similar to: CPU & motherboard for 100+ simultaneouse calls on Digium Quad E1 TE411p

Hi, I have a function that I'm writing. The arguments in the function are as follows RFF<-function(qtype, qOpt,...){} i.e., I have two args that are compulsary and the rest are optional. Now when my user passes the function call, I need to see what optional args are defined and process accordingly...what I have so far is.. RFF<-function(qtype, qOpt,...){ mc <-

I was reading the posts and someone said about the default 1000 to 2000 I see in the .conf the default is 10000 to 20000 I found a service that gives inbound DID's in the firewall 5060 and 10000 - 20000 is setup no workie on the DID But when I set 5060 , 10000 - 20000 and (Unblocked) 1000 - 2000 Now the DID works fine. So you me what the standard is -- Best regards, Al Bochter Bochter

Hi Guys, I need your recommendation which card to buy?The TE411P or TE406P do they have any difference?I check their brochures they are differ only when it comes to PCI slot voltages.Which card best to use?Btw,Il be using supermicro board with 3.3V and 5.5V?Will il be experiencing problem during the implementation later on if i choose the wrong PCI voltage options?Will it depends on

I checked the list of what not to use, but am still having no fun trying to find a working box. Can someone suggest a Compaq or Dell or MPC or . any other brand and model that is known to work well with the TE411P ? Will an old Proliant do? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi All This mail is from a new comer to asterisk , just exploring I was going through the digium web site , In need some advice and suggestions , which card I should chose , should I choose TE411P (with on board echo cancellation ) or TE410P If I go for TE411P , I will be spending 1,000 $ more and for me finance part is critical , will I face

I changed from a TE410P to a TE411P and fax carriers weren't detected anymore ! I have tried everything (recompile zaptel+asterisk+spandsp ; echocancel=yes/no ; rxgain=0/txgain=0 ; increase Wait() ; ...), nothing worked. The only solution that worked for me was to install and use NVFaxDetect. HTH.

I have seen conflicting references in regards to the Digium Wildcard TE411P echo settings in zapata.conf. Does anyone have the official word on this? Should echo cancel be enabled in zapata.conf if the card has built in EC? If so, should a particular EC method be compiled into the zaptel build? My reference, which has echo: My zaptel is 1.2.5 context=from-pstn switchtype=national

Hi, I found E400P quad PRI card quite cheap (749USD): http://www.govarion.com/product_info.php?cPath=1&products_id=2&osCsid=68cdd6e3d08754 in comparison to te410p (approx 1500 USD ) http://www.digium.com/index.php?menu=product_detail&category=hardware&product=TE410P Now newer generation with HW echo canceling emerged (te411p). I'm not sure in what things those two cards

Hi all, I replaced a TE410P Rev C 1st Generation Firmware with a TE411P without any cfg changes (zaptel/zapata). As a result Asterisk crashes on outbound from PRI4 going to PRI1 calls: Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 Aug 23 18:22:00 WARNING[4693]: chan_zap.c:7545 zt_pri_error: PRI: !! Got a UA, but i'm in state 1

Dear all, Does anyone try to install 2 or multiple TE411 card into one server? Can it be done? What about stability? Thanks Ray -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060209/b65a1d46/attachment.htm

The Orion echo canceller is just ok. The Tellabs units work just as well if you don't mind 10 mins of soldering. I have the orion running with an adit 600 and a TE110P. Echo cancel is fairly good, but I have loads of problems with DTMF digits. -Darren ________________________________ From: asterisk-users-bounces@lists.digium.com

Hi all, 1. Just bought a new TE411P and about to install it replacing the existing TE410P. I am assuming I need to set echocancel=no and echocancelwhenbridged=no now that it will be done in hardware, correct? 2. Is there any way to monitor hardware echo cancellation to ensure it is working (apart from being on a call)? 3. The Digium webite says "By supporting 16ms with 128 channels or

Hi, Probably a stupid syntax problem.. but can't seem to make these files work for more than the first T1 (ok, if I comment out the 2nd, 3rd, and 4th span). Can someone proofread this for me? Thanks! ====================== zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48 span=3,0,0,esf,b8zs bchan=49-71 dchan=72 span=4,0,0,esf,b8zs bchan=73-95

Does anyone know how to disable the VPM in software rather than removing the card altogether? The canceler isn't working as well as the software cancelers were. Aaron

I am looking at the two Digium cards mentioned and am not sure if the echo cancelation is a must. The sever is a 2.8Ghz P4 with 2 GB of ram, and is only for routing PSTN connections to another * server. I would like the advice of the list before making my final decision. -- Bruce Nortex Networks -------------- next part -------------- An HTML attachment was scrubbed... URL:

List, I just tried to swap out our 410 for a 411 and we started have problems with on of our T1's. Setup: Span 1 - Dedicated PRI for long distance. Span 2 - 12 channels fxs_gs outgoing local. 12 Channels em_w incoming DID's. I didn't have any problems with the PRI. The trouble was with the T1. We were unable to place any local calls, and all incoming DID's where garbled.

I am getting ready to purchase my first Digium card to start experimenting with Asterisk. Before I make my purchase, I wanted to make sure I'm not going to have issues with these cards (need to see what the specs are on my box, 5V or 3.3V PCI ). I will be using Asterisk @ Home, so will be Asterisk v1.0.9. I took a quick poke at the lists, and it appears several people have been having

Hi every one, I am using asterisk version 1.6.2...... i did not install mysql data base and when i tried to register a client from SIPp xml file..... it is registered.... My questions are 1. where can i find that registered client? 2. when i type the command "core stop now" it exists and the registered users are not shown why this is happening? 3. Is it compulsary

I just implemented a system using a TE411P hardware echo cancellation card. Per Digium, I setup zaptel.conf, and zapata.conf the same way as I always have. To my surprise calls out to the PSTN had a terrible echo. 1 - 2 second delay, and quite clear. The echo was so bad that I had to remove the hardware echo cancellation module from the card. We are only using the 1st span of this card right

North by Northwest Music Conferences and Festivals has published over 100 Vorbis files of artists who will be playing the fest in Portland, Oregon this September. Available at: http://bands.nxnw.com Vorbis Rules! Thanks, all! David Rose - NXNW Web Team david@sxsw.com --- >8 ---- List archives: http://www.xiph.org/archives/ Ogg project homepage: http://www.xiph.org/ogg/ To unsubscribe from