similar to: No subject

And I'll resend this one too. Silly scalix. --Rob -----Original Message----- From: Rob Thomas Sent: Thursday, 22 June 2006 12:19 AM To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: RE: [Asterisk-Users] zapata.conf: recent changes? Looks like you've stopped compiling libpri. All those options that are being ignored, are being ignored because they're

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hello List, is someone operating a DID /P2P / Anlagenanschluss with more than one HFC-Based ISDN-Card ??? I have now 12 hours of setup-troubles behind me with Colt-Telekom, where we did not get it working with two HFC-based cards. Here the setup: - 2 HFC-ISDN-Cards (the one from Conrad-Electronic) - bri-stuff.0.0.2 (with the asterisk-sources from the download.sh-skript) - two NTBAs from

Hi All ... I'm running Asterisk 1.2.13-BRIstuffed-0.3.0-PRE-1v which has a Junghanns QuadBri card in it (lspci reports Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)) I have a regular KPN ISDN2 Line connected which works fine with the the zapata.conf below. However, I also have a new KPN ISDN Mutli (meervoudig) line (PBAX-Group), which works fine for incoming calls,

Please forgive me, if I misunderstand the problem completely. Following instructions in several german blogs, I want to configure Asterisk with a hfc-pci card, an old NTBA and an ISDN phone as a SIP device. It seems that I have to set signalling in zapata.conf to bri_net_ptmp. When I do this, Asterisk will hang if started with -vvvvc, the last lines of output being: [res_features.so] =>

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hi everybody, I'm facing a strange problem after upgrading Asterisk from 1.0.9 to 1.2.4. Sometimes, when receiving an incoming call from pstn, although my sip phones ring correctly (I've got both softphones and hardware phones), noone can pick up the call. Asterisk CLI shows me that the phones are ringing, then nothing happens, so there's no problem _after_ someone picked up, simply

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hello, I'm having problems making international calls from our asterisk using an ISDN30 in the netherlands. Below is the zapata.conf that works for all national calls, but international calls all fail a RC=41 ; zapata.conf [trunkgroups] [channels] language=nl signalling=pri_cpe switchtype=euroisdn callerid=asreceived ;pridialplan=unknown ;prilocaldialplan=unknown immediate=no

I still can't get this thing to work. Outgoing calls are fine, incoming just hangup straight away. I get a lot of & characters in my logs, I'm wondering whether they're caused by some sort of bad data ? Mar 3 16:03:01 VERBOSE[10437]:

I have a strange problem: if I put on hold an incoming call from my Digium TE110P, I can't resume it and the person at the phone continues to hear MOH until the line falls. My TE110P is connected with an italian E1 NT. If I put on hold a call on a SIP channel I can resume it without any problems. Is there someone that can help me? These are my configurations: zaptel.conf

Hi, I'm a newbie on * trying to setup an HFC card. I'm locked for many days getting the all-circuits-busy. And no idea what else to look for/how to diagnose. I'm in Spain, I've tried changing many parameters on zapata/zaptelcong with no luck, also NT & TE modes (honsetly, I've no idea what is). Any clue will be very much appreciated! I've installed *@home on my RH9,

Dear Customer Support, i connected the asterisk to a e1 interface of our hipath4000. outgoing calls from a sip peer of my asterisk to an up0 telephone which iss connected to the hipath4000 are working. If you want to dial from an up0 device to the e1 interface where asterisk is connected to, you have to use the prefix 83. But when you enter the 3rd cipher this error appears at the cli

Hi all, I just posted this question before last week. Meanwhile after upgrading Asterisk 1.0.7-BRIstuffed-0.2.0-RCg to 1.0.8-BRIstuffed-0.2.0-RCh the same problem occurs, but seems to be more seldom. Attached is now the output of "zap show channel" . - I'm running a stable Asterisk on a HP DL380G2 1.4Ghz 0,5GB RAM equipped with 1x TE410P and 2xJunghanns OctoBRI running in NT-mode.

I guess it is possible to have an HFC-S card and a Digium TE110P card working at the same time? The TE110P will work in E1 mode. I think the zaptel.conf is probably right but the zapata.conf not (I just tacked on another group at the end but I don't really know what I am doing). Can anyone help? ----------------------------------------- My zaptel.conf looks like this: # hfc-s pci a span

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Asterisk Version: 1.2.9.1 Zaptel Version: 1.2.6 LibPri Version: 1.2.3 Hey List, we are running an asterisk server in connection with an octopus telephone system. I have expired some random drops of zap channels bridged to SIP Telefones ( snom 190 ). Asterisk Messages shows something like that: Jun 9 09:32:33 WARNING[3207] res_features.c: Bridge failed on channels SIP/fon01-6945 and Zap/32-1