similar to: CID on Polycom Phones

I hope this doesn't already exist, but I couldn't find anything to help. I am installing a brand new Asterisk server, and want to use the Polycom IP331 phones. Does anyone have any steps on how to configure these? I have softphones working just fine, but for some reason I can't find a clear step by step on provisioning the Polycoms. Any help is greatly appreciated! Mark J.

All, I have a Polycom 650 phone, when turned on displays "Checking application". Can any give me some information as to what is wrong? I have copied the CFG files from a 601 phone to work with this 650. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070429/daadda2a/attachment.htm

Hi All, I have a Polycom Handset on a front door and I'd like the phone to dial a number as soon as the handset is lifted without having to press and buttons or enter any numbers. I know how to do this on a Linksys but I can't find out how to do it on a Polycom. I would be greatly appreciate is some is able to tell me how this is accomplished. Regards David. -------------- next part

Hi All, I have installed a number of Digium G100 devices in many countries like South Korea, Japan, Singapore and Australia. I have just installed two in New Zealand and both sites are having a problem with Caller ID. Incoming calls are dropping the first digit 0 from the caller ID. I was previously using DAHDI and a TE121 device which may have been adding the 0, I'm not too sure about

Hi All, I'm having problems trying to get a TE120P operational in Canada. I keep getting a congestion error when I try to make a call. I'm not sure if my switching, parity, etc is correct. I'm hoping that someone will be able to verify my config. The Telco is SaskTel, with a 10 channel 50 DDI service. Zap show channels show and ztcfg -vv looks ok and the zttool show

All, I'm hoping someone can direct me as to why when someone calls my DID Asterisk tries to authenticate the incoming call on my outbound context. If I remove the GoTalk context I can receive incoming calls. Outbound calls work fine while I have the GoTalk context in place. The error I am getting when someone calls the DID is WARNING[16072]: chan_sip.c:8272 check_auth: username mismatch,

Hi All, I have installed Asterisk 1.4.2 and have loaded ztdummy as I have no Digium cards. The problem I have is that MOH will not play. It starts and then stops. asterisk*CLI> zap show status Description Alarms IRQ bpviol CRC4 ZTDUMMY/1 1 UNCONFIGUR 0 0 0 I'm not sure if the above is correct.

Is it possible to display the incoming calling number on a handset when trying to pick up a call from another handset? I currently have Call Pickup working using *8, I have also used the PickUp application successfully but I'm not sure how to use these features so the handsets show the incoming calling number and not the number that you have dialled to pick up the call. Regards David

Hello List, This is what I want to do: When a call comes in I want to ring an extension that happens to be loud speaker. The users can the press *8 to answer the call. Is there a SIP device that I can connect to Asterisk as an extension that can accomplish something like this? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All, This may be an off topic but I'm not sure who else would know the answer. I'm playing around with Asterisk and Polycom phones. I see Polycom supports quite a few codec. The usual ones and these: G722 Siren14.24kbps Siren22.32kbps Siren14.32kbps Siren22.48kbps Siren14.48kbps Siren22.64kbps G7221.16kbps

Hi All, I have a Polycom 501 that is behind a NAT. When it registers to the Asterisk server it is using the IP address on the private network and not the public IP of the NAT address. Can someone tell me what I need to do so the phone registerers using an internet address rather than the remote network NAT address. -------------- next part -------------- An HTML attachment was

Hi All, I can not install the asterisk-addons as it thinks there is no mysqlclient installed. I have installed mysql, mysql-server and mysql-devel and I am still unable to install the addons. I am running CentOS 5.2 i386. Please somebody help. -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm not sure if I have a configuration problem or not. I am unable to dial out. When I try to dial in I can hear the phone ring on the dialling phone but Asterisk does not register anything. In zaptel.conf I have loadzone = au defaultzone=au fxsks=1 In zapata.conf language=au context=from-pstn When I do: zap show channels I get: Chan Extension Context Language

Can someone please help me with a problem that I seem to have with this Polycom 601 phone. It will not see my TFTP server and keeps saying "Could not contact boot server, using existing configuration". I have Linksys phones that use the TFTP server without any problems but this Polycom will not see or use it. Please Help. -------------- next part -------------- An HTML attachment

The Telco in Canada is been real painful. I was wondering if anyone has installed a Digium TE1X0P card in Canada and if their Telco was so difficult. The Telco will not provide us a service until they see a FCC or DOC number for the equipment ware are connecting to their service. If have found "FCC Part 68, ANSI/ITA-968-A, Including Amendment A1 and A2 Industry Canada CS-03"

Hi All, I have installed newt and newt_devel but dahdi_tool will not compile/install. I'm trying this with dahdi-linux-complete-2.5.0.2+2.5.0.2. does anyone have any suggestions as to what I am doing wrong? Regards David. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, we use Polycom SP IP 501 phones. We use the standard key/softkey configuration to do attended transfers. The only thing we miss is the CID info of the original caller after the call is transfered. This behaviour is different from the blind/direct transfer. With blind transfer method the original CID info is displayed. We already opened a call (in 2006) with Polycom JIRA. This is what they

I have a brand new TE120P card that I have installed and asterisk is not starting as I am getting the error: ERROR[5054] chan_zap.c: Unknown signalling method 'pri_cpe' It seems it does not matter what I change the vaule for signalling= to, it always returns it as invalid. I have tried the config from my other 2 servers running TE110P cards and the config from AusTechPartniships

Hi guys, I currently have about 10 Asterisk servers scattered around the place each hosting their own dynamic conference centre. Is there any way that when people join these conference centres on each server that somehow Asterisk bridges the conference centres on each server to form one large conference? Many Thanks David. -------------- next part -------------- An HTML attachment was

Hi All, I'm stuck and need some help. I have installed the Asterisk CDR Analyser Version 2.0.1. It mostly works except for the CDR Report. I get the following error even though it lists the CDR details. Database error: Invalid SQL: SELECT substring(calldate,1,10) AS day, sum(duration) AS calltime, count(*) as nbcall FROM cdr WHERE UNIX_TIMESTAMP(calldate) >=