similar to: Trixbox ;TE110P ;DELL OPTIPLEX GX240

hi eveybody, after many test with your help and the irc channels help, i get the led on TE110P green with this config: span=1,1,0,ccs,ami =====> alarms OK Green Led but the provider say that i have to set my span to this span=1,1,0,ccs,hdb3,crc4 =====> alarms: YEL/RED i can't make call's yet to test because they have to sync the Modulator in the other side so any remark? is my

re Hi, I m looking for a good document that allow me to install zaptel libpri & asterisk without errors, i ve a TDM400 & TE110P, so please can you help me Kind Regards Younss AZZAYANI KASTERISK.COM

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

Hi everybody, i need someone to tell me the spins numbers of Rx+,Rx-,Tx+ and Tx- of TE110P and also if you can tell me have to made a cable like that?? Modem Teleco <-----------Self Crosscable------------>Asterisk Rx+ <--------------------------------------------------------------> Tx+ Rx- <--------------------------------------------------------------> Tx- Tx+

i get this message with a red signal on TE110P card: ***************** TE110P: span configured for... Calling startuo (flug is 4099) wcte1xxp: Setting yellow alarm ***************** what does mean ? thank you :)

Hi every body, I've set up a Trixbox Server with TE110P,all things seem to work fine(Thank You Malling lists & irc & Forums), but i need your help, i ve 30 numbre from 60 to 89, i need to specify for each sip extension a Zap number for example to call the sales service the caller must call 555-4570 and automaticly the caller will be redirected to the 202 ( sales service ) so nobody

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi all, I'm sure something similar has been discussed, but one can only wade through the archives for so long. I'm setting up a T1 and my telco has a bunch of questions it wants me to answer. I know much of the TE110p is configurable to do any of this, but I wanted to know if there is an optimal or preferred setup. Any help would be appreciated. Here is the quiz my telco is giving me:

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

hello, i ve a lot of probl?me with zaptel 1.4 when i tried to complile it under debian kernel 2.4; so i need to compile a new kernel version 2.6.x but id don't witch kernel version is stable van you help me please? :) Younss AZ KASTERISK.COM skype: younssiga

when i compile zaptel make linux26 make install i got these errors: make[1]: Leaving directory `/usr/src/zaptel-1.4/wct4xxp' make -C datamods clean make[1]: Entering directory `/usr/src/zaptel-1.4/datamods' make -C /lib/modules/2.4.27-3-386/build SUBDIRS=/usr/src/zaptel-1.4/datamods clean make[2]: Entering directory `/usr/src/kernel-headers-2.4.27-3-386' make: *** arch/i386/boot: No

Hi List, I'm trying to install X-Lite in Dell Optiplex GX-280 but I'm experiencing sound problems. When I configure the Audio Tunning Wizard all seems fine, but whe I make a call the sound quality is the worst. The sound is very noisy, with very low volume and gaps without sounds. I've tried with 3 desktops CPU with the same result. The onboard sound device is a SoundMax Integrated

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????

Hello, Digium support kindly proposed to ship a TE120P card to help resolve the issue. I plugged in the card, and introduced the loopback plug. I cleared the red alarm for a while and then i started seeing alarm switching from Yel/Recovering to Blue/Rec with a lot of IRQ Misses. I call Digium that assisted us, and we noticed IRQ sharing with the VGA adapter and the Ethernet port. I changed

Fedora Core 6 regards, Pablo. On Thu, Mar 08, 2007 at 05:01:15PM -0800, Jose Bertuzzi wrote: > Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: > ??? Alarms Span ??? OK Digium

Hi everyone I have a Digium card TE110P and after plug it, turn on the computer and configure, the LEDs don't light up in spite of what Digium FAQ says about the LEDs: When will the LED's light up on my TDM400P/TE110P/TE2XXP/TE4XXP? ... The TE110P LED's will light up RED when the span is configured and kernel module is loaded. If configured correctly and a circuit or channel bank is

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

Hi folks, I've already searched the mailing list but no one else seems to have my same problem. I'm using Asterisk with the following configuration: Fedora Core 4 (but I also tried Fedora 3) 1 Digium TE110P 1 TDM40B 1 HFC-S 'Cologne' bristuff 0.2.0-RC8o (zaptel 1.0.9.2) I compiled right, I can load kernel modules but when I try to unload wcte11xp module (the one

Hey there, What recommendations does anybody have as to motherboards known to work well with the Digium TE110P T1 interface cards and the TDM400P analog POTS interface cards? We currently make use of the TE110P for our T1 (esf w/ b8zs - not a PRI) and have experienced many issues caused by our PBX's motherboard. Additionally, we built a server to become our new PBX, but that machine runs