similar to: Testing ISDN T1/E1 Bri and Pri etc.

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

hi all we want to use Two single port Bri cards in Trixbox. Any idea which card is having good support and performance repotation especially when using two or more in Trixbox. Regards farooq --

Hi, I am thinking of starting a project at Work to pilot to use of Astrisk and VOIP, and would like to tie in several projects together. Currently we are looking at purchasing an ISDN and H.323 based video conferencing system from Polycom. It suggests the use of 3-4 BRI lines (ie 6-8 B channels, but in the form of individual BRIs). We need ISDN for the video conferencing to communicate with

Hi, I'm looking for a mean to send digital data over an E1 line, just like isdn4linux or Capi via AVM's FritzCard is able to do it with BRI lines (e.g. for PPP or ISDN raw connections). I'm not looking for modulated audio data representing digital data, like fax or the analogue modems of former times. I want an interface to the ISDN raw data, with an outgoing call marked as

Hi, Anybody have lots of experience with PCI ISDN cards and Asterisk? I'm thinking of getting a BRI in my house to deliver more advanced signaling to my PBX (yes, I'm a geek :-)) but I've never played with isdn4linux. Is there any particular BRI card that works better with Asterisk than any other? Also, can the BRI interface cards participate in conference, etc., since they

Hi all, For a while now I've been using Asterisk together with HFC-PCI cards (Cologne chipset) for Euro-ISDN BRI support. However, I do not consider this to be the most reliable solution and believe that the most stubborn problems have always been software related. If my clients are willing to spend a bit more money on different hardware, what do you think the best solution would be?

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

Howdy: Does echo only occur on analogue PSTN lines, or can it also occur on PRI and BRI lines? If so, for the same reasons? This is a part of our consideration to transition to BRI. Sincerely, Brent A. Torrenga brent.torrenga@torrenga.com Torrenga Engineering, Inc. 907 Ridge Road Munster, Indiana 46321-1771 219.836.8918x325 Voice 219.836.1138 Facsimile www.torrenga.com

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Having ISDN FXOs and a bunch of ISDN DECT base stations, I went looking for a CAPI compatible active BRI adapter capable of NT mode. I have found that the 'Eicon Diva Server 4BRI' fulfills theses requirements. However, at EUR 1387 for four BRI interfaces, it does not come cheap. Are there other users of similar hardware that can point me to alternatives ?

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello everyone. I need a BRI ISDN card that works in Romania. I already have one of the "Cologne HFC-S" PCI cards and it doesn't work right, it's junk. I get waaaay too much echo using it. I'm now "shopping" for a better card. Can anyone recommend me a card that "fits" the following: (a) Costs less then $1000 / 750 euro (b) Has one or (preferably) two

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

Hi, As you may know, these ISDN BRI features are very important here in Europe as ISDN Basic Rate Access is very popular among Small & Medium Entreprises. I don't really know why but it seems that in many countries, default is to install small PBX using Point-to-Multipoint (PtMP) mode as opposed to Point-to-Point (PtP) which is the norm for PRI. So basically, in several countries, SME

Hi, G.722 is heavily used by Broadcasters worldwide for wideband voice communications over ISDN. I'd like to be able to receive these G.722 over ISDN calls into an Asterisk exchange (with mostly a view to routing the calls to a Voicemail box where material can be recorded). I have been examining source code for the 3 different ISDN Channels in Asterisk and they all seem to be hard- codec

Hi List, I have stupid question but I want to know it. Why we use the PRI insted of BRI ? Just for the sake of number of lines or any thing else ? And why SIP is used for making calls rather then IAX? Even we know IAX takes 1 channel for making calls? ----- Thanks and regards Virendra Bhati +91-9172341457 Asterisk Reader -------------- next part -------------- An HTML attachment was

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Dear all, I'm planning to buying Eicon Diva Server V-BRI for my asterisk server and run with chan_capi. Is anybody using that card ? Would appreciate any feedback. Bartosz

I'm trying to use a Teles (netjet) ISDN BRI card with asterisk 1.2.9.1 Anyone was able to use this card with asterisk? I couldn't find much information about it. Any help?

> Thank you all for valuable input, > > another question: when do I actually need the echo cancellation > (hardware / on board /on module ) ? > It depends on your environment. If there are still analog devices in addition to VoIP, I'd say always, but Asterisk has a rudimentary echo canceller already on board. The Telcos use echo cancellers themselves, but it cannot hurt to