similar to: Pickup() ringing extension and call waiting

Dear All, I can not transfer call in progress. What's wrong with my macro? I think tT flags is enough right? [macro-stdexten] exten => s,1,Set(temp=${DB(CFU/${ARG1})}) ; Get CFU key exten => s,2,Set(DNDStatus=${DB(DND/${ARG1})}) ; Get DND key exten => s,3,GotoIf($["${temp}" = ""]?5) ; If not existing, goto priority 5 exten =>

Hi All, I've installed Enhanced PickupChan on asterisk 1.2.14 using howto from http://www.thorsten-knabe.de/linux/asterisk/pickup.jsp . from extensions.conf: exten => 0,1,Dial(SIP/eosoiris|20|tTrR) exten => 200,1,Dial(SIP/dzalewski|20|tTrR) exten => _7.,1,Pickup2(${EXTEN:1}) When I try to pickup ringing SIP channel from other IP headset I go disconnected. here is debug from

Hi, list! I'm playing on an Asterisk@home installation, since a month or two. I've had no trouble setting it up 'n running. I've bought a couple of DLINK's DPH-140S SIP Phones, to use with Asterisk. >From this phones, I can make & receive calls with no trouble, but, when I try to use some "interactive" function (eg Directory or Voicemail), the phone seems

Dear All, I'm using Asterisk 1.4.16.2 with Zaptel 1.4.7 on Debian with kernel 2.6.18. I have two analog lines Zap/1 and Zap/2 as group 1 in zapata.conf. I'm using below context for dialing out. [outbound-local] exten => _9XXX,1,Dial(Zap/g1/${EXTEN:1},30,tTr) exten => _9XXXXX,1,Dial(Zap/g1/${EXTEN:1},30,tTr) exten => _9ZXXXXXX,1,Dial(Zap/g1/${EXTEN:1},30,tTr) exten =>

I'm still a learning but I purchased a dph-140s to test with AAH 1.5. I think this is a rebadged ACT P104SLD which others seem to have working with *. It seems to be configured and registered similarly to the softphones I've been using just fine, but it does not receive or send audio (it will send audio to vm), or perform the loopback test. It seems to signal and receive calls fine. The

Hi All, I'm using asterisk 1.2.15 and call forwarding doesnt work for me. from my extensions.conf: ; Unconditional Call Forward exten => _*21*X.,1,NoCDR exten => _*21*X.,2,Set(DB(CFIM/${CALLERID(NUM)})=${EXTEN:4}) exten => _*21*X.,3,Playback(vm-saved) exten => _*21*X.,4,Hangup exten => #21#,1,NoCDR exten => #21#,2,DBdel(CFIM/${CALLERID(NUM)}) exten =>

Dear All, I have a problem with call transfer. When I dial a number and then I want to transfer current call to an extension, I'm getting disconnected. Transfering incoming call works fine. I'm using macro for dialing. extensions.conf: [from-internal] ignorepat => 9 exten => 200,1,Macro(stdexten,200,SIP/dzalewski) [macro-stdexten] exten => s,1,Set(temp=${DB(CFU/${ARG1})})

List, The D'Link phones are not reliable at this time. I am trying to get them fix their Firmware to my specifications. It is half done so far. However there are still hurdles. below email is self explanatory. At present if you want to use these phones, you need to buy D'Link's SIP Server and run this as one of your SIP servers in the blend to call to Asterisk. Seshu Kanuri "G

Hello Situation: I'm moving from a windows XP box to fedora 11. I used winXP to run skype with a dlink dph-50u USB adaptor so that I could talk on skype with my regular phone. Been working fine for months I'm now on fedora 11, able to run skype linux without problem, even the webcam work! Problem, cannot make the dlink dph-50u to work. After a lot of googling, cannot find anything. I

Hi All, I'm having problem with MP3Player app. I want the caller to hear mp3 when he is waiting until I answer my phone. -- from extentions.conf -- exten => 200,1,Answer() exten => 200,2,MP3Player(/home/user200/mp3/hanna-hais.mp3) exten => 200,3,Dial(SIP/200|20|tTrR) exten => 200,4,Hangup() -- end -- here is debug from CLI: -- Executing

hi all I'm trying to setup a dlink dph-100h phone (actually a dph-100m but with the h.323 software) with asterisk and chan_h323. AFACS, the dph-100h software can only be configured to point to a gatekeeper. I know I don't need to do this, but it's a test before I setup my Symbol Netvision phones (I don't have an access point for them now). First, this is what I have, and what

Hello gentlemen, I am new here. I have a D-Link DPH-80S SIP phone (it's a non-US model), and I am trying to make it work with Asterisk. I tried versions 1.0.7 and yesterday's CVS and the behavior is the same. The phone registers with no problem, and can accept calls. But when I try to make outgoing call, there is a series of invite requests from the phone, to which asterisk responds

I have been using the D-Link DPH-540 wireless VOIP handset, and I really like this phone. We had tried the UStarcomm phone, but the phone is used in a noisy environment and the volume wasn't loud enough. The "problem" with the D-Link phone is the Li-ion battery needs to be replaced and D-Link doesn't sell a replacement battery and I haven't found any after-market batteries.

Greetings, I''ve been using ferret with great results now for a while, but in the last week, I''ve been running into some issues. I will occasionally see this message: Exception Message: Lock Error occured at <except.c>:103 in xpop_context Error occured in index.c:5368 - iw_open Couldn''t obtain write lock when opening IndexWriter Which is accompanied by

After 20 cups of strong coffee and wasteing most of tonight and obviously doing lots of googling and emailing many people, i've concluded that dlink voip phones specifically DPH-80 dosent work with asterisk. If anyone has had anymore luck with these phones then me please let me know -- regards Vikram

hi all when I (using my D-Link DPH-100M MGCP phone) press #, I get told 'transfer'. I dial the new number and after that, * just tells me 'meep meep meep' [hangup] any ideas why? -- Roy Sigurd Karlsbakk, Datavaktmester ProntoTV AS - http://www.pronto.tv/ Tel: +47 9801 3356 Computers are like air conditioners. They stop working when you open Windows.

hi seems like things are closing in to something that might look like success. I have one problem left: I don't get ring indicator when I dial out from the h.323 phone... Sound is good, so it doesn't look like a codec problem. I'm using chan_capi with early B3. I also use gnugp to route the calls from the phones to asterisk, as the dlink dph-100h requires this. Debug output follows:

Hi everyone, I am thinking of working on the following ideas for my GSOC proposal based on my discussions with Olly and my own understanding. Rather than focusing on an entire perftest module, I have decided to focus on implementing performance tests for weighting schemes based on a wikipedia dump and in addition to that, build a framework to measure the

Hi I have used fa() to perform a factor analysis of a psychological battery which is thought to have 11 factors. I can identify which factors the loadings relate to easily enough because I can see which items are loading onto each of the columns in the $loading output. However, how can I identify which items or loadings are being used to create each of the columns in the $scores output? I have

Hi All, I am working on creating storage driver domain with xen-4.3.0 . I am referring this - http://wiki.xen.org/wiki?title=Storage_driver_domains&oldid=9371 I have created Storage domain with xl utility of xen, then followed above wiki for rest of the steps, additionally I did install blktap-dkms package also- Following xen processes are running on Domain 0: