similar to: zaptel 1.2.18 and HPEC

Hi all, Just want to check from the list experienced personal about the Digium HPEC, where I had purchased the HPEC and wish to run with TDM card Sangoma A200. I can't install HPEC to run with Sangama A200 card, even I had changed my hpec file from i686 to i386. The error that I had as bellow; > Found key 'HPEC-XXXXXXXXXX' for 2 channels. > Found valid HPEC licenses for 2

I have a _very_ specific situation where I need queues to work in a very specific manner - I need the queue to only accept one call at a time, even though several phones are attached to it. My memory tells me that queues might have even worked this way in the distant past (pre 1.0)...but I am willing to be mistaken. Is this even remotely possible? PaulH

Hi All - I've been trying to compile Zaptel w/ HPEC, but I've been unsuccessful. The system is CentOS 4.4, zaptel version 1.2.15. I believe I've got all the requisite files, and they're in the right locations in the zaptel tree. When I compile, I get the following warning from make: Warning: could not find /usr/src/zaptel-1.2.15/hpec/.hpec_x86_32.o.cmd for

I recently read about the following new technologies from Digium. Has anyone tried the new HPEC or knows when it will be available? TDM800P and HPEC The TDM800P is an 8-port analog telephony interface card, so it fills the gap between Digium's 4-port and 24-port cards. Analog phones and POTS lines are going to be with us for some time, and demand for support for them remains high. The

Hi - I had a client recently move their asterisk system (asterisk 1.4.26, dahdi 2.2.0.1, aex800 w/vpm module) to a "new" location, a building that's nearly 150 years old. I was not personally able to go there, but the person who did the move said the building's demarc room was "scary"-- water leaks, jumbled and frayed wiring, and all sorts of other fun. The echo on

I am running 64 bit linux on my Asterisk box and would like to get the new HPEC software running on it. However, while there are 32 bit modules available, there are no 64 bit modules on the ftp site: http://ftp.digium.com/pub/telephony/hpec/64-bit/ In some places on the digium website it states 32 bit only and other places including the documentation it states 32 & 64 bit are available.

I was previously using an old computer running Asterisk 1.2 with zaptel. Once the CPU fried I switch to a new computer and I chose AsteriskNow 1.5 running in 64bits to simplify the installation process. I manage to find my way with configuring dahdi instead of zaptel and to switch all my previous config to the new computer. Now everything is fine except that even if I use the md2 echo

Hello, Has anyone tried the combination of asterisk 1.2.24, zaptel 1.4.5 and HPEC 9.00.003? In particular, with a hardware configuration similar to: Module 0: Installed -- AUTO FXO (FCC mode) Module 1: Installed -- AUTO FXO (FCC mode) Module 2: Installed -- AUTO FXO (FCC mode) Module 3: Not installed Found a Wildcard TDM: Wildcard TDM400P REV I (3 modules) I have two fully independent systems

Just wondering how your experience is with HPEC, Is it just for analog interfaces or we can use it on TE122 as well? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080214/3f0580f1/attachment.htm

I have recently moved an asterisk system to a new location. This location is experiencing terrible echo. I installed the HPEC from Digium but that has caused a new problem. When HPEC is enabled and more that 16 taps are used, the audio from the outside caller gets clipped. Instead of hearing: Hello, my name is Mike one hears He o, m ame ike If the taps are set to less than 16, there

thankyou both very much for your swift responses and helpful insight... While my knowledge of administrating Asterisk is fairly decent, i must say my knowledgebase and ability in troubleshooting it is fairly lousy... all these wonderful suggestions you have had about turning this log on here, etc sounds great, but i don't know where to begin on that! how do you recommend i turn these on or

Is there a way to specify multiple email addresses in voicemail.conf for a specific user? I seem to remember that it was possible, but can't remember the character to separate the email addresses. (I tried '&', but that didn't work...) later, PaulH

I am trying to send 'codes' over an isdn2 link - such as *#24# - to activate call forwarding. But it doesn't work. I have tried sending it as a straight dial, and also as a DTMF string...but no luck... I spoke to a telco tech and he said I had to send a facility code....huh? Anyone with any ideas on this one? PaulH

Hello, Are HPEC (ie zaptel 1.2.X) and bristuff compatible ? And the results ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070413/b5adde2a/attachment.htm

I need to carry a variable over into the 'h' priority - so I can go back and clean up DB entries in a mysql database (time of call and so on) I tried using UNIQUEID but it seems that 'h' generates a new one. Anyone have any ideas? What can I use to carry a variable over into 'h'?? later, PaulH

Any idea how to read an external file, grab some stuff and push it back into an Asterisk variable? I can do it the other way with: system(echo "${UNIQUEID} =>" >> /home/ast/curr_calls) but I'm a bit stumped on how to go the other way around.... much thanks, Paul Hales

Hi, I explain what I want to do.. All the operators share their phones. The number of the operator isn't constant, so it's possible that two operators share all the phones. They need to move all around, so they pick up the first phone they find. If there are only few operator is very annoying for them to ear the other phones ringing while they are at the phone! So I'dd like to limit

Does anyone know of any startups using Asterisk? What about established companies? Ones that are hiring would be nice.... :) Doug.

Hi, everyone: I am developing a system using Asterisk, TDM-400 analog cards, analog lines, and Polycom SIP phones for internal extensions. Initially there was bad echo but after a series of efforts, I've managed to reduce it to a negligible level (it only happens when both parties speak simultaneously, and even there, only for a few hundred milliseconds). From an echo standpoint, things are

Hi I've bought the Digium g729 codec and have installed it correctly (I think) >> voip*CLI> show g729 >> 0/0 encoders/decoders of 3 licensed channels are currently in use if I do an echo test either from a sip Cisco 7960 or another hard phone (unbranded) using g729 it sometimes works and sometimes the announcement about the test (echo-test.gsm) fails part way though but the