similar to: YAACID and manager.conf security

Hi everyone, i'm announcing YAACID: Yet Another Asterisk Caller ID V0.9 it's the first public release. we've been using it in our office for a couple of months now. YAACID is a native Windows (.NET) program that sits in the notification area and logs into the manager interface. it waits for a call to come in on a monitored channel and then pops up the callerid info in a very

Hello, I'm trying YAACID ( http://www.shatterit.com/opensource/yaacid/ ) for incomming call notification on PC (and open url with callerid), but it does not display/pop anything :-( my config is very simple... (yaacid is successfully registered as manager in asterisk) thanks PJ * dialplan: '953' => 1. NoOp(${CALLERID}) [pbx_config]

Hi everyone - I have a nicely working system to which I'd like to add popups for incoming calls. Calls go into a queue, then all extensions ring. I'd like the agent that answers to call to get the popup on screen. I'm currently using Flash Operator Panel to get a popup (other suggestions welcome). Currently, all users get a popup when the call first goes into the queue

hey all, from a lot of great feedback we found some bugs in YAACID that appear in *@home and the stable asterisk versions and older CVS versions. we're putting the fixes in and will have a new one tomorrow on the web site.. Thanks, Mark

I lost one channel on an FXO module on a Sangoma A200 card due to a lightening zap in the area (well - it died the same night as a major thunder storm came through).... Is there a recommended/standard surge protector for phone lines I should be using? My server has 2 POTS lines. thanks Todd

Hi - I've got a new install with a Sangoma A200 and a few GXP2000's. When users are talking over the Sangoma, they get a lot of sidetone (local echo). Internal calls are fine. Where do I adjust that? I assume its in zapata.conf somewhere? thanks Todd

I've got my asterisk server in the DMZ of my local LAN - I've used my Budgetone and GXP2000's from the Internet- on direct IP connections with no problems. However, I'm about to deploy about 5 phones (either budgetone or GXP2000's) all on a LAN behind a NAT- on a different network than the Asterisk server. Should I look into using STUN servers? Will this setup be a

Valued Colleagues, I am trying to configure and use asterisk manager API. The /etc/asterisk/manager.conf and the output of "netstat -nl" are appended below. When I restart asterisk, I believe I should be able to see the asterisk listening on port 5038 using netstat. But when I type netstat, I don't see any applications listening on port 5038. When I telnet to port

Hello everyone! I'm planning on setting up a new system shortly and can't pick the right card... We will have 2 or 3 lines coming in and 7 extensions (GXP2k's). Should I just get 2 or 3 X100P cards? Or do I need the Sangoma A20200 or even the A20200D (Echo cancelation)... I was thinking I'd use a Dell 2.0 GHz machine as the server... If anyone has suggestions as to

Hi - I just got a Sangoma A200 card with a single 2FXO module and what appears to be an empty module. I put the card in my Dell GX260, but the power light on the front of the box just blinks and won't power up. I did take the power cable from the CDROM to put on the card - I don't need the CDROM right now.. I'm looking for direction in getting this card working - I currently

Pam_SMB allows Linux clients to validate their passwords against an NT PDC, so the only thing you have to do is set up the accounts on the Linux side with an '*' in the /etc/passwd entry. This can be done using a list of users: #!/bin/bash for i in `cat myuserlist`; do /usr/sbin/adduser -p '*' $i with various other command line options, such as "-s

Hi All; How can I test manager.conf? Can I telnet to the asterisk machine at the port 5038 and send and receive commands to test if the manager is working fine? How? Regards Bilal

Hello, I saw the problem quite often in various posts but could not find a real solution . Problem is that I frequently get annoying popups from outlook 2007 about imap idle timeouts which block working with outlook until the popup is acknowledged. The popup says: Your IMAP server closed the connection. This can occur if you leave the connection idle for too long. Protocol: IMAP Server:

Hello asterisk-users, I setup my asterisk to support several features like automon,blindxfer,atxfer,parkcall etc. by using features.conf and the global variable DYNAMIC_FEATURES=automon#blindxfer#atxfer#parkcall#disconnect in extension.conf. Every Dial() command in my diaplan has the appropriate parameters out of {tTkWwW}. For calls from my SIP phones everything works fine. Pressing #1 will

This is my first attempt to write software of any sort. What I am trying to is to use a .php page to query asterisk Manager and get the ExtensionState for each particular extension. Then when it has the answer it outputs an XML file for use as the directory on a Cisco 7960 phone. What I am thinking is that when the user hits the directory button to veiw the directory that is at this URL it will

Please, remove my registration from your mailing-list. For weeks I tried everything I could, but without any response!! I followed all hints found under http://samba.anu.edu.au/listproc Sincerely Bernhard Himmel himmel@warnow.e-technik1.uni-rostock.de himmel@saphir.physik1.uni-rostock.de himmel@physik1.uni-rostock.de > Reply-to: samba@samba.org > From:

I've got plenty of messages about "message command". Please don't talk me about "message command". I have "message command" in my smb.conf. It seems to be another problem: I can browse all groups in local network but anyone can't find me in "Network neighboorhood" in Widows 9x. I can receive popups only from boxes with samba (Linux boxes) and

Hi, I''m using lightbox.js for displaying chromeless popup windows. I have a main page on which I have javascript_include_tag and stylesheet_link_tag to include lightbox. Calls to the lightbox popups from this main page work perfectly... But....calls to the lightbox popups from pages which are called by ajax(using link_to_remote) from the main page do not work... :( They work like

Hi I've a Sangoma A200D with 2FXO and 2FXS. When using it with only the FXO module, it's all good. But when I put in the FXS module and connect the power, logs tells me not enough power. > Mar 31 14:11:54 phone kernel: [ 4761.246931] wanpipe1: Module 1: > Failed to powerup within 600 ms (8V : 72V)! > Mar 31 14:11:54 phone kernel: [ 4761.246937] wanpipe1: Module 1: Did

I'm not sure how much more simple I can make this but I just cannot seem to get my Asterisk 13 to accept a connection on the manager interface: --- manager.conf --- [general] enabled = yes port = 5038 bindaddr = 127.0.0.1 [myasterisk] secret=a permit=0.0.0.0/0.0.0.0 read = all write = all So, couldn't be any more wide open and simpler to connect yet: # echo -e "Action: