similar to: TE412P (T1/E1+DSP) digium card cause server crash

Hello, I'm trying to set the 3rd span of a new digium quad card as a E&M T1 for Faxes to a Hylafax server. The 1st and 2nd spans are working as PRIs. When I start asterisk, the logs show a signaling error and chan_zap.c dies. I also get an error that it can't read the gains but they are the standard shown below. 2.6 kernel, Debian Stable, * 1.2 svn from feb 2007 my procedure: make

Hi all, I've got a fairly simple setup, a 4 port zaptel T1 card with 1 PRI and 2 flat e&m T1's coming into it, and its working perfectly except for one small thing. When people dial any of the numbers on either the PRI or the T1 from outside of the pbx, they dont get the "ringing" sound. It just directly connects the call. I know this isnt much, but its started to

I am trying to make an in/out trunk group comprised of 4 DS0's using E&M Wink signalling. The first four channels of a DS1 on a T100P are being used for the group. Outbound calls work fine, but inbound calls fail. The other 20 DS0 channels are used for a PRI. Does the configuration shown below look okay? I've tried setting 'immediate => yes' without success, but it

I have a Toshiba DK424 connected via T1 E&M to a TE110P card. Intermittently when a user dials a number I am getting 'getdtmf' errors on the Ast server and the calls do not go through. If they dial the number once or twice more, it works fine and I receive no DTMF problems. On another note, end users are complaining about intermittent disconnects. T1 is ESF/B8ZS - 24 chan. Other

I have been getting quite a bit of PRI Resets using my Quad PRI Digium card. Prior to the resets I am getting similar notices to the following chan_zap.c:7482 pri_dchannel: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 3 Telco claims the PRI's are fine on their end and that it is my unit. Is this timing? (google somewhat leads to this) I am running 1.08 asterisk zaptel

Hi, I have a client that has a 24 channel voice T1 that I have been using e&m signalling over for a number of years. The local telco finally got an ISDN switch and wants to move them to PRI. I didn't see this as a big problem - I've done a few others on this particular Caribbean island without issues, but this would be the first time with a Xorcom unit involved. We tried to do

After speaking with several people, and even participating in a forum of several other people with echo issues, I thought I'd share what we've done (well actually what our chief R&D engineer, Brett Bourn has done...) First let me say that normal cheapy PC hardware couldn't be made to function with out echo. We tried on both the single port Digium T1 card and the 4 port Digium T1

Hello all. I just received a TE110P and am trying to hook it to my Mitel 200SX has anyone successfully done this? My configuration is as follows. Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card. All I get is a blinking yellow on my TE110P card and an alarm on my Mitel. T1 card. Any advice would be great. Zaptel.conf span=1,0,1,d4,ami e&m=1-23 dchan=24

I just had the same exact problem this morning. The only thing I've done in the last couple of days is update update zaptel. I rolled back my zaptel to 2/11/04 from 3/8/04. And kept my libpri from 3/8/04. I never had this error before updated. I had other issues, but not this one. -sb -----Original Message----- From: asterisk-users-admin@lists.digium.com

I am trying to receive both CID and DNIS from the telco through a non-pri T1. Currently I have the T1 setup and operational both outbound and inbound calls are completed as should be expected. The calls came in and were placed in the context specified in zapata.conf on exten => s,1. I have requested that the telco provide callerid (they call it ANI) along with 10 digit dnis for my 800

We have install a DS3 with 28 DS1's we have an Adtran MUX breaking out the DS1's, we are trying to setup the system with 2 dchannels for each 4 DS1's. Everything looks fine when modprobe zaptel and wct4xxp and ztcfg -vvvvvv but when I asterisk asterisk it says: Aug 10 16:33:32 ERROR[8954]: chan_zap.c:6750 mkintf: Channel 24 is reserved for D-channel. Aug 10 16:33:32 ERROR[8954]:

Hi again, I'm trying to setup our non pri T1 (they call it a Long Distance T1), our current pbx has the signaling set to E&M, I can set em in zapata.conf, but I'm trying to track down the proper entries for the zaptel.conf file. The digium docs only show a PRI example. Our current system has these settings: Signalling: E&M Framing mode: ESF Line Coding: B8SZ here's my

Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5

Hi List, I need to change my provider, at this time Asterisk box is on VOIP trunk. I have two options, T1 or 15 analog lines. I have some experience with analog and I have had two main issues with it. first is echo (I have not tried HPEC yet) and second unpredictable volume. The question is, if I use TE100 with PRI , will I have same issues? I would appreciate any comments and sample zaptel.conf

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

I have a bit of a weird problem that I'm having great trouble debugging. I have a TDM400P PCI card with two FXO and two FXS modules. Both FXO modules are connected to BT lines here in the UK. Both BT lines have V23 Caller-ID, which works fine with Asterisk. Both asterisk and zaptel are fresh from CVS. Both FXO modules (channels 3 and 4) are in "group 1" for outgoing calls. My

Hi All, I have installed a Digium TE110P card on an Asterisk 1.2.1 system. Its connected directly to the PSTN. But I am unable to make outbound calls on the zap channels. The light on the card is green. Asterisk CLI shows all 24 channels when I give the command 'zap show channels'. I also noticed that Asterisk CLI shows an incoming call every few seconds on the 24th channel. This must be

<Correction in my zapata.conf file I used> Hey Everyone, So this is a problem I've been having for sometime now. I sent a few messages to the list with no luck. The problem is that when people dial into the Asterisk system using DID numbers, it works the first time or 2, then I get busy signals. A friend recommended I clear out the zapata and zaptel, start over, and recreate my

I know this topic has been covered before - I just want to make sure I am understanding this correctly. | ------------------- | | | | T1 | Channel Bank | | ----------| | | | T1 Cross | | | | | | | | ------------------- -------------- | Asterisk | | | |

Hello, I have a T1 (not PRI) plugged into my Asterisk server. Everything is working well, except I only get the first digit of the 4 digit DID in Asterisk. The T1 provider (Eschelon) tried switching to 7 digits, and I only got the first digit of the 7. Can anybody help? We're adding another DID and I need to trap it correctly. Thanks. Here are snippets from the relevant files: --