similar to: SER / IAX solution

I just changed the from DSL to Shaw Cable (static IP) configure the firewall but now asterisk I can not register with FWD nor VoipJet calls going out. I am using IAX with FWD Did I missed to change a setting? I don't think there is any though. I am on shaw extreme connection; I just talked shaw tech. and they are not blocking any port - I was told. So why IAX will not register with FWD and

I'm testing Teliax tall free number line and I'm experiencing long delay about 1sec. during conversation. When I call myself over FWD the response is normal no delay or cut messages. When I call my number over FWD the is a long delay, welcome message usually cuts off few first words and during conversation my voice arrives after about 1sec. delay. Since, the 800-number is only accessible

What are the alternatives to FWD with IAX2 registration capability. FWD is great, but their IAX2 is not the priority and if it goes down it takes days to restore it. I want to use IAX2 protocol but the end point (Sipura unit) need to be able to register over SIP behind firewall. Line1 is registered with FWD PSTN need to be registered with somebody else. What are my alternatives? -- #Joseph

When I try to call out to FWD over IAX2 I get: Call rejected by 65.39.205.121: Unable to negotiate codec I'm using asterisk-1.0.5 (the same settings works fine with *0.9) I've standard settings in iax.conf [general] bindport=4569 register => xxxxx:xxxxxx@iax2.fwdnet.net [iaxfwd] type=user context=fromiaxfwd auth=rsa inkeys=freeworlddialup disallow=all allow=ulaw -- #Joseph

Does anybody have a good link how to connect Sipura with Asteriks, both behind NAT? I'm using FWD but their connection is like a weather (especially IAX), I need something more reliable. I was thinking of using stun and/or proxy but can not find any good link explaining how to setup Linux server -- #Joseph

I've setup my IAX2 over FWD and it is working I can receive a test call and I can call out. Though I cannot figure out how to dial 1-800 numbers over FWD When I dial 1-800 it hangs up on me. Here is a typical session: Called xxxxx:xxxxxxx@iax2.fwdnet.net/18007425877 -- Call accepted by 65.39.205.121 (format ULAW) -- Format for call is ULAW -- Hungup

Has anybody tried NVFaxDetect Fax detection for sip SIP/IAX channel? There is a new application from Newman Telecom for fax detection. http://www.sineapps.com/news.php?rssid=575 Current Asterisk Fax detection doesn't work for me as I don't have Digium cards; I'm using Siupra -- #Joseph

I'm just curious why Sipura isn't using free IAX protocol with their devices instead of SIP? With IAX NAT traversal would have been easier, so why are they using SIP. Is there any politics in it? -- #Joseph

Hi All; Till now I am not able to find a good IAX IP Phone or Gateway that can be used with good quality. Anyone can advise for good one? Regards Bilal ____________________________________________________________________________________ You rock. That's why Blockbuster's offering you one month of Blockbuster Total Access, No Cost.

I have an incoming 800-number over IAX from Teliax and I'm experiencing the large packet loss on connection. When a call comes in there is no ring tone and the first few words of the welcome message are cut off, regardless of the delay I set. Standard call (not 800-number) coming over IAX with the same provider works just fine only the tall free number. So it seems there are some packet loss

I know FWD uses a SER/Asterisk combo, and I keep hearing about the massive benefits, however, my initial playing around in SER's configuration indicates it's NOTHING like Asterisk at all, and almost 5x as difficult to understand and configure. But that's only after a few hours of playing with it. I'm interested in learning SER more, especially the integration with Asterisk. Is

I have seen a lot of references to SER. Currently, I have: 1 PRI to Telco 1 PRI to old PBX Several SIP phones with the intention of having approx. 200. I do have people that travel with softphones (currently X-Lite, but will be testing EyeBeam for better codec and echo cancel capabilities) Currently the traveling users have to VPN in first which I am sure is adding extra overhead to the calls. I

Hi, We are testing a SIP solution * + ser solution for a large implementation. All the clients are nated. When a client is dialing outside the domain (to a FWD sip account for example) all is perfect ! ;-) But ,when a call is done to a sip account, the client is ringing, then the caller can hear the nated client very well, but the nated client does'nt hear anything. RTP issue no ? I've

We are planning to install a voip system based on asterisk for 2000-3000 retail locations and up to 6000-8000 sip accounts/users. Instead of setting up a new, centralized PSTN gateway, we are intend to use a CISCO gateway/router of an existing CISCO voip solution in the headquarter and we must able to call all CISCO based voip phones in the headquarter running together with a CCM. SIP-Phones

Hi, I'm now setting up a VoIP conference room using Asterisk. All the clients are SIP phone (to be exact, Xlite), number of clients that should be registered are around 50 and concurrent users are maybe 15 clients at most. So, basically I think I can handle the situation only with Asterisk. I'm wondering however, most of my clients are behind NAT of home router and using SER together

One for the gurus.. I have seen there has been a lot of discussion about using SER with Asterisk.. This to me seemed like an over kill becasue it would basically be doing most of what Asterisk is doing anyway unless you create some weird and wonderful config in SER.. Anyway, I decided to go and have a quick read through the SER docs and in the section about NAT they say that the best way to

I would like to implement enum lookup in my dial plan but searching for solution / implementation I'm getting confused what is current standard. On some pages I read that the ENUMLOOKUP is not in development anymore and suggesting on using Enumlookup.agi scrip , some are saying that Asterisk 1.2.0 comes with a new powerful ENUMLOOKUP. So there is probably no need to use this script anymore;

I've setup SPA-3000 and when the calls come through my phone is rining almost instantly but the [demo] doesn't answer till after about 13 seconds. So I have about 13 seconds delay and I don't know what setting is causing it; here is a part of my settings from extension.conf. [from_pstn] exten => 1000,1,Goto(demo,s,1) [demo] exten => s,1,Answer ; Answer the

Is anybody familiar with these IP phones AT-723 or AT-323 I think it is made by this company: http://www.atcom.com.cn/at723E.html -- #Joseph

After somebody records a message asterisk notifies me and encloses the WAV file. Though I'm not sure if this is a WAV format. I can not play it. According to the file specification it is: msg0000.WAV: RIFF (little-endian) data, WAVE audio, GSM 6.10, mono 8000 Hz How to play received message? -- #Joseph