similar to: Unicall + MFC/R2 line dropped immediately after connect

Hi All, I have an R2 installation still undergoing testings, during the test I notice that the Unicall always respond B6 to a II-1 (from a forward switch). Except, for a DNIS that can't be found in the dial plan, in this case it respond with B5. My real problem is, the call will be terminate on a Cisco 7206 with ISDN/PRI thru SIP. If the Called number is busy or the Cisco 7206 is busy or

Hi, I have three R2 installation on different carriers, all shows the same inconsistency at varying degree. But, on most test calls we made, it reaches T3. The worst part of these, the carrier claims that it's my R2 box that is not responding in time. Please, check the attached file and take note of the timestamp, you'll find that in some call, it already contradict what the carrier

Hi All, as good? I am trying to make a call for the Unicall channels and after the exchange of signalling and sending of the digits asterisk locks up with the sending of the signalling "E" and the TELCO says that asterisk would have to send signalling "F", as to make for asterisk to send signalling "F"? The TELCO says that the signalling "E" is

Hello All, I'm facing problems with Unicall on this scenario : CentOS 4.3 - Running on x86_64 Asterisk 1.2.7.1 Zaptel 1.2.5 When running zttool , shows all Spans OK. But I can't receive and make calls. I tried to change many parameters and still doesn't work. Any clues ? * unicall.conf [channels] language=br context=incoming-pstn usecallerid=yes hidecallerid=no immediate=no

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi, i have one Asterisk with a Digium E1 card, and a Meridian Nortel Release 11. I need to connect both of them. We are using MFC/R2 for this.. The Diagram: [ NORTEL ] ( AMI ) ------------------------------------------------ (DIGIUM) [ ASTERISK] we have green light at the digium card, and at asterisk we see all 31 channels as idle. But when i want to recive a call from the Nortel to the

Hi all, I have Asterisk 1.2.10, zaptel 1.2.7, spandsp-0.0.3pre22 compiled, and a Sangoma A101, and when I make a call I get this: Jan 8 13:04:06 DEBUG[12252]: chan_unicall.c:2000 unicall_exception: Exception on 19, channel 1 Jan 8 13:04:06 WARNING[12252]: chan_unicall.c:627 unicall_report: MFC/R2 UniCall/1 <- 1101 [1/ 40/Seize /Idle ] Jan 8 13:04:06 WARNING[12252]:

Hello! I'm tryuing to bring up an R2 connection but eventhough I've followed the guidelines in: http://zarzamora.com.mx/asterisk/17 something seems to be missing. When an incomming call is generated I get: Nov 24 06:01:17 WARNING[-197416016]: chan_unicall.c:612 unicall_report: MFC/R2 UniCall/24 <- 0001 [1/ 1/Idle /Idle ] Nov 24 06:01:17 WARNING[-197416016]:

Hi all I have MFCR2 successfully installed but seems to get warnings a s seen below when I start asterisk. Am running on Redhat 9. Asterisk Ready. *CLI> Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 far_unblocking_expired Dec 20 08:40:38 WARNING[1175077440]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 local_unblocking_expired Dec 20 08:40:38

Hello guys! I hope you bare with yet another newbie on the list! :-) I am trying to setup an asterisk installation in between a Siemens HiPath 3800 and my local carrier (Telefonica/Brazil). Both running R2. ISDN is not an option on the carrier. :-( I could apparently setup both E1s just fine according to zttool (both OK with no alarms) but, and this is where it starts to get

Hello all, as good? I am trying to use the package astunicall-1.2.21.0.1 with a Sangoma A104D card and 04 links E1 mfc/r2 in Brazil. The compilation occurred, normally and links is UP if I place in Loop and I obtain to effect called in Loop, but when I extend for the PSTN, links reports the following messages, without asterisk start calls: Dec 5 22:27:12 WARNING[3868]: chan_unicall.c:627

Hi all, any body can tell me why i am receiving this message in my sever ? I have running * with 10 Digital Lines, but i am receiving a lot of times this message . Is a software issue or is a hardware issue ? Regards. Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:2672 handle_uc_event: Unicall/5 event Alarm Mar 27 12:58:24 WARNING[2586]: chan_unicall.c:3091 handle_uc_event: Unicall/5 Alarm masks

Hi, I'm running Asterisk 1.4.2 on a Debian GNU/Linux and a Digium TE210P card. I have one E1 with MFCR2 Signaling. I compiled asterisk + libunicall, and I can make calls over E1, but can't receive. Here the CLI when I make a call: -- Executing [006191642208@ps5:1] Dial("SIP/23-081cbc40", "Unicall/g1/91642208|50") in new stack -- Called g1/91642208 [May 14

Hi all, I still haven't seen my first post (cry for help) so I'm not sure if these are going through or not ... I've played with the box all day today ... I got it to quit seg faulting finally by playing with the config files. Currently I have 4 spans configured for a Digium TE420B (With Octastic DSP) Here is my zaptel.conf: (I know the device connected to spans 1-3 are providing

Hi! Im having some troubles trying to configure * as a bridge between a telco and a pbx with R2, the scenario is this: ------------ E1/R2 --------- E1/R2 ------------ | Telco |-------------| * |-------------| PBX | | (Telmex) | --------- | | ------------ ------------ I can receive calls from the telco

Dear Steve and *.* e1r2 developers and users, now MFCR2 is successfully installed! many thanks for your help. I'm living in Argelia. I have configure my MFCR2 according argentina R2 settigs. (look at the end of the message) the testcall run perfectly (only warnings and I think that is just debug). but I have many problems and when I run Asterisk-MFCR2, generally in the begging no errors

If I make a call to asterisk's r2 E1 I get these errors *CLI> Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Rx bits 0x1 [1/ 1/ 0/ 0] Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Detected Jan 10 16:16:38 WARNING[1089170112]: chan_unicall.c:634 unicall_error: UniCall: mfcr2 Making a new call with CRN

I am having a strange problem with an asterisk servier using R2 Unicall in Mexico. Most calls go through fine but some of them give me an error like this: -- Executing Dial("SIP/86-db41", "Unicall/g2/014448343600") in new stack -- Called g2/014448343600 Feb 9 21:44:39 WARNING[23069]: chan_unicall.c:2644 handle_uc_event: Unicall/2 event Dialing Feb 9 21:44:45

I've been trying to configure an E1 in Mexico using unicall, i went into vozdigital, googled this list, and finally followed this instructions: http://voip-info.org/tiki-index.php?page=Asterisk+MFC+R2 I have 10 PSTN numbers and 10 "lines" assigned, so i only have 10 "channels" assigned from my telco. However when i try to simulate a call using this call file: --------call

Hi everybody We are having periodically troubles with the outbounds calls, seem like the PBX cannot end to dial the entire string of numbers This is output from the PBX., few minutes after all work fine again ... :(, and few minutes after the same problem appears. Thanks in advanced ... Regards This is the PBX aout and my zaptel, zapata confs. Runing asterisk 1.0.9 libmfcr2-0.0.2