similar to: No subject

I need your help I have a sangoma A104D on my dell server; I got card status ok with no alarm If I dialed the extension 6210006, it shows the output as stated below, but there is no ringing from the pstn number nor the iax softphone am using on my pc. I will be glad if someone can give me a working config? What I want to achieve is to send all my call to the pstn on A104D? The pstn am

Calling out on PSTN over a TDM400P seems to generate a Red Alarm - whatever that is. I have another extension on the PSTN, and I can dial out over that. zttool shows no alarms. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 Fra Codi Options LBO Wildcard TDM400P REV I Board 1 OK 0 0 0 CAS Unk YEL 0 db

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

"RED: Loss of signal (LOS): The equipment shall assume "loss of signal" when the incoming signal amplitude is, for a time duration of at least 1 ms, more than 20 dB below the nominal amplitude. The equipment shall react within 12 ms by issuing AIS." This sounds like what is happening, and is in order with what one of the technicians said - I was about 20 dB below their

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

On Thu, 2006-03-02 at 11:42 -0600, Jordan Novak wrote: > Does anyone have a way to do wake calls? > > > > Jordan Novak > > Communications Technician > > Logistics Health Inc. You could use cron and /var/spool/asterisk/outgoing scripts to dial numbers, etc... > Can you elaborate, I am fairly new to Linux and a phone guy to boot. I am looking for a way for the

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hi guys, I've been trying to get my ISDN-10 line up for the past few days, but its been going up and down. I am using OpenVox D110P card on asterisk version 1.4.21. It seems to me like a cable problem. I tried using Ethernet straight cable (12, 45, 36, 78) and also a "straight" cable where the twisted pairs are on 12, 34, 56 and 78. The problem remains the same.

Hello all, I got a problem at an asterisk server, with dropping calls, losing all channels and reaktivating all channels and beeing back up. This problem seems to occure randomly over the whole day, when it gots traffic on the card. After looking @ google I found several hints but none did work fine. To avoid problems with the phone line (german E1) I called the provider, he did a 45 min. route

Hi everyone, I have a PRI conection on an * system running Asterisk 1.0.9, libpri 1.0.9 and zaptel 1.0.9.2 connected to an AXE 10 (APZ 21220 System 64) in the network side. I know the system and the wildcard I´m using are ok because I´ve used them before with other PRI connections (to a Siemens EWSD) without any problem. First the PRI didn´t work (I got the TE110P alarmed with red). After

I have configured TDMoE sucessfully and I am able to make a Zap connection from one box to the other. The question I have is.. I'm getting repeated errors every second on both systems.. Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 1: No Alarm Oct 3 09:53:16 WARNING[4409]: chan_zap.c:6252 handle_init_event: Detected alarm on channel 2: No Alarm

Hello, I'm trying to get a Wildcard T100P working with Asterisk and so far I haven't had any luck. No problems with the card itself from what I can see and the telco says that the problem is on our end (don't they always?). A small sample of what asterisk spews out on the console: Jan 13 15:45:32 WARNING[180236]: chan_zap.c:5834 zt_pri_error: PRI: Read on 43 failed: Unknown

Hello All, I have got my TE110P working at the hardware level, turned out to be a dodgy cable causing the Yellow errors in zttool. However, now I am getting yellow errors in asterisk, but zttool shows nothing out of the ordinary. here is my current config, and some asterisk console errors, any suggestions most welcome. zaptel.conf span=1,1,0,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31

Hello - I have a Premisys Slimline Channel Bank connected to a Digium TE110P. I am not able to call the FXS extensions or get dialtone on them. The channel bank is connected via a T1 crossover to the cable and lights show green. I really need to get this functioning by end of day. If anyone can help me out I would be greatly appreciative. Thanks, Dave zaptel.conf loadzone =

Hi all, as good? I am trying to go up a board TE110P with link E1 ISDN PRI to establish connection with a central office Siemens HiPath 4000. But I am having the following errors: Server1:~ # asterisk -r Asterisk 1.2.10, Copyright (C) 1999 - 2006 Digium, Inc. and others. Created by Mark Spencer <markster@digium.com> Asterisk comes with ABSOLUTELY NO WARRANTY; type 'show warranty'

Hi, For a significant time now (since about 0.2.0-rc8n) the qozap driver has become very verbose if an ISDN line is not connected... I get the messages below every couple of seconds in the asterisk logs. The "flaw" in the messages is the "Alarm cleared" message - The alarm cannot possibly be cleared because there is no physical media connected into that port!!! (BTW - All

Hi there I have a TE110P card fitted in my linux box running : Linux version 2.6.9-5.ELsmp (bhcompile@decompose.build.redhat.com) (gcc version 3.4.3 20041212 (Red Hat 3.4.3-9.EL4)) #1 SMP Wed Jan 5 19:30:39 EST 2005 I followed the installation steps on digium website...no errors reported. The modules seem to have loaded...here's what lsmod shows: Module Size Used by

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Good day eveyone, I'm hoping that someone can help me. Perhapps i'm overlooking the obvious, in truth, I hope that I am. I've scoured the mailing list and google, and haven't come up with much. I have a Digium T400P thats been connected to a channel bank for testing for some time now. all has been well. I've now just had

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi. I'm getting the following error at random intervals on my TE410P with Asterisk CVS-03/30/04-11:49:01-CEST. I have two spans active, one connected to my Telco, the other to a Siemens PABX. Both spans display this behavior at random intervals. All calls are dropped when this happens. Spans are not necessarily in use when this happens.