similar to: Asterisk Inbound Problem

I was doing a daily make update for asterisk. On the 19th the new version compiled fine. I installed it. All of my ata 186's can call out to pstn etc. All inbound calls, the phones ring but when you pickup, just silence both local and remote with no complaints in the cli. I backed down to the r 1.0 1.0.3 on the 20th CVS-v1-0-12/20/04-18:24:52 it worked ok. Yesterday I did a cvs update on the

I've got a small office setup with a TDM400 and 3 FXO cards. I'd like to take away the ability of the 3rd FXO to receive calls (as this line runs through our old-fashioned fax machine) BUT still be able to use it for outbound calls. With our original, and very basic PBX we could modify the auto attendant on a particular PSTN line to pick up after 4 rings (which would allow the fax to

Hello, After much searching of voip-info.org and google, I'm finally giving in and asking the list. The setup I have is this:- Single X100P card in a Debian system Inbound/Outbound POTS line connects to the X100P Sipura 2000 and Budgetone 100 on the LAN 1 Cordless and one conventional phone connected to the sipura Account on Stanaphone.com for eitherbound SIP calls. (I have other SIP

Hi, i have 2 dovecot imap server running on solaris 10 The primary server with dovecot 1.0.alpha4 is running with best performance on Sun Sparc E4k5 with 8x 450MHz The secondary with rc10 has ugly performanceproblems on Sun E450 wth 4x 450MHz. Every new imap process takes permanent 25% cpu usage List the folder and fetch message are both slowy! Both servers are configred with ldap backend

Howdy, 1 x TDM400P card with 1 x fxo module. 1 x BT Pots line. Location - UK Calls work fine outbound but i'm unable to pickup the inbound calls. Asterisk debug: Asterisk -vvvvvvvvvvcg *CLI> -- Starting simple switch on 'Zap/1-1' -- Executing Wait("Zap/1-1", "1") in new stack -- Executing Answer("Zap/1-1", "") in new stack

Hi All; Is there a softphone that can be installed on a mobile (new mobile models), so it can work with Asterisk as following: 1) As SIP or H323 client, with the ability to add button functionalities (call pickup, call transfer, ...) so if there is a wireless network, then it can use it to connect to Asterisk and work as client, but from the Mobile. 2) If there is no wireless network, then it

Hi! > How to do this ?? > To proceed with your answer on PICKUPMARK, where do I put this ??? Look at the example for Asterisk 1.4 on this page: http://www.voip-info.org/wiki/view/Asterisk+cmd+Pickup Philipp

Hello All, I have a issue with park and pickup feature. I have asterisk 1.4.35 branch, Here is the scenario for the park and pickup. I have changed parking feature with *72 for my asterisk in features.conf. When i have inbound call it comes to one extension or ring group and then I put that inbound call in parking. After that I will dial some extension to get that call back, I am using

I'm having trouble with call pickups. Suppose ring group is 100 and has extensions 101 and 102. Someone calls 100, 101 rings and 102 wants to pick the call up. If 102 dials **100, call pickup works. If 102 dials **101, call pickup fails. In my dialplan I have: exten => **101,1,NoOp(pickup extension) exten => **101,n,Pickup(101) exten => **101,n,NoOp(pickup group) exten =>

Hi, I have an asterisk 1.2.1 on a Debian Sarge distro with *three* TDM400P (12 fxo ports). I noticed Asterisk is slow to answer inbound calls so I connected an analog phone in parallel to make a test: __________Asterisk fxo ---- line -----| -----------------Analog phone The analog phone rings immediately when calling, while asterisk shows the message

Hey there list ! I'm receiving negative feedback when people try to pickup another ringing phone by pressing *8 on there own Grandstream device. These are my setting that should make pickup possible : all my sip-clients (Grandstream) have this in their config (sip.conf) : callgroup=1 pickupgroup=1 canreinvite=no qualify=yes So they are all in the same pickupgroup... This the

Hi All, I'm using Asterisk 1.2.14 under openSuSE 10.2 with kernel 2.6.18. I have Wildcard TDM400P card and D-Link DPH-120S and DPH-140S SIP phones. I would like to be able to pickup ringing extention from any SIP phone using Pickup() application. from my dial plan: [incoming] exten => s,1,Dial(SIP/somebody1|60|tTrR) [internal] include => outbound-local include => parkedcalls

Hi all, I have a GXP2000 with BLF configured. I follow the configuration guide to enable the pickup cmd as follow and include it under corresponding content. [BLF_group_pickup] exten => _**1XX,1,Pickup(${EXTEN:2}) exten => _**1XX,n,Hangup The I press the single key to pickup the call to extension 100 when there is a call to it. From CLI, I can see it issue **100 to asterisk but failed

I'm using the Debian Sarge package of Asterisk - 1.0.7 + bristuff. When I call from a zap channel or a SIP phone to another SIP phone, then dial *8 from a third SIP phone, I get 503 Service Unavailable on the third phone and I get this at the Asterisk console: Jun 28 09:01:24 DEBUG[16774]: res_features.c:1709 ast_pickup_call: No call pickup possible... Jun 28 09:01:24 NOTICE[16774]:

Hi, What do I need to do to get asterisk to NOT pickup a Zap channel when it rings? The channel in question is used for outbound calls only, and all incoming calls are answered by an analog phone elsewhere in the building that does not run through asterisk... so.. either make it not answer.. or make it delay for like 90 seconds.. I've tried wait's.. but it still seems to pickup the

I cannot use CVS, is there anoyher way to use direct pickup ? Thanks again Giordano ________________________________ Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Alexander Lopez Inviato: venerd? 16 settembre 2005 17.53 A: Asterisk Users Mailing List - Non-Commercial Discussion Oggetto: RE: [Asterisk-Users] direct sip call

We are installing Aastra phones (480's and 57i's) into a fairly simple asterisk setup. Although call park & pickup work fine using xfer to 700 (to park), dial 701 (to pickup), we are unable to make the park/pickup softkey feature work on the aastra's. Although we've programmed the softkeys per the manuals, they seem to have no effect (just dead). For example, our 57i is

Getting module_request errors from SELinux. Errors being thrown by metacity sendmail.postfix cleanup trivial-rewarite local postdrop pickup All errors are essentially the same System was working well until I began to apply some basic security hardening configuration. Postfix started complaining when I made /tmp noexec, nodev, nosuid, and then did a mount --bind of /var/tmp under

Hey guys, I'm in kind of a crunch right now. Due to a poorly written script that I don't have control over, I need to be able to map a drive letter to a Samba share so that it works seamlessly with UNC (i.e \\server\Share <file:///\\server\Share> ). Basically, I need a way for a share name with a $ in it to be recognized as a valid network name. My current setup is like so:

Hello list, I try to pick up a ringing extension but nothing works. To be clear, I'm trying to pick up extension 10. [Jun 14 17:37:34] -- Executing [**10 at from-TESTCORP:4] Pickup("SIP/testcorp3-00000041", "10 at 123456") in new stack [Jun 14 17:37:34] NOTICE[16555]: app_directed_pickup.c:159 pickup_exec: No target channel found for 10. [Jun 14 17:37:34] --