similar to: Adtran feature codes, extensions

Has anybody had any luck getting an Adtran Total Access 616 working via the Ethernet port/MGCP to an * box? The voice lines don't seem to be coming up and I wasn't sure if I had something missing. Here's my mgcp.conf file: [general] port = 2427 bindaddr = 0.0.0.0 [10.189.189.31] context=nicktest host=10.189.189.31 canreinvite=no line => aaln/1 line => aaln/2

I've never set up an mgcp device before. I have an Adtran IAD with the MGCP firmware on it. I have it configured in mgcp.conf like this: [general] port = 2427 bindaddr = 0.0.0.0 [adtran] host = 192.168.2.2 context = default canreinvite = no line => aaln/1 line => aaln/2 The device is configured like this: MGCP Configuration | Standard MGCP 0.1 / NCS 1.0 MGCP Endpoint

I have a TDM400P (configured with 4 FXO cards) in a box that was working fine from POTS lines extracted from a Lightspan via DSC's channel bank, but when I switched over to using an Adtran 616 (weird little box, takes an SHDSL circuit in that splits out 16 analog lines via an amp connector) the card no longer seems to be able to detect ringing. I've tried upping the rxgain with no

I thought this might interest a few asterisk users. I don't use them so I have no idea about Adtran's but I know a heap of people on this list swear by them. Cheers, Dean ________________________________ From: vclass.coordinator@adtran.com [mailto:vclass.coordinator_adtran.com@mail.vresp.com] Sent: Monday, 19 September 2005 9:59 AM Subject: ADTRAN Virtual Classes: Ensuring

Rich, Thanks a bunch, totally understand now and that actually makes total sense. (no need for schematics). This also explains why I used an TA750 to go into a Nortel MICS system, using FXO and no buzz. Totally balanced load from the analog ports on the Nortel across the 5 feet of CAT5 to the FXO on the adtran. Now I need to get rid of some Adtrans --- Anyone lookin to buy? :) Thanks

Hello, I have just received Adtran TSU 600 with 24 FXS ports. I have installed sucessfuly T100P card. Adtran is connected to t100p with crossover T1 cable. On T100P card I have a green light and on Adtran I do not get any errors or alarms. But I do not get dialtone on FXS ports. Adtran is configured: For Network Timing, fxs ports ore fxs_ls on Adtran. In zaptel.conf: span=1,1,0,esf,b8zs

I believe it is not fiber, but I am not sure. I am going to take one of them home tonight and hook it to my POTS line there, which for sure is not fiber. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Michael Welter Sent:

I am sending a call down a E&M wink trunk to a adtran tsu600 channelbank. The extension is setup like so... exten=>799179,1,Dial(zap/g2,20,D(9179)) exten=>799179,2,Hangup() It should Dial the Adtran and send some DTMF signals to a telephone on an fxs module in the Adtran. Asterisk is seeing the call answered when the T-1 is picked up by the Adtran not when the ringing phone is answered.

I have following setup Asterisk - T100P -> Adtran TSU600 P + FXOcard -> PSTN line When PSTN line is plugged directly in to analog X100P caller id is received by Asterisk but when I plug it into adtran I'm not getting caller id. Any ideas what kind of setup Adtran TSU600 requires to pass caller id to T100P ??? regards m.

I just wanted to ask about using Adtran boxes to support analog lines into an Asterisk box. Right now x101p's are just too sensitive to RF noise inside the PC. Going with an external chassis looks like a good, albeit expensive option. It looks like I can use the Digium T1 card into an Adtran 850. The Adtran 850 would need FXO cards. It would also need the echo cancellation module. Is

Hello Can somebody send me please config files of zaptel.conf and zapata.conf for adtran fxs ports. I cannot make it work. I do not get a dial tone on Adtran and when I am trying to call from sip i get: app_dial.c:674 dial_exec: Unable to create channel of type 'Zap' == Everyone is busy at this time There are no errors on T100P and adtran. Please help! B.

All, I need help. I have an (actually 2) Adtran TA750's with 8 FXO ports. I get a terrible buzz on every FXO port. If I unplug the Adtran and put an analog phone on each incoming line, I have no buzz. I also have 2 Carrier Access Access Bank I's with 12 FXO ports. When I plug the same analog lines into either one of those, no noise or buzz whatsoever. I went so far as to move the TA750

Jay, I have had a lot of trouble with the FXO ports on Adtran TA750. Unless the incoming POTS lines have a balance impedance, they will buzz very bad. Gregory P. Scasny Golden Technologies Inc. http://www.golden-tech.com 219-462-7200 -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Sunday, April

I have a T100P card connected to an Adtran and then a T1. I have added the following configurations to Asterisk...but, when I dial 9 and then a local phone number, it bounces between the dial tone and silence and the *error* light on the Adtran blinks. zaptel.conf span=1,0,0,esf,b8zs fxsks=1-8 loadzone=us defaultzone=us zapata.conf [channels] context=from-sip signalling=fxs_ks

I am having a problem using the Adtran 750 FXO quad card with a Groundstart trunk line. I am able to receive calls on the trunk line, however dialing out is not working. The Adtran does not seem to be doing the signaling. Has anyone used the 750 FXO card in Groundstart mode? Any special configuration issues that I should be aware of? Syed Akbar Alico Systems Inc www.alicosystems.com Tel:

Can I configure an Adtran channel bank with a mixture of FXS and FXO cards and have them come into a single T100P T1 card? It seems like this would be a cheaper solution than trying to load a bunch of PCI cards into a PC. Also, when shopping for an Adtran (on ebay) - what do I need to watch out for as far as interfaces or capabilities to make sure that it works with a Digium card?

People on the list tend to think you can't make many cards work on a regular desktop. If you're willing to wait a couple of week I might have an answer for you. _____ From: Robert Augustyn [mailto:augustynr@yahoo.com] Sent: Saturday, December 11, 2004 7:13 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Will Adtran TSU 600 work with *?

I have three quad FXS cards (in slots 1-3) and one quad FXO card in slot 4. I have a few telephone sets connected to the FXS cards, and * allows calling from one phone to another and from phone to console, etc. Diax also works. I have a CO line connected to one circuit of the the FXO card. When I dial from the console, the busy light on the FXO card comes on, but it doesn't break dial

Good Day list, I have googled and wiki'd myself to no avail. Here is my setup. Asterisk Box Digium T1 card connected to an adtran Total Access 624. I need to pass ANI and DNIS information from asterisk to the analog devices hanging off the adtran. The digits are announced to the fxs devices between ring 1 and ring 2 (If I pick up the anlog phone after ring 1, I can hear them so I

I have a system that I am trying to get a port on a Sangoma A104d card connected to an Adtran 850 with 5 FXS modules and 1 FXO module. A problem I am having is figuring out what cable should be used from the port on the Sangoma to the JP2 port on the Adtran. Tried was a cross-over T1 (1->4, 2->5, 4->1, 5->2) as well as a straight T1 (1->1, 2->2, 4->4, 5->5). Neither one