similar to: New to Asterisk

All, I have a machine with a TDM04B and a TDM13B card in it. For over a week it was working find placing a call out every 10 minutes to the intercom system. Today that stopped working. The call was still getting placed just as it was in the outgoing spool and "looked" like everyting was working just no audio on the intercom. I picked up the analog phone on the TDM13B (the one port that

Hi, We are recieving some faxes, but I would say that about 50% of them do not work. We don't know why... is it something with the faxes speed, volume, etc? Should we use a real fax machine? Using a TDM13B with a rxgain of about 5.0... Thank you for any help. -- Alexandre Leclerc

Hi All; If one of my FXS port damaged at TDM22B because we connected the Telephone Line cable to the FXS port while it should be connected to the FXO port, then can I order S110M FXS Module and fix it instead of the damaged FXS? (This if we assume my problem that really the FXS port damaged). Rregards Bilal

This is rather bizarre: My TDM11 (one FXS) rings a $10 passive phone with REN of 1.0B, a cheap speaker phone of 0.3B, and a cordless phone with marked REN of 0.0B. But it couldn't properly ring this 27935GE3-B (FCC ID G9H2-7930) cordless phone rated at merely 0.1B. Rarely, the phone will crack out an occasional weak and abrupt beap, but never a normal ring. Otherwise Asterisk and TDM400P

I have seen this in the archives any number of times -- but I have yet to find a solution that works for me. Any suggestions you can offer would be most appreciated. Here are the answers to the questions I have seen asked in earlier posts. The log contains: Mar 10 12:26:29 WARNING[3015] chan_zap.c: Unable to specify channel 4: No such device Mar 10 12:26:29 ERROR[3015] chan_zap.c: Unable

I have a TDM21B (A new TDM20B that just arrived plus a X100M that I already had). This card sometimes works, and sometimes only the FXO module is seen. (correction to previous message that incorrectly listed X400M/S400M when I'm using only the single port versions of these modules (X100M/S110M). By "works", I mean all 3 modules have the green lights on the ports on and when

Hello, I have configured my TDM01B Card (1 FXO Port ) as follows (below) but it will not pick up an incoming call. Any suggestions/tools to see what the problem is? I have looked at zttool where this line changes but I don't understand what it means (The last digit changed from 0 to 1) Total/Conf/Act: 4/ 1/ 1 /etc/zaptel.conf fxsks=4 loadzone=nl defaultzone=nl

Hi, I recently installed a gentoo on a PC, purchased a TDM400 and installed asterisk. Kernel is 2.6.11-rc3 First, there seems to be a problem with my system: I must put the pci=routeirq to make the card detected. The modules are loaded ok (dmesg output) Zapata Telephony Interface Registered on major 196 ACPI: PCI interrupt 0000:00:08.0[A] -> GSI 16 (level, low) -> IRQ 16 Freshmaker

The Asterisk Development Team is pleased to announce the release of Zaptel 1.4.0-beta3. This release contains a number of updates: - compatibility with Linux kernel 2.6.19 - bug fixes to the Xorcom Astribank driver (XPP) - support for Digium's TE110P Rev C, VPMOCT064 and new revisions of the S110M and S400M FXS modules - various other bug fixes Thanks for supporting Asterisk and Zaptel!

The Asterisk Development Team is pleased to announce the release of Zaptel 1.4.0-beta3. This release contains a number of updates: - compatibility with Linux kernel 2.6.19 - bug fixes to the Xorcom Astribank driver (XPP) - support for Digium's TE110P Rev C, VPMOCT064 and new revisions of the S110M and S400M FXS modules - various other bug fixes Thanks for supporting Asterisk and Zaptel!

I'm afraid that I am at a loss here. I am new to Asterisk, and have successfully set up SIP. But I cannot get my FXS card working, and I'm not sure what else I can try. # modprobe wcfxo /lib/modules/2.4.21-37.0.1.ELsmp/misc/wcfxo.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may

I seem to have tripped over a problem that just seems plain weird to me... I have the TDM card with 1 FXS and 3 FXO interfaces. The FXS connects to a modem and EFTPOS terminal, which is working fine. The 3 FXO ports are connecting to another PBX as internal extensions. Usually, everything works fine, however, yesterday incoming calls stopped working. When an extension on the PBX calls one of

Hi all, I just got my long awaited FXS modules for a TDM400 card, and was a bit puzzled about how my phones and the FXS interface worked together. Here goes: In Sweden (that's where I am located) phones traditionally are connected in daisy chain configuration. This means that a phone in on-hook condition passes the line through back onto the outer pair of the RJ11, back into the wall

Hi All - I pulled from a working system a TDM400 with one s110 fxs and three x100 fxos. I put it into a new box and the fxs no longer works. The fxos work just fine. I thought it was odd, but I chalked it up to a random chance failure and ordered another s110. The replacement doesn't work either, and now I'm confused. dahdi_scan recognizes the s110, but it says it fails. Output

Hi, A week or so ago I wrote about the problems I was having using a Digium TDM04B card in a Dell PowerEdge 750 IU running Fedora Core 1. Digium steadfastly indicates their card won't work in any PowerEdge 650, 700 and 750 series machines "do (sic) to a failure in interrupt handling between the pci bus and the card." My question to the list is: for those of you using a TDM04B

I would like to install a TDM04B with Asterisk@Home 2.4 and Asterisk@Home 1.5 but I didn't find documentation about this installation. Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060206/85ff5252/attachment.htm

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

Hi, I recently got a TDM04B and after installing and getting asterisk up and running I connected a handset to one of the ports. Unfortunately I don't get a dial tone when I lift the handset. What could be the cause of this? Could someone point me in the direction of a proper config for a TDM04B? Thanks.

Hi, I am just trying to figure out how to setup a TDM04B card for incoming/outgoing calls. I have 4 lines, which are provided as a rotary trunk group, currently hooked into a Nortel system, which asterisk will replace. I have setup a Dell 1800 (Tower) system with the TDM04B card, which seems to work. The question is how do I set it up that all 4 lines are part of a trunk group, such that

Hello All, I got my TDM04B card installed and configured. Everything works fine I can receive calls and route to appropriate extensions. The only problem I am facing is Slowness. When I dial the PSTN number which is connected to Zap 1-1 after two ring it answers and then run the AGI script. What I did was assign it to a specific extension. So all inbound call on that PSTN number should