISABLE context=default [gm1] type=friend host=192.168.1.20 context=default [gm2] type=friend host=192.168.1.25 context=default and I have in extensions.conf : [demo]

Hello all, I just installed Asterisk with H323 support (chan_h323 from Jeremy McNamara). But experience problem while connecting OpenPhone to Asterisk Here is h.323 trace: 5:37.444 H323 Listener:9c86de0 transports.cxx(1504) H323TCP Started connection: host=10.120.160.15:3172, if=10.120.160.99:1720, handle=27 5:37.444 H225 Answer:9cc1250 transports.cxx(564) H225

[public_gk] ;exten => _070.,1,Set(CALLERID(number)=070333333${CALLERIDNUM}) exten => _070.,1,Dial(H323/${EXTEN}@59.120.139.119) exten => _070.,n,Hangup *CLI> h323 show peers Name Accountcode ip:port Formats 7000 ast_h323 203.160.252.147:1720 0x4 (ulaw) 88670333333 ast_h323 203.160.252.147:1720 0x4 (ulaw)

Hello, I'm trying to use the GSM codec with Nufone H323 but it's not working. Does somebody has some idea? Have I missed something? Thanks!! Celso Fassoni Some additional info: (I'm using CVS-HEAD - downloaded today) monkey:~# cat /etc/asterisk/h323.conf [general] port = 1720 bindaddr = 192.168.0.100 ; this SHALL contain a single, valid IP address for this machine

hi just after talking to Jeremy, I downloaded the source he's using and compiled. core dump! This was without gatekeeper: (gdb) bt #0 0x40141118 in mallopt () from /lib/libc.so.6 #1 0x401400fc in malloc () from /lib/libc.so.6 #2 0x405e981b in PAbstractArray::SetSize(int) () from /usr/src/pwlib/lib/libpt_linux_x86_r.so.1 #3 0x405ed006 in PString::SetSize(int) () from

Hi, Someone released a succefull interconnection in H323 with WTL equipement ? I'm trying to do that with an IPNx. But get dead air. With chan_oh323 it's fine, all works. With chan_h323 => dead air. The configuration is GW to GW. This is my configuration from h323.conf: [general] port=1720 bindaddr=my.ipaddr dtmfmode=rfc2833

I'm having a problem with chan_h323 compiling for Asterisk. RedHat 7.3 PWLIB 1.4.11 pwlib_1.4.11.tar.gz OpenH323 1.11.7 openh323_1.11.7.tar.gz [asterisk@jonux h323]# make clean rm -f *.o *.so core.* [root@jonux h323]# make cc -g -pg -c -o chan_h323.o -pipe -Wall -fPIC -Wmissing-prototypes -Wmissing-declarations -DP_LINUX -D_REENTRANT -D_GNU_SOURCE -march=i686 -DPBYTE_ORDER=PLITTLE_ENDIAN