similar to: capi installation problem

Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info

Hello, I'm trying to install CAPI Driver for Suse 9.2 and I found the documentation for this pretty old since It refers to Suse 8.2 ( http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install ). This is especially apparent when I look at the section of these instructions for altering "src.drv/makefile" to replace the occurance of "CARD_PATH". I tried to

Hello all, I'm trying to setup a AVM C2 card. I have read the kernel requirements for this card. <M> CAPI2.0 support [*] Verbose reason code reporting (Kernel size +=7K) [*] CAPI2.0 Middleware support (EXPERIMENTAL) <M> CAPI2.0 /dev/capi support [*] CAPI2.0 filesystem support <M> CAPI2.0 capidrv interface support My problem is when I make a "make

I'm using avm fritz card usb with kernel 2.6 patch with mISDN. The module is load correctly when I type lsmod I've got the following output: Module Size Used by zaptel 178308 0 avmfritz 21388 0 mISDN_isac 14336 1 avmfritz mISDN_dsp 191424 0 l3udss1 34184 0 mISDN_l2 39040 0

HI, I tried to install asterisk and mISDN via http://www.asterisk.org/downloads/yum My machine is running with kernel-2.6.18-164.15.1.el5.i686 # grep kernel /var/log/yum.log Mar 21 16:09:28 Installed: kernel-2.6.18-164.15.1.el5.i686 Mar 21 16:09:42 Installed: kernel-devel-2.6.18-164.15.1.el5.i686 I've installed the following packages: # yum install asterisk16-misdn mISDN mISDNuser

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi ! I've fetched a spare AVM B1 card from the cellar, and installed it. After "modprobe b1pci" I did "capiinit" and capiinit moaned about a missing t1.b4. So I search the web and found one at http://www.avm.de/ftp/cardware/b1/x_misc/ddi/. When I now look at the controller, I finally see p2p-mode: # cat /proc/capi/controllers/1 name b1pciv4-a400 io

Hi Jon, perfect instructions, thank you very much. I used them and after some tests they worked. Here is what I did. Maybe someone could use it completely: ------------------------------------------------------------ Install helpers: apt-get install kernel-package ncurses-dev fakeroot wget bzip2 Go to usr directory: cd /usr/src wget

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hello ! I would like to get working a Fritz PCI card using chan_misdn operating in ptp mode. Afer compiling mISDN into the kernel and building chan_misdn Asterisk stops loading with : [chan_misdn.so] => (Channel driver for mISDN Support (Bri/Pri)) == Parsing '/etc/asterisk/misdn.conf': Found UnLocking config_mutex == Registered channel type 'mISDN' (This driver enables

Hi! I am trying to export a PCI device (an AVM Fritzcard PCI ISDN card...) to a domU but when starting my domU I am getting this error: "pciback pci-4-0: 22 Couldn''t locate PCI device (0000:00:06.0)! perhaps already in-use?" My system is running both debian etch in dom0 and domU... Below you can find (hopefully) all important information... Sincerely, Gaubatz Patrick

Hello, list a have a problem i can start asterisk, i get the fowlling error: [chan_capi.so] => (Common ISDN API for Asterisk) == Parsing '/etc/asterisk/capi.conf': Found Feb 11 13:50:36 NOTICE[2535]: chan_capi.c:2636 load_module: CAPI not installed! Feb 11 13:50:36 WARNING[2535]: loader.c:345 ast_load_resource: chan_capi.so: load_module failed, returning -1 Feb 11 13:50:36

Hi list, I installed a fresh Debian/Etch with Asterisk 1.4 and Zaptel 1.4 from SVN for 2 Digium B410P card. I ran configure in Asterisk dir, went in zaptel dir and: make, make install, make b410p. Everything is ok. Now I want to compile Asterisk but can't activate the chan_misdn channel which depends on -from menuselect- isdnnet(E), misdn(E), suppserv(E) When I made the make b410p, all

Hi, I'm trying to get Asterisk working with the AVM B1 card. I've tried every instruction set I can find, but to no avail. I think I'm getting mixed up as to what Zaptel/CAPI configuration to use. If someone is currently using one of these cards, would it be possible to mail me a few bits of the important config files? Sorry if I should have included something else too, but let me

Hallo all, I am trying to get * with chan_capi and a ptp-ISDN with 4 lines on a AVM C4 card to work. But weather inbound nor outbound is working :( My capi.conf: ; ; CAPI config ; ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] mode=immediate isdnmode=ptp msn=8993 incomingmsn=* mode=immediate controller=1,2,3,4 softdtmf=1 ;accountcode= context=demo

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hello I'm newbie in asterisk and i have a "AVM Audiovisuelles MKTG & Computer System GmbH Fritz!PCI v2.0 ISDN (rev 02)" with CAPI Driver. I would like install fax detection, but i don't know if i should use NVBackground detect; or CapiAnswerFAx; or other. I don't understantd operation of fax. Tx ps: sorry for English i'm french

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)