similar to: Problem with TE212P

Hi, I am having problems with an Asterisk with a Digium TE205P card. The issue is that the Ring Back Tone is noisy. I am making modem's calls and this noise influences on the initial negotiation protocol, so modems have to recall. My configuration is: Asterisk version: Asterisk 1.4.21.2 Linux version: CentOS release 5.2 (Final) Card: Digium TE205P

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the

Hi, I'm trying to get a TE212 working on a Dell PowerEdge 1850 running Debian etch using the latest release of libpri (1.4.0), zaptel (1.4.2.1) and asterisk (1.4.4). The initilization of the Octasic echo canceller seems to fail when the wct4xxp module is loaded. [...] VPM450: echo cancellation for 64 channels Failed to open chip, code 00103017! VPM450: Failed to initialize [...] By looking

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Hi all, I've setup a PBX in production environment last week but we have immediatly find out drop conversations and lot of errors (in asterisk logs) like: Apr 10 17:30:48 NOTICE[25154] chan_zap.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 My configuration is: Motherboard: SuperMicro P8SCT (Intel E7221 chipset) Hypertrading and APIC enabled CPU: P4 3GHz Digium TE205P

Hello, I`ve got a problem which I can`t deal with. I own 2 cards - TDM2400P and TE410P. I`ve put them into a HP Proliant DL380 G4 server, compiled the drivers according to the manual. Unfortunetly there are both cards channels are configured in zaptel.conf file the first module (in this file) sends an error. For configuration: span = 1, 1, 0, ccs, hdb3, crc4 fxsks = 21-24 bchan = 25-39,

Hi, On a Asterisk 1.8.12 system working OK for months (>100k calls proceed), users are complaining for bad audio. My setup is: PSTN <--E1/PRI ---> Asterisk <--- E1/PRI---> Siemens HiPath <---E1/PRI ---> PSTN asterisk -rx "dahdi show version" DAHDI Version: SVN-trunk-r10414 Echo Canceller: HWEC asterisk -rx "pri show version" libpri version: 1.4.12 A

I have my peers registered to SER.asterisk seems to be sending mwi for the peers seen in the sip show peers CLI command. i have my ser server registered with asterisk as a type=friend and all clients register to ser.how do i get mwi to work for these clients registered to SER. Thank you, -AA

hello list, i have installed 2 diguim cards in my server using asterisk 1.4 (i use the old version with zapata.conf and zaptel.conf) i want to use the span 1 for group 1 and span 2-span 6 for the group 2 (i want to active the round-robin for span 2 and 6) in order to activate the WIMAX and FH please see the configuration below and tell me if there is anything wrong question 2: what is

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

hi after some testing with A@H, i've decided to install my asterisk server on a slackware (because it's my favourite distro and it is still suggested here http://www.voip-info.org/wiki-Asterisk+Linux+Slackware) , so, i've installed the last 10.2 release, and i've recompiled the 2.6.15.4 kernel. then i've downloaded asterisk1.2.4 and zaptel1.2.4 i load module zaptel and

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Guys, I'm trying to configure a TE406P with MFC/R2. here goes my zaptel.conf: span=1,0,0,ccs,hdb3,crc4 cas=1-15:1101 dchan=16 cas=17-31:1101 span=2,0,0,ccs,hdb3,crc4 cas=32-46:1101 dchan=47 cas=48-62:1101 The first strange behavior is that the: zap show status shows this: Description Alarms IRQ bpviol CRC4 T4XXP (PCI) Card 0 Span 1

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Quoth Jon Morgan <jon.morgan at motors.co.uk> > >We have a 2 port Digium TE220P card, one span is configured to connect to our ISDN30 provider (British Telecom), the other span connects to our internal PBX. Here's the zaptel.conf snip: > >span=1,1,0,ccs,hdb3,crc4 >bchan=1-15 >dchan=16 >bchan=17-31 > >span=2,0,0,ccs,hdb3,crc4 >bchan=32-46 >dchan=47

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31